Husqvarna 143R-II manual Maintenance schedule, Daily, Weekly, Monthly, maintenance

Page 25
Maintenance schedule

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorised service workshop.

Maintenance

Daily

 

Weekly

Monthly

maintenance

maintenance

maintenance

 

 

 

 

 

 

Clean the outside of the machine.

 

X

 

 

 

 

 

 

 

Check that the harness is not damaged.

 

X

 

 

 

 

 

 

 

Make sure the throttle trigger lock and the throttle function

 

X

 

 

correctly from a safety point of view.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the handle and handlebar are undamaged and

 

X

 

 

secured correctly.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the stop switch works correctly.

 

X

 

 

 

 

 

 

 

Check that the cutting attachment does not rotate at idle.

 

X

 

 

 

 

 

 

 

Clean the air filter. Replace if necessary.

 

X

 

 

 

 

 

 

 

Check that the guard is undamaged and not cracked. Replace

 

X

 

 

the guard if it has been exposed to impact or is cracked.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the blade is correctly centred, is sharp, and is not

 

 

 

 

cracked. An off-centre blade will cause vibration that could result

 

X

 

 

in damage to the machine.

 

 

 

 

 

 

 

 

 

Check that the trimmer head is undamaged and not cracked.

 

X

 

 

Replace the trimmer head if necessary.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the locking nut of the cutting equipment is tighten

 

X

 

 

correctly.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the transport guard for the blade is intact and that it

 

X

 

 

can be secured correctly.

 

 

 

 

 

 

 

 

 

 

 

 

Check that nuts and screws are tight.

 

X

 

 

 

 

 

 

 

Check that there are no fuel leaks from the engine, tank or fuel

 

X

 

 

lines.

 

 

 

 

 

 

 

 

 

 

 

 

Check the starter and starter cord.

 

 

X

 

 

 

 

 

 

Check that the vibration damping elements are not damaged.

 

 

X

 

 

 

 

 

 

Clean the outside of the spark plug. Remove it and check the

 

 

 

 

electrode gap. Adjust the gap to 0,6-0,7 mm or replace the spark

 

 

X

 

plug. Check that the spark plug is fitted with a suppressor.

 

 

 

 

 

 

 

 

 

Clean the machine’s cooling system.

 

 

X

 

 

 

 

 

 

Clean the outside of the carburettor and the space around it.

 

 

X

 

 

 

 

 

 

Check that the bevel gear is filled three-quarters full with

 

 

X

 

lubricant. Fill if necessary using special grease.

 

 

 

 

 

 

 

 

 

 

 

 

Clean the muffler.

 

 

 

X

 

 

 

 

 

Check the fuel filter from contamination and the fuel hose from

 

 

 

X

cracks or other defects. Replace if necessary.

 

 

 

 

 

 

 

 

 

 

 

 

Check all cables and connections.

 

 

 

X

 

 

 

 

 

Check the clutch, clutch springs and the clutch drum for wear.

 

 

 

X

Replace if necessary by an autorized service workshop.

 

 

 

 

 

 

 

 

 

 

 

 

Replace the spark plug. Check that the spark plug is fitted with a

 

 

 

X

suppressor.

 

 

 

 

 

 

 

 

 

 

 

 

English – 25

Image 25
Contents Page Symbols KEY TO SYMBOLSThe operator of the machine must ensure, while working, that noContents CONTENTSKEY TO SYMBOLS CONTENTSINTRODUCTION What is what on the brushcutter? WHAT IS WHAT?WARNING! Listen out for warning signals GENERAL SAFETY PRECAUTIONSPersonal protective equipment WARNING! The ignition system of thisThrottle lockout Machine′s safety equipmentWARNING! Never use a machine with Cutting attachment guard Stop switchVibration damping system WARNING! Never use a cuttingMuffler Quick releaseLocking nut WARNING! The inside of the mufflerCutting equipment WARNING! Using an incorrect cuttingCutting equipment Sharpening grass cutters and grass bladesTrimmer head Connecting throttle cable and stop switch wires ASSEMBLYFitting the main body Assembling the handlebar and throttle1-2mm Fitting blades and trimmer headsFitting the trimmer guard and trimmer head Fitting the guard extensionG E F D B C H L M C BA AM LWARNING! When using a clearing saw it Adjusting the harness and clearing sawFitting the transport guard Standard harnessWARNING! Take care when handling fuel Fuel safetyFUEL HANDLING FuelFuelling precautions, will lessen the risk of fireMixing WARNING! Taking the followingCheck before starting STARTING AND STOPPINGStarting and stopping StartingStopping WARNING! When the engine is startedstarter cord around your hand WORKING TECHNIQUES Basic safety rulesGeneral working instructions WARNING! Neither the operator of theBasic working techniques Grass clearing using a grass bladeGrass trimming with a trimmer head WARNING! Sometimes branches orSweeping CuttingAdjusting the idle speed T MAINTENANCECarburettor MufflerAir filter Cleaning the air filterFuel filter Bevel gearMaintenance Maintenance schedulemaintenance DailyTechnical data TECHNICAL DATATechnical data WeightEC-declarationof conformity Approved accessoriesApplies to Europe only TypePage Clic 8,5 m 28 10 cm 4,2 m15 cm 2,4-2,7 mm095-.106 2,4-2,7mm4,25 m 8,5 m 28 10 cm 4,3 m T35, T35x10 m 32 10 cm 4,3 m T45, T45x2,7-3,3 mm A 2,7 - 4,0 mm T55xB 8 m / 26’ C 15 cm095-.130 Trimmy SII7,0 m 12 cm