Lincoln Electric IM871-A manual Before Starting the Engine

Page 19

B-4

OPERATION

B-4

BEFORE STARTING THE ENGINE

CHECK AND FILL THE ENGINE OIL LEVEL:

1. Place the machine on a level surface.

2.Open the oil fill plug.

3.Fill (if necessary) until oil flows out the top of the fill plug hole.

4.Replace the fill plug and tighten securely.

CHECK AND FILL THE ENGINE FUEL TANK:

1. Remove the fuel tank cap.

2. Fill the tank to allow approximately 1/4 inch (5 mm) of tank space for fuel expansion. DO NOT FILL THE TANK TO THE POINT OF OVERFLOW.

3. Replace the fuel tank cap and tighten securely.

NOTE: The engine will operate satisfactorily on any gasoline meant for automotive use. A mini- mum of 87 octane is recommended. DO NOT MIX OIL WITH THE GASOLINE.

Use clean, fresh, lead-free gasoline. Leaded gasoline may be used if lead-free is not available. However, lead-free gasoline leaves fewer combustion deposits and gives longer valve life. Purchase gasoline in quantities that will be used within 30 days, to assure freshness.

NOTE: We DO NOT recommend using gasoline that contains alcohol, such as gasohol. However, if gasoline with alcohol is used, it MUST NOT contain more than 10% Ethanol and MUST be removed from the engine during storage. DO NOT use gasoline containing Methanol.

STARTING THE ENGINE

NOTE: Remove all loads connected to the AC power receptacles before starting the gasoline engine. Put the “ON/OFF” Switch in the “ON”(I) position.

FOR A “COLD” ENGINE:

1. Open the fuel shutoff valve.

2. Place the choke lever in the “CHOKE” position.

3.Pull slightly on the recoil starter handle until resis- tance is felt.

4.Pull the cord rapidly.

5.If the engine does not start, open the choke slightly and pull the starter cord rapidly again.

When the engine starts, gradually open the choke to the “RUN” position. To open the choke fully requires an engine warm-up period of several seconds to several minutes, depending on the temperature. After starting the engine, first open the choke (toward RUN) until the engine just begins to run smoothly. Then open the choke in small steps, allowing the engine to accept small changes in speed and load, until the choke is fully open (in RUN). During engine warm-up the equip- ment can be operated.

FOR A “HOT” ENGINE:

1.Open the fuel shutoff valve.

2.Place the choke lever in the “RUN”

position. Closing the choke of a hot engine will flood the carburetor and prevent starting.

3.Pull slightly on the recoil starter handle until resis- tance is felt.

4.Pull the cord rapidly.

FOR BEST ENGINE STARTING:

•Always use fresh gasoline and be sure the filter is clean and properly maintained.

•If you use an alternate fuel tank or supply, be sure to install an in-line fuel filter.

•Do not pull the recoil starter with the

choke in the “CHOKE” position more than one time. Repeated pulls on a choked engine will flood the carbure- tor.

•If the engine will not start, see the T R O U - BLE SHOOTI NG section of this or the engine owner’s manual.

POWER-ARC 5500

Page 18 Page 20
Image 19
Page 18 Page 20
Contents POWER-ARC California Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding and Cutting Sparks can Cause fire or explosionPrécautions DE Sûreté On-Line Product Registration Please Examine Carton and Equipment For Damage ImmediatelyTable of Contents Technical Specifications POWER-ARC InstallationEngine Exhaust can kill Safety PrecautionsLocation and Ventilation StoringGasoline Fuel only PRE-OPERATION Engine ServiceHonda 9 HP PowerArc 5500 Typical Fuel ConsumptionMuffler Deflector Spark ArresterCable Size and Length POWER-ARC 5500 Output ConnectionsElectrical Output Connections Welding Cable ConnectionsMachine Grounding Auxiliary Power ReceptaclesCable Installation Plugs and HAND-HELD EquipmentCircuit Breakers Premises WiringType Common Electrical Devices Possible Concerns Table A.2 Electrical Device USE with the POWER-ARCOperation Physical Location of Components may vary by Code No Controls and SettingsLimitations Output Panel ControlsGasoline Engine Controls Engine OperationStarting the Engine Before Starting the EngineBREAK-IN Period Generator OperationStopping the Engine Running the EngineTable B.3 Generator Power Applications Control Function / Operation Current Control Dial Welding OperationWelding Guidelines Material Thickness Electrode Type Size SettingWelding arc What Happens in the Arc?Correct Welding Speed Correct Welding PositionCorrect Way to Strike An Arc Correct Arc LengthDo the following Common MetalsTypes of Welds Use the followingWelding in the Vertical Position Fillet JointsPenetration Multiple Pass WeldsVertical-Down Welding Vertical-Up WeldingHardfacing To Reduce Wear How to Hardface the Sharp Edge Metal to Ground WearOverhead Welding Welding Sheet MetalCast Iron Plate Preparation Welding Cast IronOut-of-Position Group AWS E6011 High-Speed Group AWS E6013 Selecting ElectrodesLow Hydrogen Group AWS E7018 OPTIONS/ACCESSORIES AccessoriesLincoln Electric Accessories Routine and Periodic Maintenance MaintenanceEngine Maintenance Figure D.3 Clean Rotating SCREEN/FINGER GUARD/DEBRIS Guard Engine AdjustmentsPart Robin / Subaru Honda Table D.1 Engine Maintenance PartsFigure D.5. Brush Removal and Replacement GENERATOR/WELDER MaintenanceFigure D.6. Major Component Locations HOW to USE Troubleshooting Guide TroubleshootingContact your local Lincoln Authorized Field Service Facility SymptomsTroubleshooting Engine requires service to head, head gasket, and/or valves Enhanced Diagram DiagramsDiagrams Diagrams Diagrams Power ARC Print Dimension Page Precaucion Guards off

IM871-A specifications

The Lincoln Electric IM871-A is a cutting-edge industrial welding machine that exemplifies the brand's commitment to quality, innovation, and efficiency. Designed specifically for professionals in various sectors, including manufacturing, construction, and maintenance, the IM871-A boasts a range of features that streamline the welding process while ensuring longevity and reliability.

One of the standout features of the IM871-A is its advanced inverter technology. This technology not only enhances the machine’s portability but also improves energy efficiency. The inverter design allows for a compact and lightweight unit without sacrificing power output, making it easier for welders to move around job sites while maintaining peak performance. Welders can expect to achieve high-quality welds with minimal spatter, ensuring a clean and professional finish.

The IM871-A is equipped with a multifunctional interface, allowing users to easily navigate through various settings and customize their welding parameters according to specific project requirements. This user-friendly display includes digital readouts for voltage and current, providing real-time information that aids in precision control. Such adaptability makes the IM871-A suitable for a wide range of welding applications, from thin sheet metal to heavier structural components.

Additionally, the Lincoln Electric IM871-A supports multiple welding processes, including MIG, TIG, and Stick welding. This versatility makes it an ideal choice for professionals who require a machine that can handle diverse tasks without the need for multiple setups or equipment. The welder's robust output range further enhances its capabilities, accommodating various materials and thicknesses for both ferrous and non-ferrous metals.

Safety is paramount in any welding operation, and the IM871-A incorporates several features designed to protect the user. These include built-in thermal overload protection, which prevents the machine from overheating during extended use, and an automatic voltage reduction system that ensures the welder remains safe while efficiently managing power.

In summary, the Lincoln Electric IM871-A is a powerful and versatile welding machine built to meet the rigorous demands of industrial applications. With its advanced inverter technology, intuitive user interface, multiple welding process support, and essential safety features, it stands out as a reliable choice for professionals aiming for quality and efficiency in their welding operations. Whether for onsite applications or workshop environments, the IM871-A is engineered to deliver exceptional performance and durability, solidifying its place in the competitive welding market.
Top Page Image Contents