Safety Guidelines, Safety with Equipment | Cisco Systems A9014CFD

C H A P T E R 2

Preparing to Install the Router

This chapter describes site requirements and equipment used to install the Cisco ASR 901 router. It includes the following sections:

•Safety Guidelines, page 2-1

•Prerequisites, page 2-4

•Site Planning, page 2-4

•Console Port Considerations, page 2-8

Safety Guidelines

Before you begin installing the Cisco ASR 901 router, review the safety guidelines in Safety Precautions, page 1-5, and the Rack-Mounting Configuration Guidelines, page 3-2to avoid injuries or damaging the equipment.

In addition, before replacing, configuring, or maintaining the Cisco ASR 901 router, review the safety warnings listed in the document Cisco Regulatory Compliance and Safety Information for Cisco ASR 901 Series Aggregation Services Router.

Safety with Equipment

The following guidelines help ensure your safety and protect the equipment. This list does not include all the potentially hazardous situations, so be alert.

Warning Before connecting the system to the power source, read the installation instructions. Statement 1004

•Before moving the system, always disconnect all the power cords and interface cables.

•Never assume that power is disconnected from a circuit; always check.

•Before and after installation, keep the chassis area clean and dust-free.

•Keep tools and assembly components away from walk areas to avoid tripping over them.

•Do not work alone in potentially hazardous conditions.

•Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

•Do not wear loose clothing that may get caught in the chassis.

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

	OL-23778-01	2-1

Image 19

Cisco Systems A9014CFD, ASR 9014CFD manual Safety Guidelines, Safety with Equipment

Contents

Text Part Number OL-23778-01 Americas HeadquartersPage N T E N T S Required Tools and Equipment Troubleshooting A-1 OL-23778-01 Revision Date Change Summary Document Revision History Conventions ObjectivesAudience Organization Related Documentation Safety Warnings About This Guide Hardware Description Introduction Cisco ASR 901 Router Front View Cisco ASR 901 Router-Front View Cisco ASR 901 Router Ethernet Version Front View Fan Grounding Point Lug Cisco ASR 901 Router Rear View LEDs Power SupplySafety Precautions Specification Value Pin Connector B Pin Connector a Router Interface Numbering Environmental Monitoring Temperature SensorSystem Specifications Description Specification Interface Number Location Label Regulatory Compliance Safety with Equipment Safety Guidelines Safety with Electricity Preventing Electrostatic Discharge Damage Site Environment Power Supply ConsiderationsPrerequisites Site Planning Air Flow Guidelines Method of Procedure Required Tools and Equipment Unpacking and Checking the Contents of your Shipment Task Verified by Date Installation Checklist Task Verified by Console Port ConsiderationsCreating a Site Log Console Port Connections Preparing to Install the Router Console Port Considerations OL-23778-01 Network Modules Installing the Cisco ASR 901 Mobile Wireless Router Mounting the Cisco ASR 901 Router Rack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 Router in a Rack Attaching the Rack-Mounting Brackets Attaching the Cable Guides Grounding the Cisco ASR 901 Router Connecting the Chassis Ground and Power Grounding Point Stripping a Ground Wire Power Connection Compliance 6-Pin Terminal Block Wiring the DC-Input Power Source Installing SFP Modules Installing and Removing SFP Modules Removing SFP Modules Installing an SFP Module into an SFP Module Slot Connecting the Console Port Connecting Cables Console Port Types of RJ-45 Cables Connecting Gigabit Ethernet Interface Cables Connecting the Network CablesConnecting T1 and E1 Interface Cables Connecting Cables to the Bits Interface Connecting SFP CablesConnecting GPS Cables Dressing Router Cables Powering On the RouterConnecting to Alarm Port Connecting to the Management Ethernet Port Interpreting Front-Panel LEDs Checklist for Power UpPower-On Procedure Formatting Procedures for Flash Memory Displaying Contents of the Flash Memory File and Directory ProceduresCopying Files Deleting Files from the Flash Memory Displaying File Content Enter a Directory and Determine the Current Directory What to Do After Installing the Hardware OL-23778-01 Problem Solving Troubleshooting Environmental Reporting Features Troubleshooting the Power and Cooling SystemsSymptom Possible Cause Corrective Action Information Packet publication Troubleshooting Cables, and Connections System LED Reading the LEDsChassis LEDs Copper GE from Quad combo PHY ports contain Two Leds each Color/State Description two LEDs for each T1/E1 port T1/E1 Interface LEDsSFP Ethernet Interface LEDs RJ-45 Ethernet Interface LEDs OL-23778-01 Gigabit Ethernet Connector Pinouts Cable Specifications Pin FE Signal GE Signal SFP Port Pinouts and Cable SpecificationsT1/E1 Port Pinouts Console Port Signals and Pinouts Console Port Signals and PinoutsPin Signal Name Direction Description RJ-45-to-DB-9 Terminal Adapter Console Pin Signal Name HP Pins Direction Description Identifying a Rollover Cable Terminal Adapter Device Signal RJ-45 Pin DB-25 PinConsole RJ-45-to-DB-25 Port DTE Time of Day Pinouts Bits Port PinoutsGPS Port Pinouts 10 Mhz Alarm Port PinoutsPin Signal Name Description Management Ethernet Port Pinouts RxDP RxDN TxDP Not connected TxDN Site Log Initials Date Numerics IN-2 IN-3 IN-4