Husqvarna 555, 562XPG, 556, 560XPG manual Air filter, Spark plug, Fitting the starter

Page 34

MAINTENANCE

•Lubricate the recoil spring with light oil. Fit the cassette with recoil spring in the starter. Fit the starter pulley and tension the recoil spring.

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions.

•Starting problems.

•Loss of engine power.

•Unnecessary wear to engine parts.

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly

34 – English

against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.

A HUSQVARNA chain saw can be equipped with different types of air filter according to working conditions, weather, season, etc. Contact your dealer for advice.

Spark plug

The spark plug condition is influenced by:

•Incorrect carburettor adjustment.

•An incorrect fuel mixture (too much or incorrect type of oil).

•A dirty air filter.

These factors cause deposits on the spark plug electrodes, which may result in operating problems and starting difficulties.

If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0,5 mm. The spark plug should be replaced after about a month in operation or earlier if necessary.

Note! Always use the recommended spark plug type! Use of the wrong spark plug can damage the piston/cylinder. Check that the spark plug is fitted with a suppressor.

For recommended spark plug, see Technical data.

Page 33 Page 35
Image 34
Page 33 Page 35
Contents 555 556 560XP 560XPG 562XP 562XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle trigger lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesGuide bar Cutting equipment designed to reduce kickbackSaw chain General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral advice on adjusting depth gauge setting Increases the risk of kickbackTensioning the chain Increased if the depth gauge setting isAdjustment of depth gauge setting Too largeLubricating cutting equipment Needle bearing lubrication Checking wear on cutting equipmentFitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting and stopping Starting and StoppingStarting Stopping Before use Basic safety rulesWorking Techniques General working instructionsCleaning Clutch cover causing the chain toJam. Always stop the engine before Basic cutting technique TermsLogs are lying together. Such Tree felling techniqueLimbing Or fatal injuryClearing the trunk and preparing your retreat Felling directionDirectional cuts Felling cut What is kickback? How to avoid kickbackFreeing a tree that has fallen badly Cutting the trunk into logs Carburettor adjustment MaintenanceGeneral Checking the inertia brake release Muffler Tensioning the recoil spring Starter housingChanging a broken or worn starter cord Changing a broken recoil springSpark plug Air filterFitting the starter Needle bearing lubrication Adjustment of the oil pumpLubricating the bar tip sprocket Cooling systemWinter use Air Injection centrifugal cleaningTemperature 0C or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data560XPG 562XP 562XPG Engine Guide bar and saw chain combinations Saw chain filing and file gaugesApplies to Europe only EC Declaration of ConformityEN ISO 121002010, ISO 149822009, EN ISO Page Page Original instructions 1156729-26

560XPG, 560XP, 556, 562XPG, 562XP specifications

The Husqvarna 562XPG, 555, 560XP, 562XP, and 560XPG are part of Husqvarna’s acclaimed line of professional chainsaws known for their power, efficiency, and ergonomic design. Each model caters to the specific needs of forestry professionals, loggers, and serious outdoor enthusiasts.

Starting with the Husqvarna 562XPG, this chainsaw is designed for high-performance cutting in demanding conditions. It features a powerful and efficient X-Torq engine that delivers high torque over a wide RPM range, reducing fuel consumption and emissions. The 562XPG also includes heated handles, which provide additional comfort during cold weather operations. This model is equipped with the AutoTune technology that automatically adjusts the engine settings to varying conditions, ensuring optimal performance without the need for manual tuning.

Next in line is the Husqvarna 555, a robust chainsaw that strikes a balance between power and weight. It is also equipped with the X-Torq engine, making it both fuel-efficient and environmentally friendly. The 555 features an innovative air injection system that removes large debris particles before they enter the air filter, ensuring a longer air filter life and reliable performance. Its lightweight design and excellent balance make it easy to control, even during extended use.

The Husqvarna 560XP is another powerful option, particularly favorable for tree cutting and harvesting. It boasts a professional-grade engine with a higher RPM capacity and advanced air management, maximizing efficiency and cutting speed. Its ergonomic design incorporates features like a low-vibration system and an adjustable oil pump, which improves user comfort and allows for optimal chain lubrication.

The 562XP is similar to the 562XPG but without the heated handles, providing an excellent choice for users who prioritize performance in milder climates. Its lightweight construction coupled with a slim design enhances maneuverability, making it ideal for both professional use and meticulous backyard projects.

Lastly, the Husqvarna 560XPG combines the features of the XP models with the added benefit of heated handles. This saw is engineered for rigorous tasks, featuring robust construction and advanced features like the LowVib system that effectively reduces vibrations. This model is well-suited for those who face harsh weather conditions, ensuring maximum comfort and efficiency in the field.

Collectively, these Husqvarna models represent the pinnacle of modern chainsaw technology, showcasing features that emphasize performance, user comfort, and reliability for all kinds of challenging cutting tasks. Whether you are a professional logger or a passionate homeowner, there is a Husqvarna model to meet your needs.
Top Page Image Contents