Husqvarna 562XPG, 555 Tensioning the chain, Increased if the depth gauge setting is, Too large

Page 14

GENERAL SAFETY PRECAUTIONS

data to find the correct depth gauge setting for your particular chain.

A

C

B

 

!

WARNING! The risk of kickback is

 

increased if the depth gauge setting is

 

 

too large!

 

 

 

Adjustment of depth gauge setting

•The cutting teeth should be newly sharpened before adjusting the depth gauge setting. We recommend that you adjust the depth gauge setting every third time you sharpen the cutting teeth. NOTE! This recommendation assumes that the length of the cutting teeth is not reduced excessively.

•You will need a flat file and a depth gauge tool. We recommend that you use our depth gauge tool to acheive the correct depth gauge setting and bevel for the depth gauge.

•Place the depth gauge tool over the chain. Detailed information regarding the use of the depth gauge tool, will be found on the package for the depth gauge tool. Use the flat file to file off the tip of the depth gauge that protrudes through the depth gauge tool. The depth gauge setting is correct when you no longer feel resistance as you draw the file along the depth gauge tool.

14 – English

Tensioning the chain

 

!

WARNING! A slack chain may jump off

 

and cause serious or even fatal injury.

 

 

 

 

 

The more you use a chain the longer it becomes. It is therefore important to adjust the chain regularly to take up the slack.

Check the chain tension every time you refuel. NOTE! A new chain has a running-in period during which you should check the tension more frequently.

Tension the chain as tightly as possible, but not so tight that you cannot pull it round freely by hand.

•Undo the bar nuts that hold the clutch cover/chain brake. Use the combination spanner. Then tighten the bar nuts by hand as tight as you can.

•Raise the tip of the bar and stretch the chain by tightening the chain tensioning screw using the combination spanner. Tighten the chain until it does not sag from the underside of the bar.

•Use the combination spanner to tighten the bar nuts while lifting the tip of the bar at the same time. Check that you can pull the chain round freely by hand and that it does not sag from the underside of the bar.

The position of the chain tensioning screw on our chain saws varies from model to model. See instructions under the heading What is what? to find out where it is on your model.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents 555 556 560XP 560XPG 562XP 562XPG KEY to Symbols Symbols on the machineSymbols in the operator’s manual Contents Introduction Dear CustomerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawPersonal protective equipment Machine′s safety equipmentAlways use common sense Chain brake and front hand guardGeneral Safety Precautions Right hand guard Throttle trigger lockoutChain catcher Vibration damping systemMuffler Stop switchCutting equipment General rulesSaw chain Cutting equipment designed to reduce kickbackGuide bar General information on sharpening cutting teeth Sharpening your chain and adjusting depth gauge settingGeneral advice on adjusting depth gauge setting Increases the risk of kickbackTensioning the chain Increased if the depth gauge setting isAdjustment of depth gauge setting Too largeLubricating cutting equipment Needle bearing lubrication Checking wear on cutting equipmentFitting a spike bumper AssemblyFitting the bar and chain Working with the chainFuel Handling FuelTransport and storage Fuel safetyFueling Long-term storageStarting Starting and StoppingStarting and stopping Stopping Before use Basic safety rulesWorking Techniques General working instructionsJam. Always stop the engine before Clutch cover causing the chain toCleaning Basic cutting technique TermsLogs are lying together. Such Tree felling techniqueLimbing Or fatal injuryDirectional cuts Felling directionClearing the trunk and preparing your retreat Felling cut Freeing a tree that has fallen badly How to avoid kickbackWhat is kickback? Cutting the trunk into logs General MaintenanceCarburettor adjustment Checking the inertia brake release Muffler Tensioning the recoil spring Starter housingChanging a broken or worn starter cord Changing a broken recoil springFitting the starter Air filterSpark plug Needle bearing lubrication Adjustment of the oil pumpLubricating the bar tip sprocket Cooling systemWinter use Air Injection centrifugal cleaningTemperature 0C or colder Heated handlesMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical data560XPG 562XP 562XPG Engine Guide bar and saw chain combinations Saw chain filing and file gaugesEN ISO 121002010, ISO 149822009, EN ISO EC Declaration of ConformityApplies to Europe only Page Page Original instructions 1156729-26

560XPG, 560XP, 556, 562XPG, 562XP specifications

The Husqvarna 562XPG, 555, 560XP, 562XP, and 560XPG are part of Husqvarna’s acclaimed line of professional chainsaws known for their power, efficiency, and ergonomic design. Each model caters to the specific needs of forestry professionals, loggers, and serious outdoor enthusiasts.

Starting with the Husqvarna 562XPG, this chainsaw is designed for high-performance cutting in demanding conditions. It features a powerful and efficient X-Torq engine that delivers high torque over a wide RPM range, reducing fuel consumption and emissions. The 562XPG also includes heated handles, which provide additional comfort during cold weather operations. This model is equipped with the AutoTune technology that automatically adjusts the engine settings to varying conditions, ensuring optimal performance without the need for manual tuning.

Next in line is the Husqvarna 555, a robust chainsaw that strikes a balance between power and weight. It is also equipped with the X-Torq engine, making it both fuel-efficient and environmentally friendly. The 555 features an innovative air injection system that removes large debris particles before they enter the air filter, ensuring a longer air filter life and reliable performance. Its lightweight design and excellent balance make it easy to control, even during extended use.

The Husqvarna 560XP is another powerful option, particularly favorable for tree cutting and harvesting. It boasts a professional-grade engine with a higher RPM capacity and advanced air management, maximizing efficiency and cutting speed. Its ergonomic design incorporates features like a low-vibration system and an adjustable oil pump, which improves user comfort and allows for optimal chain lubrication.

The 562XP is similar to the 562XPG but without the heated handles, providing an excellent choice for users who prioritize performance in milder climates. Its lightweight construction coupled with a slim design enhances maneuverability, making it ideal for both professional use and meticulous backyard projects.

Lastly, the Husqvarna 560XPG combines the features of the XP models with the added benefit of heated handles. This saw is engineered for rigorous tasks, featuring robust construction and advanced features like the LowVib system that effectively reduces vibrations. This model is well-suited for those who face harsh weather conditions, ensuring maximum comfort and efficiency in the field.

Collectively, these Husqvarna models represent the pinnacle of modern chainsaw technology, showcasing features that emphasize performance, user comfort, and reliability for all kinds of challenging cutting tasks. Whether you are a professional logger or a passionate homeowner, there is a Husqvarna model to meet your needs.
Top Page Image Contents