Husqvarna 966976701 Two-piece shaft, Air filter, Cleaning the air filter, Oiling the air filter

Page 28

MAINTENANCE

Incorrect carburettor adjustment.

An incorrect fuel mixture (too much or incorrect type of oil).

A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

CAUTION! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/ cylinder. Check that the spark plug is fitted with a suppressor.

Two-piece shaft

The drive shaft end in the lower shaft should be lubricated with grease every 30 hours. There is a risk that the drive shaft ends (splined coupling) on models with two-piece shafts will seize if they are not lubricated regularly.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

Carburettor malfunctions

Starting problems

Loss of engine power

Unnecessary wear to engine parts.

Excessive fuel consumption.

Clean the filter every 25 hours, or more regularly if conditions are exceptionally dusty.

Cleaning the air filter

Remove the air filter cover and take out the filter. Wash it clean in warm, soapy water. Ensure that the filter is dry before refitting it.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

If the machine is used in dusty conditions the air filter should be soaked in oil. See instructions under the heading Oiling the air filter.

Oiling the air filter

Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

Put the filter in a plastic bag and pour the filter oil over it. Knead the plastic bag to distribute the oil. Squeeze the excess oil out of the filter inside the plastic bag and pour off the excess before fitting the filter to the machine. Never use common engine oil. This would drain through the filter quite quickly and collect in the bottom.

28 – English

Image 28
Contents 327P4 327P5X-series KEY to Symbols SymbolsContents Introduction Dear CustomerWhat is WHAT? What is what?General Safety Precautions Personal protective equipmentMachine′s safety equipment Throttle lockoutVibration damping system Stop switchMuffler Cutting equipment Quick release Balance Flex harnessOnly use cutting equipment recommended by us Specification of bar and saw chain Sharpening your chain and adjusting raker clearanceChain General Safety Precautions Tensioning the chain Adjusting chain lubrication Lubricating cutting equipmentFilling with chain oil Checking chain lubricationChecking wear on cutting equipment Chain What to do if lubrication does not workChain drive sprocket May increase the risk of accidentsAssembly Adjusting the harnessFitting the cutting head Fitting the bar and chainAssembly Filling with oilAssembling and dismantling the two-piece shaft Fitting the impact guardAssembly of the saw attachment Fuel Handling Fuel safetyFuel Fuelling MixingStarting and Stopping Check before startingStarting and stopping StartingStopping Safety instructions regarding the surroundings Safety instructions while workingWorking Techniques General working instructionsSafety instructions after completing work Basic working techniquesWithout having the cutting attachment in full view Maintenance CarburettorFine adjustment of the idle speed T Correctly adjusted carburettorLow speed jet L High speed jet HMuffler Cooling systemSpark plug Is damaged it should be replacedCleaning the air filter Two-piece shaftAir filter Oiling the air filterMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataEC-declaration of conformity Applies to Europe only Approved accessories Art No Use withBar and chain combinations Page Page Page Page 1150991-26