Specifications | Mitsubishi Electronics XD95U specification

Specifications

Projector specifications

All specifications are subject to change without notice.

General

Product name	DLPTM DATA Projector
Model name	XD95U

Optical

Resolution	1024 x 768 XGA

Display system	1-CHIP DMD

Lens F/Number	F = 2.56 to 2.67, f = 21.36 to 23.45 mm

Lamp	200 W lamp

Electrical

Power supply	AC100–240V, 2.9 A, 50/60 Hz (Automatic)

Power consumption	285 W (Max)

Mechanical

Dimensions	190 mm (W) x 84.2 mm (H) x 205.2 mm (D)

Weight	3.3 lbs (1.5 Kg)

Input terminal

Computer input

RGB input	D-Sub 15-pin (female) x 1

Video signal input

S-VIDEO	Mini DIN 4-pin port x 1

VIDEO	RCA jack x 1

SD/HDTV signal input	Analog – D-Sub <–> Component RCA jack x 3
	(through RGB input)
Control terminal

RS-232 serial control	8 pin x 1

Environmental requirements

Operating temperature	0°C–35°C at sea level

Operating relative humidity	10%–90% (without condensation)

Operating altitude	• 0–1499 m at 0°C–35°C
	• 1500–3000 m at 0°C–30°C (with High Altitude Mode on)

EN-42

Image 42

Mitsubishi Electronics XD95U user manual Specifications, Projector specifications

Contents

XD95U Shock EN-3 Contents Important safeguards Compliance Notice of Industry Canada Front/upper side Projector exterior viewKensington Lock External control panel Controls and functions Projector Remote control Freeze Remote control effective range Pull out the battery holder Positioning your projector Choosing a locationObtaining a preferred projected image size EN-12 Standard Layout of the projectorFront projection 169 Connecting a computer Connecting Video source devicesConnection To connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source device Connecting a composite Video source device To connect the projector to a composite Video source device Operation Starting up the projector Using the menus Use / to highlight the System Setup Basic menu If you forget the password Utilizing the password functionSetting a password Entering the password recall procedure Disabling the password function Switching input signalChanging the password Enter the old password Auto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarity Magnifying and searching for details Correcting keystone Selecting the aspect ratio Altering the images aspect ratio Setting the User 1/User 2 mode Selecting a picture modePicture modes for different types of signals Optimizing the image Fine-tuning the image quality in user modes Using Wall Color 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays Setting the presentation timer To cancel the timer, perform the following stepsHow to use the Timer On key? Locking control keys Setup Basic Panel Key Lock menu, and select On by pressingHiding the image Freezing the image Personalizing the projector menu display To activate the High Altitude ModeOperating in a high altitude environment Shutting down the projector Main menu Sub-menu Options Menu operationMenu system Basic Advanced Description of each menu Blank Timer Presentation TimerAuto Power Off Timer Controller Security Settings Setup menu Reset All SettingsCurrent System Status Maintenance Care of the projector Lamp information Setting Lamp mode as LowSetting Auto Power Off Getting to know the lamp hour Timing of replacing the lamp Projector until the 2950 hour lamp warning appearsLamp has been in operation for 3000 hours Replacing the lamp Spare lamp for XD95U VLT-XD95LP Resetting the lamp timer Tighten the screw that secures the lampRestart the projector Projector needs 90 seconds to cool down IndicatorsDown without the normal cooling down process Please contact your dealer for assistance Troubleshooting Specifications Projector specifications Dimensions Timing chart Supported timing for Component-YPbPrinput Mitsubishi Electric Corporation