Panasonic M282737F Chemical Application Safety, Before Spraying, During Spraying, After Spraying

Page 19

Operation – Important Safety Information (continued)

Chemical Application Safety:

WARNING

Caution must be used when spraying chemicals to avoid unsafe exposure to humans and the environment.

Heed the warnings below and follow all instructions carefully.

Before Spraying

•Sprayer prep. ALWAYS inspect and prepare the sprayer before use according to the directions provided in this manual.

•Keep sprayer off. Do not turn on power to the sprayer until ready to spray in order to avoid unintentional spray release.

•Overhead spraying or fogging. Wear additional personal protective equipment if you will be spraying overhead or fogging. You will be exposed to much more pesticide fallout in these applications. Wear chemical resistant head and neck protection, full face mask or half face mask with sealed goggles, and consider using a dust/mist respirator.

•Wind speed. NEVER spray when wind speed exceeds 4 MPH in order to minimize spray drift.

•Clear area/post. ALWAYS keep the work area clear of people and pets. POST warning notices to restrict access by the public for the period recommended on chemical label.

•Operator age. You must be 16 years of age or older to operatethis sprayer. Pesticides are especially toxic to children.

During Spraying

•Overapplication. DO NOT overapply pesticide. Apply at a rate recommended by chemical manufacturer. Excess pesticide can be dangerous to humans, damage desirable plants, and contaminate soil and water sources.

•Never point gun. NEVER point the spray gun at people or animals.

•Use firm grip. ALWAYS hold the spray gun with a firm grip when spraying at higher pressures in order to prevent gun from whipping. Keep good footing and balance at all times.

•Children/pets. ALWAYS exercise extra caution when spraying near areas accessible to children and pets.

•Eating/smoking. DO NOT eat, drink, smoke, rub your eyes, or touch any part of your bare skin while handling chemicals and spraying.

•Heat/flames. DO NOT spray near open flames or sources of heat.

•Spills. ALWAYS clean up spills immediately per instructions on the chemical label.

•Unattended. ALWAYS turn off vehicle and set brake or block wheels, turn off power to sprayer, and relieve system pressure before leaving sprayer unattended.

•Troubleshooting. ALWAYS refer to the safety instructions in theTroubleshooting Section before attempting any repairs.

After Spraying

•Clean sprayer. ALWAYS clean the sprayer immediately after use according to the directions provided in this manual.

•Decontaminate. ALWAYS decontaminate yourself immediately after you are finished spraying and handling chemicals. Wash all exposed areas of the body with soap and water and remove and launder clothing.

•Chemical disposal/storage. ALWAYS dispose of or store remaining chemicals properly as recommended on the chemical label.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents M282737F Hazard Signal Word Definitions Table of Contents Spraying Pesticides Intended UseChemical Application Safety Summary of Important Safety InformationDuring Assembly General Chemical SafetyInhalation Chemical accident proceduresDifferently with filled sprayer attached Unpacking Closely inspect all contents in the shipping cartonFollowing items are found in the manual bag Unpacking the Manual BagStep Three Attach the cart base to the sprayer AssemblyStep One Attach the tongue to the cart base Step Two Attach the hitch mount to the tongueStep Five Attach pressure gauge Step Four Attach wheels to cart baseStep Six Attach gun hose to spray gun and pump Step Eight Attach drain cap to tank Step Seven Attach gun clips to tankStep Nine Attach hose guide to tank Preparatory safety Preparatory safety steps Step Eleven Connect power cords to vehicle batteryStep Ten Attach sprayer to vehicle To install battery clamps Separate powerPrepare wire ends Vehicle batteryPower cord may remain connected to the battery Attach remote switchTest the system for leaks with water Step Twelve Check and test completed assemblyCheck and test completed assembly Test with waterMachine Components General Chemical Safety Operation Important Safety InformationAfter Spraying Chemical Application SafetyBefore Spraying During SprayingTowing Safety Inhalation Operation Preparing the Sprayer for Each Use Important safety rulesInspect Inspect and test the sprayer thoroughly Repair Step One Assess wind conditions and clear work area Operation Using the SprayerSpray because the wind is too strong Ensure tank is flushed of all chemicals from prior uses Step Two Fill the sprayerFill tank Check drainThrough priming Hose Review safetyStep Three Operate the sprayer Ensure flowOperate spray gun as needed for application Proper Operation of the Spray GunImmediately Open until desired amount of agitation is achievedLaunder Step Four Clean sprayer and decontaminate after useDrain tank DecontaminateStorage Before attempting to service the sprayer TroubleshootingAny Questions, Comments, Problems or Parts Orders SpecificationsExploded View 282737 Rev. F Any Questions, Comments, Problems or Parts Orders

M282737F specifications

Panasonic has long been a key player in the electronics industry, providing innovative products that meet diverse consumer needs. One of their notable offerings is the Panasonic M282737F, a versatile and efficient device that showcases the company's commitment to quality and advanced technology.

The M282737F is designed primarily for industrial applications, catering to sectors that require reliable and high-performance solutions. Its standout feature is its robust construction, which ensures durability in demanding environments. This makes it an ideal choice for factories, warehouses, and other industrial settings where equipment faces wear and tear.

At the heart of the M282737F is Panasonic's cutting-edge technology, which includes enhanced energy efficiency capabilities. This device is engineered to minimize power consumption while maintaining optimal performance, thus reducing operational costs for businesses. These efficiency measures align with global efforts toward sustainability, making the M282737F a responsible choice for environmentally conscious companies.

In terms of usability, the M282737F offers intuitive controls and a user-friendly interface, allowing operators to seamlessly integrate it into their existing workflows. Its compatibility with various systems and platforms further enhances its versatility, ensuring that it can function effectively within diverse operational contexts. This interoperability means that users can leverage nostalgic legacy systems while also preparing for future advancements.

Additionally, safety features are paramount in the design of the M282737F. It is equipped with multiple safeguards that protect against overload and short circuits, ensuring a high level of reliability in critical applications. These built-in safety mechanisms also provide peace of mind to operators who depend on the device for their daily operations.

Another noteworthy characteristic of the M282737F is its compact and lightweight design. This factor not only makes it easier to install but also allows for flexibility in deployment, particularly in spaces where every square inch is valuable.

In summary, the Panasonic M282737F stands out as a prime example of the company's dedication to engineering excellence, energy efficiency, and user-friendly design. With its robust features, advanced technologies, and safety mechanisms, it is a worthy investment for any industrial operation looking to enhance productivity and reliability in their equipment.
Top Page Image Contents