Panasonic M282737F owner manual Chemical accident procedures, Inhalation

Page 6

Summary of Important Safety Information (continued)

TURN OFF vehicle and set brake or block wheels, TURN OFF power to sprayer, and RELIEVE system pressure before leaving sprayer unattended.

SEE Troubleshooting section of this manual before attempting any repairs. Wear personal protective equipment and follow safety instructions.

After Spraying

CLEAN sprayer immediately after use according to the directions provided in this manual.

DECONTAMINATE yourself after you are done spraying and have cleaned the sprayer. Wash all exposed areas of the body with soap and water, and remove and launder clothing.

DISPOSE OF or STORE remaining chemicals in secure storage with correctly marked container.

Towing Safety

READ towing safety instructions in your towing vehicle manual.

DO NOT ALLOW drivers younger than 16 to operate the towing vehicle with the filled sprayer attached.

MAKE SURE SPRAYER IS SECURELY ATTACHED to vehicle.

EXERCISE CAUTION in vehicle handling when towingfilled sprayer to avoid loss of control or overturning. o Keep speed to a minimum so you can maintain control. Reduce speed prior to turns.

o Allow for wider turns and for more distance to stop.

o Avoid any sudden steering maneuvers, starts, or stops that could create sway.

SLOW DOWN and EXERCISE EXTRA CAUTION on sloped or uneven terrain. Pick the most level route possible. Drive up and down slopes when necessary, rather than across. Use a vehicle equipped with a roll over protection system (ROPS) if you will be working on non-level terrain.

BE AWARE of the added length of the sprayer, visibility may be reduced when making turns or backing up.

DO NOT RIDE or TRANSPORT cargo on the sprayer.

COMPLY WITH all local, state, and federal towing requirements if you will be towing on public roads.

TURN OFF both sprayer and vehicle, and SET BRAKES or BLOCK WHEELS before leaving unattended.

Chemical accident procedures

Immediate response is necessary in the event of sprayer leaks, bodily chemical contact, poisoning, or spills.

Sprayer leak

If the sprayer develops a leak, immediately stop spraying. Turn off power to the

 

sprayer and follow directions below, as applicable.

Bodily chemical

Personal contamination can occur when chemicals splash, spill, or spray

contact

directly onto a person.

 

1.

Immediately follow First Aid instructions on chemical label.

 

 

General procedures can include:

 

 

a) Eyes – immediately flush with water.

 

 

b) Skin – wash all contaminated skin surfaces with soap and water.

 

 

c) Clothing – remove contaminated clothing. Dispose of heavily

 

 

contaminated clothing per chemical label instructions.

 

2.

Seek medical advice if instructed on the label or the victim experiences

 

 

symptoms of harmful effects. Bring the chemical label for reference.

Poisoning by

In case of poisoning from ingestion or inhalation:

ingestion or

If the victim has collapsed or is not breathing, call 911. Otherwise:

inhalation

1. If you are the victim, immediately seek assistance from nearby personnel

 

 

because you may become incapacitated.

 

2.

Immediately follow first aid instructions on chemical label.

 

3.

Call a poison control center for further advice. In the U.S., call 1-800-222-1222.

 

 

Have the chemical label available for reference.

Chemical spills

Chemical spills must be quickly contained and properly cleaned up.

 

Refer to the chemical label for any specific clean-up instructions.

 

General procedures include:

 

1.

Controlling the spill by stopping the source of the spill.

 

2.

Containing the spill so that it does not spread and get into water sources.

 

3.

Cleaning up the spill immediately.

 

4.

Seeking additional advice from:

 

 

- Chemical manufacturer. See chemical label for contact information.

 

 

- State pesticide regulatory agency. In the U.S., call the National Pesticide Info.

 

 

Ctr. at 800-858-7378 for assistance in contacting your state’s agency.

6

Image 6
Contents M282737F Hazard Signal Word Definitions Table of Contents Intended Use Spraying PesticidesGeneral Chemical Safety Summary of Important Safety InformationDuring Assembly Chemical Application SafetyChemical accident procedures InhalationDifferently with filled sprayer attached Closely inspect all contents in the shipping carton UnpackingUnpacking the Manual Bag Following items are found in the manual bagStep Two Attach the hitch mount to the tongue AssemblyStep One Attach the tongue to the cart base Step Three Attach the cart base to the sprayerStep Four Attach wheels to cart base Step Five Attach pressure gaugeStep Six Attach gun hose to spray gun and pump Step Seven Attach gun clips to tank Step Eight Attach drain cap to tankStep Nine Attach hose guide to tank Step Eleven Connect power cords to vehicle battery Preparatory safety Preparatory safety stepsStep Ten Attach sprayer to vehicle Vehicle battery Separate powerPrepare wire ends To install battery clampsAttach remote switch Power cord may remain connected to the batteryTest with water Step Twelve Check and test completed assemblyCheck and test completed assembly Test the system for leaks with waterMachine Components Operation Important Safety Information General Chemical SafetyDuring Spraying Chemical Application SafetyBefore Spraying After SprayingTowing Safety Inhalation Important safety rules Operation Preparing the Sprayer for Each UseInspect Inspect and test the sprayer thoroughly Repair Operation Using the Sprayer Step One Assess wind conditions and clear work areaSpray because the wind is too strong Step Two Fill the sprayer Ensure tank is flushed of all chemicals from prior usesCheck drain Fill tankEnsure flow Review safetyStep Three Operate the sprayer Through priming HoseProper Operation of the Spray Gun Operate spray gun as needed for applicationOpen until desired amount of agitation is achieved ImmediatelyDecontaminate Step Four Clean sprayer and decontaminate after useDrain tank LaunderStorage Troubleshooting Before attempting to service the sprayerSpecifications Any Questions, Comments, Problems or Parts OrdersAny Questions, Comments, Problems or Parts Orders Exploded View 282737 Rev. F

M282737F specifications

Panasonic has long been a key player in the electronics industry, providing innovative products that meet diverse consumer needs. One of their notable offerings is the Panasonic M282737F, a versatile and efficient device that showcases the company's commitment to quality and advanced technology.

The M282737F is designed primarily for industrial applications, catering to sectors that require reliable and high-performance solutions. Its standout feature is its robust construction, which ensures durability in demanding environments. This makes it an ideal choice for factories, warehouses, and other industrial settings where equipment faces wear and tear.

At the heart of the M282737F is Panasonic's cutting-edge technology, which includes enhanced energy efficiency capabilities. This device is engineered to minimize power consumption while maintaining optimal performance, thus reducing operational costs for businesses. These efficiency measures align with global efforts toward sustainability, making the M282737F a responsible choice for environmentally conscious companies.

In terms of usability, the M282737F offers intuitive controls and a user-friendly interface, allowing operators to seamlessly integrate it into their existing workflows. Its compatibility with various systems and platforms further enhances its versatility, ensuring that it can function effectively within diverse operational contexts. This interoperability means that users can leverage nostalgic legacy systems while also preparing for future advancements.

Additionally, safety features are paramount in the design of the M282737F. It is equipped with multiple safeguards that protect against overload and short circuits, ensuring a high level of reliability in critical applications. These built-in safety mechanisms also provide peace of mind to operators who depend on the device for their daily operations.

Another noteworthy characteristic of the M282737F is its compact and lightweight design. This factor not only makes it easier to install but also allows for flexibility in deployment, particularly in spaces where every square inch is valuable.

In summary, the Panasonic M282737F stands out as a prime example of the company's dedication to engineering excellence, energy efficiency, and user-friendly design. With its robust features, advanced technologies, and safety mechanisms, it is a worthy investment for any industrial operation looking to enhance productivity and reliability in their equipment.