Porter-Cable PCH3600GRC, D25806-025-2 Starting, To Shut Down, Release trigger to stop water flow

Page 12

TO SHUT DOWN

IMPORTANT: Read and understand how to shut down the pressure washer before operating.

1.If you have siphoned chemicals, siphon a bucket of clean water through the chemical hose. NOTE: Failure to do so will cause damage to the pump.

2.Refer to engine manual for correct engine shut down procedure.

NOTE: NEVER turn the water off with the engine running.

3.Turn water source off.

4.Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

5.See Storage section in this manual for proper storage procedures.

STARTING

Prior to starting, refer to your engine manual for proper starting procedures for your engine type.

1.In a well ventilated outdoor area Add fresh high quality unleaded gasoline with a pump octane rating of 86 or higher. Do not overfill. Wipe up spilled fuel before starting the engine. Refer to engine manual for correct procedure.

2.Check engine oil level. See Engine Operators Manual for correct procedure.

NOTE: There will be a slight amount of oil in the engine from factory testing.

3.Verify the filter screen is in water inlet of pump. NOTE:

Cone side faces out.

Filter Screen

4.Connect water source to pump inlet.

NOTE: Water source must provide a minimum of 5 gal- lons per minute at 20 p.s.i.

5.Connect high pressure hose to pump outlet.

6.If applying a chemical or cleaning solution, see How To Siphon Chemicals/Cleaning Solvents in Operation section of this manual.

7.

Turn water source on. NOTE: Make sure water

 

High Pressure Hose

 

 

 

 

 

 

 

 

supply is turned on.

 

 

 

 

 

8.

Start engine. See Engine operators Manual for cor-

 

 

 

 

 

 

rect procedure. NOTE: If the engine does not start

 

 

 

 

 

 

after two pulls, pull the trigger to relieve the pres-

 

 

 

 

 

 

sure.

 

 

 

 

 

9.

Depress trigger on gun to start water flow. NOTE:

 

 

 

 

 

 

Stand on a stable surface and grip gun/wand firmly

 

 

Water

 

 

with both hands. Expect the gun to kick when trig-

 

 

Source

 

 

 

 

 

 

 

 

gered.

 

 

 

 

 

10.Release trigger to stop water flow.

11.Adjust nozzle spray for the task being performed or change quick connect tip. See How To Use Wand instructions in this section.

D25806

12- ENG

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Manual PCH3600GRCGeneral Information Safety Guidelines / Definitions Important Safety InstructionsHazard What can Happen Never leave wand unattended while unit is running BOX Contents Assembly Operation Pressure WasherHOW to USE To Adjust PressureBasic Elements of Engine Pressure Washer TerminologyTo USE Wand To Siphon CHEMICALS/CLEANING Solvents Read and Understand ALL Warnings Before Starting UnitPress chemical hose onto barbed fitting located Starting To Shut DownRelease trigger to stop water flow Maintenance How To Change Pump OilEngine PumpHOW to Clean the Water Inlet Filter WandReconnect spark plug wire StorageEngine Pump Windshield washer fluid may also be usedTroubleshooting Guide Problem CausecorrectionProblem CauseCorrection Limited Warranty ENG D25806 Quick Facts Call

PCH3600GRC, D25806-025-2 specifications

The Porter-Cable D25806-025-2 and PCH3600GRC are two noteworthy tools designed to enhance productivity and efficiency in various construction and DIY projects. These devices embody the ethos of reliability and performance that Porter-Cable is known for, catering to both professional contractors and serious hobbyists.

The Porter-Cable D25806-025-2 is a powerful 5 amp rotary hammer that excels in drilling through concrete, masonry, and other tough materials. Its robust design features a 1-inch hammering mechanism, delivering a significant impact energy that ensures effective drilling in challenging conditions. The tool is equipped with a variable speed control, allowing users to adjust the speed to match the task at hand. This feature proves particularly useful when transitioning between different materials or when precision is paramount. Additionally, the D25806-025-2 incorporates a durable SDS Plus chuck, enabling quick and easy bit changes with minimal downtime.

One of the standout technologies incorporated into the D25806-025-2 is its anti-vibration system. By minimizing vibrations during operation, this feature significantly enhances user comfort, especially during prolonged use. Moreover, the tool’s two-mode operation allows for efficient switching between rotary hammer and chiseling functions, making it versatile for a variety of applications, from drilling holes to chipping away at existing structures.

On the other hand, the PCH3600GRC is an innovative cordless pancake air compressor that delivers reliable power without the constraints of cords. With its 6-gallon capacity tank and 0.8 SCFM output at 90 PSI, this compressor is ideal for a broad range of air tools. Portability is a prime characteristic of the PCH3600GRC, as it is lightweight and features a handle, making it easy to transport to different job sites.

The compressor also integrates a quiet operation technology, reducing noise levels significantly which is especially beneficial in residential areas or enclosed spaces. Users can expect fewer disturbances while still enjoying a high level of performance. The dual outlet configuration enables multiple tools to be connected simultaneously, enhancing productivity.

In summary, both the Porter-Cable D25806-025-2 and PCH3600GRC represent top-tier engineering and technology innovation. The D25806-025-2 offers substantial power and versatility for heavy-duty tasks, while the PCH3600GRC stands out for its portability and quiet operation, making them essential tools for modern tradespeople and home improvement enthusiasts alike.
Top Page Image Contents