Wiring the DC-Input Power Source | Cisco Systems ASR 9014CFD

Chapter 3 Installing the Cisco ASR 901 Mobile Wireless Router

Mounting the Cisco ASR 901 Router

Wiring the DC-Input Power Source

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than 10 A minimum, 60 VDC. Statement 1005

Complete the following steps to connect the DC power supply to the Cisco ASR 901 router:

Step 1 Switch off the DC power source at the circuit breaker, and place the circuit breaker in the Off position.

Step 2 Locate the 6-pin terminal block (part number 27-2030-01) (Figure 3-6). The terminal block is located in the accessory kit (part number 53-3085-01 for the Cisco ASR 901 router), which is shipped with the router.

Figure 3-6 6-Pin Terminal Block

282346

Step 3 Plug the 6-pin terminal block into the power connector located on the front side of the router.

Step 4 Connect one end of the customer-supplied power cord (16-AWG copper wire) to the site DC power source.

Step 5 Plug the connector on the power supply cord into the 6-pin terminal block that you plugged into the rear of the router in Step 3.

Warning An exposed wire lead from a DC-input power source can conduct harmful levels of electricity. Be sure that no exposed portion of the DC-input power source wire extends from the terminal block plug. Statement 122

Warning When installing this unit, secure all power cabling to avoid disturbing field-wiring connections. Statement 38

Caution DO NOT power on the unit yet.

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

3-8	OL-23778-01

Image 36

Cisco Systems ASR 9014CFD, A9014CFD manual Wiring the DC-Input Power Source, Pin Terminal Block

Contents

Americas Headquarters Text Part Number OL-23778-01Page N T E N T S Required Tools and Equipment Troubleshooting A-1 OL-23778-01 Document Revision History Revision Date Change Summary Objectives AudienceOrganization Conventions Safety Warnings Related Documentation About This Guide Introduction Hardware Description Cisco ASR 901 Router Front View Cisco ASR 901 Router Ethernet Version Front View Cisco ASR 901 Router-Front View Cisco ASR 901 Router Rear View Fan Grounding Point Lug Power Supply Safety PrecautionsSpecification Value LEDs Pin Connector a Pin Connector B Environmental Monitoring Temperature Sensor System SpecificationsDescription Specification Router Interface Numbering Regulatory Compliance Interface Number Location Label Safety Guidelines Safety with Equipment Safety with Electricity Preventing Electrostatic Discharge Damage Power Supply Considerations PrerequisitesSite Planning Site Environment Method of Procedure Air Flow Guidelines Unpacking and Checking the Contents of your Shipment Required Tools and Equipment Installation Checklist Task Verified by Date Console Port Considerations Creating a Site LogConsole Port Connections Task Verified by Preparing to Install the Router Console Port Considerations OL-23778-01 Installing the Cisco ASR 901 Mobile Wireless Router Network Modules Rack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 Router Attaching the Rack-Mounting Brackets Mounting the Cisco ASR 901 Router in a Rack Attaching the Cable Guides Connecting the Chassis Ground and Power Grounding the Cisco ASR 901 Router Grounding Point Power Connection Compliance Stripping a Ground Wire Wiring the DC-Input Power Source 6-Pin Terminal Block Installing and Removing SFP Modules Installing SFP Modules Installing an SFP Module into an SFP Module Slot Removing SFP Modules Connecting Cables Connecting the Console Port Types of RJ-45 Cables Console Port Connecting the Network Cables Connecting Gigabit Ethernet Interface CablesConnecting T1 and E1 Interface Cables Connecting SFP Cables Connecting Cables to the Bits InterfaceConnecting GPS Cables Powering On the Router Connecting to Alarm PortConnecting to the Management Ethernet Port Dressing Router Cables Checklist for Power Up Power-On ProcedureFormatting Procedures for Flash Memory Interpreting Front-Panel LEDs File and Directory Procedures Displaying Contents of the Flash MemoryCopying Files Displaying File Content Deleting Files from the Flash Memory What to Do After Installing the Hardware Enter a Directory and Determine the Current Directory OL-23778-01 Troubleshooting Problem Solving Troubleshooting the Power and Cooling Systems Environmental Reporting FeaturesSymptom Possible Cause Corrective Action Troubleshooting Cables, and Connections Information Packet publication Reading the LEDs Chassis LEDsCopper GE from Quad combo PHY ports contain Two Leds each System LED T1/E1 Interface LEDs SFP Ethernet Interface LEDsRJ-45 Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 port OL-23778-01 Cable Specifications Gigabit Ethernet Connector Pinouts SFP Port Pinouts and Cable Specifications Pin FE Signal GE SignalT1/E1 Port Pinouts Console Port Signals and Pinouts Console Port Signals and PinoutsPin Signal Name Direction Description Pin Signal Name HP Pins Direction Description RJ-45-to-DB-9 Terminal Adapter Console Terminal Adapter Device Signal RJ-45 Pin DB-25 Pin Identifying a Rollover CableConsole RJ-45-to-DB-25 Port DTE Bits Port Pinouts Time of Day PinoutsGPS Port Pinouts Alarm Port Pinouts Pin Signal Name DescriptionManagement Ethernet Port Pinouts 10 Mhz RxDP RxDN TxDP Not connected TxDN Site Log Date Initials Numerics IN-2 IN-3 IN-4