Panasonic M282737F Proper Operation of the Spray Gun, Operate spray gun as needed for application

Page 27

Operation - Using the Sprayer (continued)

6.Operate spray gun (as needed for application)

Proper Operation of the Spray Gun

Cone and Stream spray pattern instructions

1.Pull the choke back. Squeeze thetrigger to begin spraying.

2.The spray pattern is determined by how far the trigger is pulled back. The spray begins at a wide cone and progressively becomes a straight stream when the trigger is pulled all the way back.

3.Once the desired spray pattern is achieved, press the trigger lock to hold the position of thetrigger. To release thetrigger lock, pull the trigger back until the lock disengages.

4.When the gun is not in use, activate the safety lock by releasing the trigger and pressing the safety lock pin. This will lock thetrigger in the off position to prevent accidental spraying.

Additional orifice and

Trigger lock

spare O-ring storage

Safety lock

 

Choke pulled back

Trigger

Swivel connection

Fog and Stream spray pattern instructions

1.Push the choke all the way forward.

2.Squeeze the trigger to begin spraying. Set thetrigger to a wide cone spray pattern. This will achievethe best atomized mist.

3.Pull the trigger all the way back to change to a straight stream.

Choke pushed forward

Note: Operating pressure of the pump will vary depending on the orifice size used. 110 psi is achieved with the small orifice. The medium and large orifices achieve 50 and 2 psi, respectively. (Additional orifices are located under the yellow plug on the top of the gun.)

IMPORTANT: ALWAYS hold the spray gun with a firm grip when spraying at higher pressures in order to prevent gun from whipping. Keep good footing and balance at alltimes.

Note: It is not unusual for the operator to be exposed to chemical drips while adjusting the spray pattern – gloves should be chemical resistant.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents M282737F Hazard Signal Word Definitions Table of Contents Spraying Pesticides Intended UseChemical Application Safety Summary of Important Safety InformationDuring Assembly General Chemical SafetyInhalation Chemical accident proceduresDifferently with filled sprayer attached Unpacking Closely inspect all contents in the shipping cartonFollowing items are found in the manual bag Unpacking the Manual BagStep Three Attach the cart base to the sprayer AssemblyStep One Attach the tongue to the cart base Step Two Attach the hitch mount to the tongueStep Four Attach wheels to cart base Step Five Attach pressure gaugeStep Six Attach gun hose to spray gun and pump Step Seven Attach gun clips to tank Step Eight Attach drain cap to tankStep Nine Attach hose guide to tank Step Eleven Connect power cords to vehicle battery Preparatory safety Preparatory safety stepsStep Ten Attach sprayer to vehicle To install battery clamps Separate powerPrepare wire ends Vehicle batteryPower cord may remain connected to the battery Attach remote switchTest the system for leaks with water Step Twelve Check and test completed assemblyCheck and test completed assembly Test with waterMachine Components General Chemical Safety Operation Important Safety InformationAfter Spraying Chemical Application SafetyBefore Spraying During SprayingTowing Safety Inhalation Important safety rules Operation Preparing the Sprayer for Each UseInspect Inspect and test the sprayer thoroughly Repair Operation Using the Sprayer Step One Assess wind conditions and clear work areaSpray because the wind is too strong Ensure tank is flushed of all chemicals from prior uses Step Two Fill the sprayerFill tank Check drainThrough priming Hose Review safetyStep Three Operate the sprayer Ensure flowOperate spray gun as needed for application Proper Operation of the Spray GunImmediately Open until desired amount of agitation is achievedLaunder Step Four Clean sprayer and decontaminate after useDrain tank DecontaminateStorage Before attempting to service the sprayer TroubleshootingAny Questions, Comments, Problems or Parts Orders SpecificationsExploded View 282737 Rev. F Any Questions, Comments, Problems or Parts Orders

M282737F specifications

Panasonic has long been a key player in the electronics industry, providing innovative products that meet diverse consumer needs. One of their notable offerings is the Panasonic M282737F, a versatile and efficient device that showcases the company's commitment to quality and advanced technology.

The M282737F is designed primarily for industrial applications, catering to sectors that require reliable and high-performance solutions. Its standout feature is its robust construction, which ensures durability in demanding environments. This makes it an ideal choice for factories, warehouses, and other industrial settings where equipment faces wear and tear.

At the heart of the M282737F is Panasonic's cutting-edge technology, which includes enhanced energy efficiency capabilities. This device is engineered to minimize power consumption while maintaining optimal performance, thus reducing operational costs for businesses. These efficiency measures align with global efforts toward sustainability, making the M282737F a responsible choice for environmentally conscious companies.

In terms of usability, the M282737F offers intuitive controls and a user-friendly interface, allowing operators to seamlessly integrate it into their existing workflows. Its compatibility with various systems and platforms further enhances its versatility, ensuring that it can function effectively within diverse operational contexts. This interoperability means that users can leverage nostalgic legacy systems while also preparing for future advancements.

Additionally, safety features are paramount in the design of the M282737F. It is equipped with multiple safeguards that protect against overload and short circuits, ensuring a high level of reliability in critical applications. These built-in safety mechanisms also provide peace of mind to operators who depend on the device for their daily operations.

Another noteworthy characteristic of the M282737F is its compact and lightweight design. This factor not only makes it easier to install but also allows for flexibility in deployment, particularly in spaces where every square inch is valuable.

In summary, the Panasonic M282737F stands out as a prime example of the company's dedication to engineering excellence, energy efficiency, and user-friendly design. With its robust features, advanced technologies, and safety mechanisms, it is a worthy investment for any industrial operation looking to enhance productivity and reliability in their equipment.
Top Page Image Contents