Panasonic M282737F owner manual Troubleshooting, Before attempting to service the sprayer

Page 31

Troubleshooting

WARNING

Before troubleshooting or attempting to service, read the following safety rules to avoid accidental exposure to chemical and also risk of electric shock.

Note: A reserve, clean container capable of holding at least 16 gallons should be kept for use when the sprayer tank needs to be emptied temporarily for repairs. It is advisable to purchase a reserve tank suitable for pesticide storage from Northern Tool and Equipment for use in these circumstances. The container should be properly labeled as to its contents if it is used.

Before attempting to service the sprayer:

1.

Personal

Wear personal protective equipment as directed on the chemical label while

 

protective

servicing your sprayer.

 

equipment

 

2.

Review

Review the Troubleshooting Table below for the type of problem you are

 

troubleshooting

experiencing. However, DO NOT attempt to repair until the steps listed below

 

table

are followed.

 

 

 

3.

Empty and flush

If the cause listed for your problem is Clogged intake tube, Clogged suction

 

 

strainer, or Worn spray gun nozzle: empty the tank and flush the sprayer with

 

 

water as directed in the section, “Operation – Step Four”.

 

 

- In order to avoid accidental exposure to chemicals, never attempt to

 

 

unclog the intake tube or suction strainer, or service the spray gun nozzle,

 

 

until the tank has been emptied and the sprayer flushed with water.

 

 

 

4.

Disconnect

Disconnect power to the sprayer and be sure all system pressure is relieved

 

power/relieve

by squeezing the gun trigger.

 

pressure

 

5.

Perform repairs

Follow the directions provided in the troubleshooting table to repair the

 

 

sprayer.

 

 

NOTE: Never try to unclog the sprayer nozzle by blowing through it.

 

 

 

6.

Test after

After servicing, ALWAYS test the sprayer for leaks with plain water before

 

servicing

using.

 

 

 

PROBLEM

CAUSE

SOLUTION

 

Bad electrical connection

Check battery connections.

 

Short in wires

Check condition of wires.

Pump will not turn on

Motor hooked to battery

Ensure red wire is connected to positive

battery terminal. If not, correct wiring,

 

 

incorrectly

then remove pump head and tighten

 

 

offset bearing.

Low pressure

Worn spray gun nozzle

Replace spray gun.

Improper pressure adjustment

Tighten pressure adjustment knob.

 

 

Clogged intake tube

Remove obstruction.

Low flow

Clogged suction strainer

Clean suction strainer.

Obstruction in inlet/outlet valves

Clean inlet/outlet valves.

 

 

Leak in the system

Tighten leaking hose clamps or fittings.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents M282737F Hazard Signal Word Definitions Table of Contents Spraying Pesticides Intended UseChemical Application Safety Summary of Important Safety InformationDuring Assembly General Chemical SafetyInhalation Chemical accident proceduresDifferently with filled sprayer attached Unpacking Closely inspect all contents in the shipping cartonFollowing items are found in the manual bag Unpacking the Manual BagStep Three Attach the cart base to the sprayer AssemblyStep One Attach the tongue to the cart base Step Two Attach the hitch mount to the tongueStep Five Attach pressure gauge Step Four Attach wheels to cart baseStep Six Attach gun hose to spray gun and pump Step Eight Attach drain cap to tank Step Seven Attach gun clips to tankStep Nine Attach hose guide to tank Preparatory safety Preparatory safety steps Step Eleven Connect power cords to vehicle batteryStep Ten Attach sprayer to vehicle To install battery clamps Separate powerPrepare wire ends Vehicle batteryPower cord may remain connected to the battery Attach remote switchTest the system for leaks with water Step Twelve Check and test completed assemblyCheck and test completed assembly Test with waterMachine Components General Chemical Safety Operation Important Safety InformationAfter Spraying Chemical Application SafetyBefore Spraying During SprayingTowing Safety Inhalation Operation Preparing the Sprayer for Each Use Important safety rulesInspect Inspect and test the sprayer thoroughly Repair Step One Assess wind conditions and clear work area Operation Using the SprayerSpray because the wind is too strong Ensure tank is flushed of all chemicals from prior uses Step Two Fill the sprayerFill tank Check drainThrough priming Hose Review safetyStep Three Operate the sprayer Ensure flowOperate spray gun as needed for application Proper Operation of the Spray GunImmediately Open until desired amount of agitation is achievedLaunder Step Four Clean sprayer and decontaminate after useDrain tank DecontaminateStorage Before attempting to service the sprayer TroubleshootingAny Questions, Comments, Problems or Parts Orders SpecificationsExploded View 282737 Rev. F Any Questions, Comments, Problems or Parts Orders

M282737F specifications

Panasonic has long been a key player in the electronics industry, providing innovative products that meet diverse consumer needs. One of their notable offerings is the Panasonic M282737F, a versatile and efficient device that showcases the company's commitment to quality and advanced technology.

The M282737F is designed primarily for industrial applications, catering to sectors that require reliable and high-performance solutions. Its standout feature is its robust construction, which ensures durability in demanding environments. This makes it an ideal choice for factories, warehouses, and other industrial settings where equipment faces wear and tear.

At the heart of the M282737F is Panasonic's cutting-edge technology, which includes enhanced energy efficiency capabilities. This device is engineered to minimize power consumption while maintaining optimal performance, thus reducing operational costs for businesses. These efficiency measures align with global efforts toward sustainability, making the M282737F a responsible choice for environmentally conscious companies.

In terms of usability, the M282737F offers intuitive controls and a user-friendly interface, allowing operators to seamlessly integrate it into their existing workflows. Its compatibility with various systems and platforms further enhances its versatility, ensuring that it can function effectively within diverse operational contexts. This interoperability means that users can leverage nostalgic legacy systems while also preparing for future advancements.

Additionally, safety features are paramount in the design of the M282737F. It is equipped with multiple safeguards that protect against overload and short circuits, ensuring a high level of reliability in critical applications. These built-in safety mechanisms also provide peace of mind to operators who depend on the device for their daily operations.

Another noteworthy characteristic of the M282737F is its compact and lightweight design. This factor not only makes it easier to install but also allows for flexibility in deployment, particularly in spaces where every square inch is valuable.

In summary, the Panasonic M282737F stands out as a prime example of the company's dedication to engineering excellence, energy efficiency, and user-friendly design. With its robust features, advanced technologies, and safety mechanisms, it is a worthy investment for any industrial operation looking to enhance productivity and reliability in their equipment.
Top Page Image Contents