Power Connection Compliance | Cisco Systems ASR 9014CFD manual

Chapter 3 Installing the Cisco ASR 901 Mobile Wireless Router

Mounting the Cisco ASR 901 Router

Figure 3-4 Stripping a Ground Wire

0.5 in. (12.7 mm) ± 0.02 in. (0.5 mm)

Insulation

Wire lead

60528

Step 4 Slide the open end of your ground lug over the exposed area of the ground wire.

Step 5 Using a crimping tool (as specified by the ground lug manufacturer), crimp the ground lug to the ground wire (Figure 3-5).

Figure 3-5 Crimping a Ground Lug onto the Ground Wire

60529

Step 6 Use a Phillips head screwdriver to attach the ground lug and wire assembly to the front of the router with the 2 screws from the accessory kit.

Step 7 Connect the other end of the ground wire to a suitable grounding point at your site.

Power Connection Compliance

Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. Statement 1003

Warning Use copper conductors only. Statement 1025

Note The installation must comply with the 2002 National Electric Code (NEC) and other applicable codes.

Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide

	OL-23778-01	3-7

Image 35

Cisco Systems ASR 9014CFD, A9014CFD manual Power Connection Compliance, Stripping a Ground Wire

Contents

Text Part Number OL-23778-01 Americas HeadquartersPage N T E N T S Required Tools and Equipment Troubleshooting A-1 OL-23778-01 Revision Date Change Summary Document Revision History Conventions ObjectivesAudience Organization Related Documentation Safety Warnings About This Guide Hardware Description Introduction Cisco ASR 901 Router Front View Cisco ASR 901 Router-Front View Cisco ASR 901 Router Ethernet Version Front View Fan Grounding Point Lug Cisco ASR 901 Router Rear View LEDs Power SupplySafety Precautions Specification Value Pin Connector B Pin Connector a Router Interface Numbering Environmental Monitoring Temperature SensorSystem Specifications Description Specification Interface Number Location Label Regulatory Compliance Safety with Equipment Safety Guidelines Safety with Electricity Preventing Electrostatic Discharge Damage Site Environment Power Supply ConsiderationsPrerequisites Site Planning Air Flow Guidelines Method of Procedure Required Tools and Equipment Unpacking and Checking the Contents of your Shipment Task Verified by Date Installation Checklist Task Verified by Console Port ConsiderationsCreating a Site Log Console Port Connections Preparing to Install the Router Console Port Considerations OL-23778-01 Network Modules Installing the Cisco ASR 901 Mobile Wireless Router Mounting the Cisco ASR 901 Router Rack-Mounting Configuration Guidelines Mounting the Cisco ASR 901 Router in a Rack Attaching the Rack-Mounting Brackets Attaching the Cable Guides Grounding the Cisco ASR 901 Router Connecting the Chassis Ground and Power Grounding Point Stripping a Ground Wire Power Connection Compliance 6-Pin Terminal Block Wiring the DC-Input Power Source Installing SFP Modules Installing and Removing SFP Modules Removing SFP Modules Installing an SFP Module into an SFP Module Slot Connecting the Console Port Connecting Cables Console Port Types of RJ-45 Cables Connecting T1 and E1 Interface Cables Connecting the Network CablesConnecting Gigabit Ethernet Interface Cables Connecting GPS Cables Connecting SFP CablesConnecting Cables to the Bits Interface Dressing Router Cables Powering On the RouterConnecting to Alarm Port Connecting to the Management Ethernet Port Interpreting Front-Panel LEDs Checklist for Power UpPower-On Procedure Formatting Procedures for Flash Memory Copying Files File and Directory ProceduresDisplaying Contents of the Flash Memory Deleting Files from the Flash Memory Displaying File Content Enter a Directory and Determine the Current Directory What to Do After Installing the Hardware OL-23778-01 Problem Solving Troubleshooting Symptom Possible Cause Corrective Action Troubleshooting the Power and Cooling SystemsEnvironmental Reporting Features Information Packet publication Troubleshooting Cables, and Connections System LED Reading the LEDsChassis LEDs Copper GE from Quad combo PHY ports contain Two Leds each Color/State Description two LEDs for each T1/E1 port T1/E1 Interface LEDsSFP Ethernet Interface LEDs RJ-45 Ethernet Interface LEDs OL-23778-01 Gigabit Ethernet Connector Pinouts Cable Specifications T1/E1 Port Pinouts SFP Port Pinouts and Cable SpecificationsPin FE Signal GE Signal Pin Signal Name Direction Description Console Port Signals and PinoutsConsole Port Signals and Pinouts RJ-45-to-DB-9 Terminal Adapter Console Pin Signal Name HP Pins Direction Description Console RJ-45-to-DB-25 Port DTE Terminal Adapter Device Signal RJ-45 Pin DB-25 PinIdentifying a Rollover Cable GPS Port Pinouts Bits Port PinoutsTime of Day Pinouts 10 Mhz Alarm Port PinoutsPin Signal Name Description Management Ethernet Port Pinouts RxDP RxDN TxDP Not connected TxDN Site Log Initials Date Numerics IN-2 IN-3 IN-4