SFP Port Pinouts and Cable Specifications | Cisco Systems 901

Appendix B Cable Specifications

SFP Port Pinouts and Cable Specifications

Table B-1		RJ-45 Connector Pinouts

Pin	FE Signal		GE Signal

3	RX data+		RX B+

4	Not used		TX C+

5	Not used		TX C–

6	RX data–		RX B–

7	Not used		RX D+

8	Not used		RX D–

SFP Port Pinouts and Cable Specifications

For information about SFP modules supported by the Cisco ASR 901 router, including pinouts, see the Cisco Interfaces and Modules support section on Cisco.com.

Note Pins not listed in the tables in this appendix are not connected

T1/E1 Port Pinouts

Figure B-2shows the RJ-48C connector used by the T1/E1 ports on the TDM interface module on the Cisco ASR 901 router.

Figure B-2 RJ-48C Connector

87654321

RJ-48C connector

24939

Figure B-3shows the RJ-48C connector wiring for the T1/E1 cable.

Figure B-3 RJ-48-to-RJ-48 T1/E1 Cable Wiring

1

8

			H11419
			Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide


	B-2		OL-23778-01
	B-2		OL-23778-01

Image 56

Cisco Systems ASR 9014CFD manual SFP Port Pinouts and Cable Specifications, T1/E1 Port Pinouts, Pin FE Signal GE Signal

Contents

Americas Headquarters Text Part Number OL-23778-01Page N T E N T S Required Tools and Equipment Troubleshooting A-1 OL-23778-01 Document Revision History Revision Date Change Summary Objectives AudienceOrganization Conventions Safety Warnings Related Documentation About This Guide Introduction Hardware Description Cisco ASR 901 Router Front View Cisco ASR 901 Router Ethernet Version Front View Cisco ASR 901 Router-Front View Cisco ASR 901 Router Rear View Fan Grounding Point Lug Power Supply Safety PrecautionsSpecification Value LEDs Pin Connector a Pin Connector B Environmental Monitoring Temperature Sensor System SpecificationsDescription Specification Router Interface Numbering Regulatory Compliance Interface Number Location Label Safety Guidelines Safety with Equipment Safety with Electricity Preventing Electrostatic Discharge Damage Power Supply Considerations PrerequisitesSite Planning Site Environment Method of Procedure Air Flow Guidelines Unpacking and Checking the Contents of your Shipment Required Tools and Equipment Installation Checklist Task Verified by Date Console Port Considerations Creating a Site LogConsole Port Connections Task Verified by Preparing to Install the Router Console Port Considerations OL-23778-01 Installing the Cisco ASR 901 Mobile Wireless Router Network Modules Rack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 Router Attaching the Rack-Mounting Brackets Mounting the Cisco ASR 901 Router in a Rack Attaching the Cable Guides Connecting the Chassis Ground and Power Grounding the Cisco ASR 901 Router Grounding Point Power Connection Compliance Stripping a Ground Wire Wiring the DC-Input Power Source 6-Pin Terminal Block Installing and Removing SFP Modules Installing SFP Modules Installing an SFP Module into an SFP Module Slot Removing SFP Modules Connecting Cables Connecting the Console Port Types of RJ-45 Cables Console Port Connecting T1 and E1 Interface Cables Connecting the Network CablesConnecting Gigabit Ethernet Interface Cables Connecting GPS Cables Connecting SFP CablesConnecting Cables to the Bits Interface Powering On the Router Connecting to Alarm PortConnecting to the Management Ethernet Port Dressing Router Cables Checklist for Power Up Power-On ProcedureFormatting Procedures for Flash Memory Interpreting Front-Panel LEDs Copying Files File and Directory ProceduresDisplaying Contents of the Flash Memory Displaying File Content Deleting Files from the Flash Memory What to Do After Installing the Hardware Enter a Directory and Determine the Current Directory OL-23778-01 Troubleshooting Problem Solving Symptom Possible Cause Corrective Action Troubleshooting the Power and Cooling SystemsEnvironmental Reporting Features Troubleshooting Cables, and Connections Information Packet publication Reading the LEDs Chassis LEDsCopper GE from Quad combo PHY ports contain Two Leds each System LED T1/E1 Interface LEDs SFP Ethernet Interface LEDsRJ-45 Ethernet Interface LEDs Color/State Description two LEDs for each T1/E1 port OL-23778-01 Cable Specifications Gigabit Ethernet Connector Pinouts T1/E1 Port Pinouts SFP Port Pinouts and Cable SpecificationsPin FE Signal GE Signal Pin Signal Name Direction Description Console Port Signals and PinoutsConsole Port Signals and Pinouts Pin Signal Name HP Pins Direction Description RJ-45-to-DB-9 Terminal Adapter Console Console RJ-45-to-DB-25 Port DTE Terminal Adapter Device Signal RJ-45 Pin DB-25 PinIdentifying a Rollover Cable GPS Port Pinouts Bits Port PinoutsTime of Day Pinouts Alarm Port Pinouts Pin Signal Name DescriptionManagement Ethernet Port Pinouts 10 Mhz RxDP RxDN TxDP Not connected TxDN Site Log Date Initials Numerics IN-2 IN-3 IN-4