Husqvarna 355FXT, 355RX manual Shredding dense vegetation with a shredder blade, Cutting, Sweeping

Husqvarna 355FXT, 355FRM manual 355RX Husqvarna 355RX, 355FXT, 355FRM manual Fitting other guards and cutting attachments Husqvarna 355FRM, 355RX, 355FXT Adjusting the harness and brush cutter, Triobalance harness, Safety release, Correct height Husqvarna 355RX, 355FXT, 355FRM manual Correct balance, Grass clearing Husqvarna 355FXT, 355RX, 355FRM manual Fuel Handling, Fuel safety Husqvarna 355RX, 355FXT, 355FRM manual Fuelling, Mixing Husqvarna 355FRM, 355RX, 355FXT manual Starting and Stopping, Check before starting, Starting and stopping, Cold engine Husqvarna 355RX, 355FXT, 355FRM manual Warm engine, Starting, Stopping, Heated handles Husqvarna 355FXT, 355RX, 355FRM manual Working Techniques, General working instructions, Basic safety rules, ABC of clearing Husqvarna 355RX, 355FXT, 355FRM manual Working Techniques Husqvarna 355FRM, 355RX, 355FXT manual Forestry clearing using a saw blade Husqvarna 355RX Brush cutting with a saw blade, Grass clearing using a grass blade, Grass trimming with a trimmer head
Husqvarna 355FXT, 355RX, 355FRM manual Shredding dense vegetation with a shredder blade, Cutting, Sweeping
Husqvarna 355RX, 355FXT, 355FRM manual Maintenance, Carburettor
Husqvarna 355FRM, 355RX, 355FXT manual Muffler, Cooling system, Air filter, Is damaged it should be replaced
Husqvarna 355RX, 355FXT, 355FRM manual Bevel gear, Drive shaft, Spark plug
Husqvarna 355FXT, 355RX, 355FRM manual Winter use, Temperature 0C or colder, Temperature -5C or colder
Husqvarna 355RX, 355FXT, 355FRM manual Maintenance
Husqvarna 355FRM, 355RX, 355FXT manual Maintenance schedule, Maintenance Daily Weekly Monthly
Husqvarna 355RX, 355FXT, 355FRM manual Technical Data, Technical data
Husqvarna 355FXT, 355RX, 355FRM manual Centre hole in blades/cutters, Ø 25,4 mm
Husqvarna 355RX, 355FXT, 355FRM manual EC-declaration of conformity Applies to Europe only
Husqvarna 355FRM, 355RX, 355FXT manual Trimmy SII
Husqvarna 355RX, 355FXT, 355FRM manual Husqvarna 355FXT, 355RX, 355FRM manual Auto Husqvarna 355RX, 355FXT, 355FRM manual T45, T45x Husqvarna 355FRM, 355RX, 355FXT manual T55x Husqvarna 355RX, 355FXT, 355FRM manual Original instructions 1153302-26
Page 29

WORKING TECHNIQUES

•When trimming and clearing you should use less than full throttle so that the cord lasts longer and to reduce the wear on the trimmer head.

Cutting

•The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.

•Do not allow the trimmer head to constantly come into contact with the ground during normal cutting. Constant contact of this type can cause damage and wear to the trimmer head.

Sweeping

•The fan effect of the rotating cord can be used for quick and easy clearing up. Hold the cord parallel to and above the area to be swept and move the tool to and fro.

•When cutting and sweeping you should use full throttle to obtain the best results.

Shredding dense vegetation with a shredder blade

•The brush cutter is used to ”shred” vegetation, i.e. by woking it up and down through dense grass and brush.

•The shredder blade must not be used on vegetation with a stem diameter larger than 2 cm.

English – 29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents 355FX 355FXT 355RX 355FRM Symbols KEY to SymbolsContents Dear Customer IntroductionWhat is what on the brush cutter? 355RX What is WHAT?What is what on the brush cutter? 355FX, 355FXT What is what on the brush cutter? 355FRM Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipmentCutting attachment guard Stop switchVibration damping system Quick releaseLocking nut MufflerLocking screw Cutting equipmentCutting equipment General rulesSharpening the saw blade Sharpening grass cutters and grass bladesBent, twisted, cracked, broken or To straighten a twisted blade so that itTrimmer head Assembling the handlebar and throttle AssemblyTransport position, handlebar Assembling the cutting equipment355FX, 355FXT Fitting the blade guard and saw blade355RX Fitting other guards and cutting attachments Safety release Adjusting the harness and brush cutterAdjusting the harness Triobalance harnessGrass clearing Correct balanceFuel Fuel safetyFuel Handling Mixing FuellingCheck before starting Starting and StoppingStarting and stopping Cold engineStarting Warm engineStopping Heated handlesWorking Techniques Basic safety rulesGeneral working instructions ABC of clearingWorking Techniques Forestry clearing using a saw blade Brush cutting with a saw blade Grass clearing using a grass bladeGrass trimming with a trimmer head TrimmingSweeping Shredding dense vegetation with a shredder bladeCutting Carburettor MaintenanceCooling system MufflerAir filter Is damaged it should be replacedSpark plug Bevel gearDrive shaft Winter use Temperature 0C or colderTemperature -5C or colder Maintenance Maintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataCentre hole in blades/cutters, Ø 25,4 mm EC-declaration of conformity Applies to Europe only Trimmy SII Page Auto T45, T45x T55x Original instructions 1153302-26
Related manuals
Manual 92 pages 53.47 Kb
Top Page Image Contents