Panasonic M282737F owner manual Step Twelve Check and test completed assembly, Test with water

Page 16

Assembly (continued)

10.To disconnect permanently

When it is necessary to disconnect the sprayer’s battery power cord from the battery, use the following procedure:

1.Disconnect sprayer’s remote switch power cord from the battery power cord.

2.Disconnect the battery power cord from the vehicle battery as follows:

a)Disconnect vehicle battery ground wire.

b)Disconnect the battery cord’s black battery clamp or black wire

connector from the negative(-)terminal of the vehicle battery.

c)Disconnect the battery cord’s red battery clamp or red wire connector from the positive(+) terminal of the vehicle battery.

d)Reconnect the vehicle battery ground wire.

WARNING: Always connect in this sequence to avoid possible shock.

Step Twelve: Check and test completed assembly.

WARNING

Check and test completed assembly

Serious injury could result from chemical leaks if sprayer is improperly assembled or the design of the sprayer is modified.

Follow the steps below to ensure the sprayer is properly assembled. Never modify the sprayer design.

1. Check assembly

Check assembly to assure the sprayer is properly assembled and in safe working condition:

a)Check that the gun clip screws are tight, hose clamps are secure, and tank straps are properly fastened.

b)While it is unlikely that factory assembled components become loose, they should also be checked to make sure they aretight.

2. Test with water

Test the system for leaks with water:

1)First read the instructions in this Owner’s Manual for Operation of the sprayer

2)Fill the tank with water per the instructions in this manual. Important: The sprayer should be OFF when you fill the tank.

3)Check for leaks throughout the system by operating the sprayer per the instructions in this manual:

a)Turn the sprayer ON. (See Operation Instructions)

b)Operate the spray gun. (See Operation Instructions)

c)Adjust the pressure through its full range – to maximum and back. (See Operation Instructions)

4)If a leak is detected, fix the leak and re-test the system with water.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents M282737F Hazard Signal Word Definitions Table of Contents Intended Use Spraying PesticidesSummary of Important Safety Information During AssemblyGeneral Chemical Safety Chemical Application SafetyChemical accident procedures InhalationDifferently with filled sprayer attached Closely inspect all contents in the shipping carton UnpackingUnpacking the Manual Bag Following items are found in the manual bagAssembly Step One Attach the tongue to the cart baseStep Two Attach the hitch mount to the tongue Step Three Attach the cart base to the sprayerStep Five Attach pressure gauge Step Four Attach wheels to cart baseStep Six Attach gun hose to spray gun and pump Step Eight Attach drain cap to tank Step Seven Attach gun clips to tankStep Nine Attach hose guide to tank Preparatory safety Preparatory safety steps Step Eleven Connect power cords to vehicle batteryStep Ten Attach sprayer to vehicle Separate power Prepare wire endsVehicle battery To install battery clampsAttach remote switch Power cord may remain connected to the batteryStep Twelve Check and test completed assembly Check and test completed assemblyTest with water Test the system for leaks with waterMachine Components Operation Important Safety Information General Chemical SafetyChemical Application Safety Before SprayingDuring Spraying After SprayingTowing Safety Inhalation Operation Preparing the Sprayer for Each Use Important safety rulesInspect Inspect and test the sprayer thoroughly Repair Step One Assess wind conditions and clear work area Operation Using the SprayerSpray because the wind is too strong Step Two Fill the sprayer Ensure tank is flushed of all chemicals from prior usesCheck drain Fill tankReview safety Step Three Operate the sprayerEnsure flow Through priming HoseProper Operation of the Spray Gun Operate spray gun as needed for applicationOpen until desired amount of agitation is achieved ImmediatelyStep Four Clean sprayer and decontaminate after use Drain tankDecontaminate LaunderStorage Troubleshooting Before attempting to service the sprayerSpecifications Any Questions, Comments, Problems or Parts OrdersAny Questions, Comments, Problems or Parts Orders Exploded View 282737 Rev. F

M282737F specifications

Panasonic has long been a key player in the electronics industry, providing innovative products that meet diverse consumer needs. One of their notable offerings is the Panasonic M282737F, a versatile and efficient device that showcases the company's commitment to quality and advanced technology.

The M282737F is designed primarily for industrial applications, catering to sectors that require reliable and high-performance solutions. Its standout feature is its robust construction, which ensures durability in demanding environments. This makes it an ideal choice for factories, warehouses, and other industrial settings where equipment faces wear and tear.

At the heart of the M282737F is Panasonic's cutting-edge technology, which includes enhanced energy efficiency capabilities. This device is engineered to minimize power consumption while maintaining optimal performance, thus reducing operational costs for businesses. These efficiency measures align with global efforts toward sustainability, making the M282737F a responsible choice for environmentally conscious companies.

In terms of usability, the M282737F offers intuitive controls and a user-friendly interface, allowing operators to seamlessly integrate it into their existing workflows. Its compatibility with various systems and platforms further enhances its versatility, ensuring that it can function effectively within diverse operational contexts. This interoperability means that users can leverage nostalgic legacy systems while also preparing for future advancements.

Additionally, safety features are paramount in the design of the M282737F. It is equipped with multiple safeguards that protect against overload and short circuits, ensuring a high level of reliability in critical applications. These built-in safety mechanisms also provide peace of mind to operators who depend on the device for their daily operations.

Another noteworthy characteristic of the M282737F is its compact and lightweight design. This factor not only makes it easier to install but also allows for flexibility in deployment, particularly in spaces where every square inch is valuable.

In summary, the Panasonic M282737F stands out as a prime example of the company's dedication to engineering excellence, energy efficiency, and user-friendly design. With its robust features, advanced technologies, and safety mechanisms, it is a worthy investment for any industrial operation looking to enhance productivity and reliability in their equipment.
Top Page Image Contents