Husqvarna 143R-II Fitting blades and trimmer heads, Assembly, 1-2mm, WARNING! Never use a cutting

Ad

Page 13

1-2mm

ASSEMBLY

and the cable position keep 1-2mm play between the cable lug and the slotted ﬁtting when the throttle trigger is fully depressed.

1-2mm

7When the throttle cable is adjusted correctly, tighten the lock-nut (F) and the M3 screw (G).

8Plug the stop switch wires (H) into the matching connectors from the engine. Note that wire polarity is not important.

9Lap and ﬁx the stop switch wires and connectors with clamp (I).

10 Fit the dust cover (J).

11 Reﬁt the air ﬁlter cover.

Fitting blades and trimmer heads

WARNING!

! When ﬁtting the cutting attachment it is extremely important that the raised section on the drive disc/support ﬂange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is ﬁtted incorrectly it can result in serious and/or fatal personal injury.

WARNING! Never use a cutting

! attachment without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is ﬁtted this can cause serious personal injury.

IMPORTANT! If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar, blade guard and harness.

English – 13

Image 13

Contents Page Symbols KEY TO SYMBOLSThe operator of the machine must ensure, while working, that noContents CONTENTSKEY TO SYMBOLS CONTENTSINTRODUCTION What is what on the brushcutter? WHAT IS WHAT?WARNING! Listen out for warning signals GENERAL SAFETY PRECAUTIONSPersonal protective equipment WARNING! The ignition system of thisThrottle lockout Machine′s safety equipmentWARNING! Never use a machine with Cutting attachment guard Stop switchVibration damping system WARNING! Never use a cuttingMufﬂer Quick releaseLocking nut WARNING! The inside of the mufﬂerCutting equipment WARNING! Using an incorrect cuttingCutting equipment Sharpening grass cutters and grass bladesTrimmer head Connecting throttle cable and stop switch wires ASSEMBLYFitting the main body Assembling the handlebar and throttle1-2mm Fitting blades and trimmer headsFitting the trimmer guard and trimmer head Fitting the guard extensionG E F D B C H L M C BA AM LWARNING! When using a clearing saw it Adjusting the harness and clearing sawFitting the transport guard Standard harnessWARNING! Take care when handling fuel Fuel safetyFUEL HANDLING FuelFuelling precautions, will lessen the risk of ﬁreMixing WARNING! Taking the followingCheck before starting STARTING AND STOPPINGStarting and stopping StartingStopping WARNING! When the engine is startedstarter cord around your hand WORKING TECHNIQUES Basic safety rulesGeneral working instructions WARNING! Neither the operator of theBasic working techniques Grass clearing using a grass bladeGrass trimming with a trimmer head WARNING! Sometimes branches orSweeping CuttingAdjusting the idle speed T MAINTENANCECarburettor MufﬂerAir ﬁlter Cleaning the air ﬁlterFuel ﬁlter Bevel gearMaintenance Maintenance schedulemaintenance DailyTechnical data TECHNICAL DATATechnical data WeightEC-declarationof conformity Approved accessoriesApplies to Europe only TypePage Clic 8,5 m 28 10 cm 4,2 m15 cm 2,4-2,7 mm095-.106 2,4-2,7mm4,25 m 8,5 m 28 10 cm 4,3 m T35, T35x10 m 32 10 cm 4,3 m T45, T45x2,7-3,3 mm A 2,7 - 4,0 mm T55xB 8 m / 26’ C 15 cm095-.130 Trimmy SII7,0 m 12 cm