Panasonic M282737F Operation Preparing the Sprayer for Each Use, Important safety rules

Page 22

Operation – Preparing the Sprayer for Each Use

If the sprayer has been used previously, it must be prepared BEFORE EACH SUBSEQUENT USE.

WARNING

Read instructions below carefully for inspecting and preparing the sprayer. Damaged or clogged equipment could result in leaks or uncontrolled spray.

Leaks could result in injury to the operator or bystanders from chemical exposure, or cause damage to the environment.

Important safety rules:

•

•

•

Power off. Make sure all power is OFF before cleaning, inspecting, or servicing the sprayer. Guards / shields. Make sure all guards and shields are replaced after servicing the sprayer. Replacement parts. If a part needs replacement, only use parts that meet the manufacturer’s specifications. Replacement parts that do not meet specifications may result in a safety hazard or poor operation of the sprayer.

1.

Ensure sprayer

Ensure the sprayer is securely attached to the towing vehicle.

 

attached

 

 

2.

Ensure tank

Ensure the sprayer has been thoroughly flushed and drained of all residual

 

empty

chemical from prior uses.

3. Clean suction

Clean the suction strainer of any chemical residue.

 

strainer

It is important to clean the suction strainer before each use to ensure it is not

 

 

clogged and to prevent residual chemical from contaminating sprayer contents.

 

 

IMPORTANT: The strainer must be accessed by reaching into the tank, so the

 

 

tank must be empty to avoid immersing your hand in chemicals.

 

 

a) Open fill cap on top of tank.

 

 

b)

USING RUBBER GLOVES, reach into the tank and pull the suction

 

 

 

strainer off the end of the suction tube. (See figure below.)

 

 

c)

Run the suction strainer under fresh water to remove debris.

 

 

d)

Replace the suction strainer onto the end of the suction tube.

 

 

 

Fill cap

 

 

),*

 

 

Suction strainer

 

 

(Inside tank)

4. Inspect &

Inspect and test the sprayer thoroughly:

repair

a)

Inspect hoses for exposed mesh and holes. Replace all worn or damaged hoses.

 

b)

Inspect tank and fittings for cracks and leaks. Replace all damaged fittings with

 

 

original NorthStar parts.

 

c) Check to be sure all other nuts, bolts, and screws are tight.

 

d)

Check wheels and tires. Make sure wheel lugs are tight and tires are inflated.

 

e) Partially fill tank with plain water and spray to test for leaks. Repair as needed.

 

IMPORTANT: After any repair work has been done, ALWAYS test for leaks

 

with water one final time before using.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents M282737F Hazard Signal Word Definitions Table of Contents Intended Use Spraying PesticidesGeneral Chemical Safety Summary of Important Safety InformationDuring Assembly Chemical Application SafetyChemical accident procedures InhalationDifferently with filled sprayer attached Closely inspect all contents in the shipping carton UnpackingUnpacking the Manual Bag Following items are found in the manual bagStep Two Attach the hitch mount to the tongue AssemblyStep One Attach the tongue to the cart base Step Three Attach the cart base to the sprayerStep Five Attach pressure gauge Step Four Attach wheels to cart baseStep Six Attach gun hose to spray gun and pump Step Eight Attach drain cap to tank Step Seven Attach gun clips to tankStep Nine Attach hose guide to tank Preparatory safety Preparatory safety steps Step Eleven Connect power cords to vehicle batteryStep Ten Attach sprayer to vehicle Vehicle battery Separate powerPrepare wire ends To install battery clampsAttach remote switch Power cord may remain connected to the batteryTest with water Step Twelve Check and test completed assemblyCheck and test completed assembly Test the system for leaks with waterMachine Components Operation Important Safety Information General Chemical SafetyDuring Spraying Chemical Application SafetyBefore Spraying After SprayingTowing Safety Inhalation Operation Preparing the Sprayer for Each Use Important safety rulesInspect Inspect and test the sprayer thoroughly Repair Step One Assess wind conditions and clear work area Operation Using the SprayerSpray because the wind is too strong Step Two Fill the sprayer Ensure tank is flushed of all chemicals from prior usesCheck drain Fill tankEnsure flow Review safetyStep Three Operate the sprayer Through priming HoseProper Operation of the Spray Gun Operate spray gun as needed for applicationOpen until desired amount of agitation is achieved ImmediatelyDecontaminate Step Four Clean sprayer and decontaminate after useDrain tank LaunderStorage Troubleshooting Before attempting to service the sprayerSpecifications Any Questions, Comments, Problems or Parts OrdersAny Questions, Comments, Problems or Parts Orders Exploded View 282737 Rev. F

M282737F specifications

Panasonic has long been a key player in the electronics industry, providing innovative products that meet diverse consumer needs. One of their notable offerings is the Panasonic M282737F, a versatile and efficient device that showcases the company's commitment to quality and advanced technology.

The M282737F is designed primarily for industrial applications, catering to sectors that require reliable and high-performance solutions. Its standout feature is its robust construction, which ensures durability in demanding environments. This makes it an ideal choice for factories, warehouses, and other industrial settings where equipment faces wear and tear.

At the heart of the M282737F is Panasonic's cutting-edge technology, which includes enhanced energy efficiency capabilities. This device is engineered to minimize power consumption while maintaining optimal performance, thus reducing operational costs for businesses. These efficiency measures align with global efforts toward sustainability, making the M282737F a responsible choice for environmentally conscious companies.

In terms of usability, the M282737F offers intuitive controls and a user-friendly interface, allowing operators to seamlessly integrate it into their existing workflows. Its compatibility with various systems and platforms further enhances its versatility, ensuring that it can function effectively within diverse operational contexts. This interoperability means that users can leverage nostalgic legacy systems while also preparing for future advancements.

Additionally, safety features are paramount in the design of the M282737F. It is equipped with multiple safeguards that protect against overload and short circuits, ensuring a high level of reliability in critical applications. These built-in safety mechanisms also provide peace of mind to operators who depend on the device for their daily operations.

Another noteworthy characteristic of the M282737F is its compact and lightweight design. This factor not only makes it easier to install but also allows for flexibility in deployment, particularly in spaces where every square inch is valuable.

In summary, the Panasonic M282737F stands out as a prime example of the company's dedication to engineering excellence, energy efficiency, and user-friendly design. With its robust features, advanced technologies, and safety mechanisms, it is a worthy investment for any industrial operation looking to enhance productivity and reliability in their equipment.
Top Page Image Contents