Porter-Cable PCH3600GRC, D25806-025-2 Troubleshooting Guide, Problem Causecorrection

Page 16

TROUBLESHOOTING GUIDE

PROBLEM

CAUSECORRECTION

Engine will not start (see Engine Manual for fur- ther engine troubleshooting)

No fuel.

Low oil (if equipped with low oil shutdown).

Pressure builds up after two pulls on the recoil starter or after initial use.

Not primed or choked.

Spark plug wire not attached.

Engine ON/OFF switch in OFF po- sition (If applicable.)

Choke lever in the “Choke” posi- tion on a “hot” engine or an engine that has been exposed to thermal heat for a long period of time.

Add Fuel.

Add required amount of oil.

Squeeze gun trigger to relieve pressure.

Push primer bulb 3 times or choke engine.

Attach spark plug wire.

Place engine ON/OFF switch in on position.

Move choke to the “No Choke” position.

No or low pressure (initial use)

Fuel valve closed (if equipped)

Wand not in high pressure.

Low water supply.

Leak at high pressure hose.

Nozzle obstructed.

Water filter screen clogged. Defective E-Z start valve.

Air in hose.

Choke lever in the “Choke” position.

Throttle control lever is not in the “Fast” position. (if equipped)

High pressure hose is too long.

Move the fuel valve lever to the “Open” position.

See How to Use Wand paragraph in the Operation Section.

Water supply must be at least 5 GPM @ 20 PSI.

Repair leak. Apply sealant tape if necessary.

Clean nozzle with paper clip or nozzle cleaning tool, pour water into nozzle end to flush out ob- struction.

Remove and clean filter.

Check with Authorized Warranty Service Center (AWSC.)

Turn off the engine, then the water source. Disconnect the water source from the pump inlet and turn the water source on to remove all air from the hose. When there is a steady stream of water present, turn water source off. Reconnect water source to pump inlet and turn on water source. Squeeze trigger to re- move remaining air

Move choke to the “No Choke” position.

Move throttle control lever to the “Fast” position.

Use high pressure hose under 100 feet.

D25806

16- ENG

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Manual PCH3600GRCGeneral Information Safety Guidelines / Definitions Important Safety InstructionsHazard What can Happen Never leave wand unattended while unit is running BOX Contents Assembly Operation Pressure WasherHOW to USE To Adjust PressureBasic Elements of Engine Pressure Washer TerminologyTo USE Wand Read and Understand ALL Warnings Before Starting Unit To Siphon CHEMICALS/CLEANING SolventsPress chemical hose onto barbed fitting located To Shut Down StartingRelease trigger to stop water flow Maintenance How To Change Pump OilEngine PumpHOW to Clean the Water Inlet Filter WandReconnect spark plug wire StorageEngine Pump Windshield washer fluid may also be usedTroubleshooting Guide Problem CausecorrectionCause ProblemCorrection Limited Warranty ENG D25806 Quick Facts Call

PCH3600GRC, D25806-025-2 specifications

The Porter-Cable D25806-025-2 and PCH3600GRC are two noteworthy tools designed to enhance productivity and efficiency in various construction and DIY projects. These devices embody the ethos of reliability and performance that Porter-Cable is known for, catering to both professional contractors and serious hobbyists.

The Porter-Cable D25806-025-2 is a powerful 5 amp rotary hammer that excels in drilling through concrete, masonry, and other tough materials. Its robust design features a 1-inch hammering mechanism, delivering a significant impact energy that ensures effective drilling in challenging conditions. The tool is equipped with a variable speed control, allowing users to adjust the speed to match the task at hand. This feature proves particularly useful when transitioning between different materials or when precision is paramount. Additionally, the D25806-025-2 incorporates a durable SDS Plus chuck, enabling quick and easy bit changes with minimal downtime.

One of the standout technologies incorporated into the D25806-025-2 is its anti-vibration system. By minimizing vibrations during operation, this feature significantly enhances user comfort, especially during prolonged use. Moreover, the tool’s two-mode operation allows for efficient switching between rotary hammer and chiseling functions, making it versatile for a variety of applications, from drilling holes to chipping away at existing structures.

On the other hand, the PCH3600GRC is an innovative cordless pancake air compressor that delivers reliable power without the constraints of cords. With its 6-gallon capacity tank and 0.8 SCFM output at 90 PSI, this compressor is ideal for a broad range of air tools. Portability is a prime characteristic of the PCH3600GRC, as it is lightweight and features a handle, making it easy to transport to different job sites.

The compressor also integrates a quiet operation technology, reducing noise levels significantly which is especially beneficial in residential areas or enclosed spaces. Users can expect fewer disturbances while still enjoying a high level of performance. The dual outlet configuration enables multiple tools to be connected simultaneously, enhancing productivity.

In summary, both the Porter-Cable D25806-025-2 and PCH3600GRC represent top-tier engineering and technology innovation. The D25806-025-2 offers substantial power and versatility for heavy-duty tasks, while the PCH3600GRC stands out for its portability and quiet operation, making them essential tools for modern tradespeople and home improvement enthusiasts alike.
Top Page Image Contents