Powermate P-WFT-16022 specifications Technical Service, How to Prepare for Storage

Page 19

Maintenance (Continued)

•Save all instructions

How to Prepare for Storage

WARNING

Never store the trimmer indoors with fuel in the fuel tank. Never store in an enclosed, poorly ventilated area where fumes could reach an open flame, a spark or a pilot light as on a furnace, water heater or clothes dryer. Allow engine to cool before storing unit.

WARNING

Do not remove gasoline while inside a building, near a fire, or while you smoke. Gasoline fumes can cause an explo- sion or a fire.

NOTE: A yearly checkup or tune-up at an authorized service center will make sure that the trimmer will provide maximum performance for the next season.

When the trimmer is put in storage for thirty days or more, the following steps should be followed to make sure the Trimmer is in good condition the next season.

1.Let the engine run until it is out of gasoline.

2.Change the oil by following instructions under “How to

Change the Engine Oil” section.

3.Remove the spark plug from the cylinder. Pour one ounce of oil into the cylinder. Slowly pull the recoil- start grip so that the oil will protect the cylinder. Install a spark plug in the cylinder. Pull recoil slowly until resistance is felt. This will close the cylinder valves.

WARNING

Do NOT attach spark plug wire to spark plug when storing unit.

4.Clean Trimmer. Remove all dirt, leaves, debris, grease, etc. from the Trimmer – including cylinder cooling fins, recoil starter cover holes, under fuel tank, and

under muffler.

5.Check the trimmer for worn or damaged parts. Have damaged parts replaced if necessary.

6.Tighten any loose hardware.

7.Apply lubrication as directed in Maintenance section.

8.Put the unit in a building that has good ventilation.

Technical Service

You may have further questions about assembling, operating, or maintaining this Trimmer. If so, you can contact our Technical Service Department at 1-800-737-2112 (English only).

You may also write to:

METL Corporate Office - CORRESPONDENCE ONLY

 

If you need assistance or have any questions, CALL

 

ATTN: Technical Service – METL

 

 

TOLL FREE: 1-800-737-2112.

625 Barclay Blvd.

 

 

 

 

 

Lincolnshire, IL 60069

 

 

When contacting the Technical Service Department, have ready:

•Your Name

•Your Address

•Your Phone Number

•Model Number of Product

•Date of Purchase (include copy of receipt for written requests)

Questions? Call Toll Free at 1-800-737-2112

18

Copyright © 2009 MAT Engine Technologies, LLC

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Operator’s Manual Field TrimmerControl and Operating Symbols Safety DefinitionsSafety Alert Symbols Safety Warning SymbolsSave all instructions Important Safety InformationFuel Safety Storage Safety Features SpecificationsSave all instructions Unit Engine How to Assemble the Handle AssemblyEngine Oil How to Check Oil Level and Fill to Proper LevelAmbient Service Temperature Engine PreparationFuel How to Fill Engine with FuelOperation How to Start the EngineOperation Save all instructions How to Stop the EngineHow to Engage the Trimmer Head How to Disengage the Trimmer HeadTrimming Tips How to Adjust the Height of CutSlope Guide Service Records MaintenanceService How to Clean the Air Filter How to Change the OilHow to Replace the Trimmer Lines How to Check the Spark Plug How to Replace the Drive Belt How to Prepare for Storage Technical ServiceMetl Corporate Office Correspondence only Problem Possible Causes Solutions TroubleshootingPowermate Field Trimmer Limited Warranty WarrantyYour Warranty Rights and Obligations Emisson Control System WarrantyManufacturer’s Warranty Coverage Limitations of Liability WarrantyHow to Obtain Warranty Service ExclusionsSystems Covered by this Warranty Parts Description Llame sin costo al Manual del usuarioSímbolos de advertencia para seguridad Símbolos de alerta para sequradadSímbolos de control y funcionamiento Conserve todas las instrucciones Instrucciones de seguridad importantesInstrucciones de seguridad importantes la siguiente Seguridad DE Niños Cubierta del arrancador de retroceso Cubre el me EspecificacionesCaracterísticas Conserve todas las instrucciones UnidadCómo montar el asidero MontajeAceite de motor Preparción del motorCombustible Preparción del motor la siguienteAntes de arrancar el motor UsoCómo arrancar el motor Cómo desengranar el cabezal de la segadora Uso la siguiente Conserve todas las instruccionesCómo parar el motor Cómo engranar el cabezal de la segadoraUso la siguiente Guía Para Pendientes Notas Importantes sobre el programa de mantenimiento MantenimientoCómo cambiar el aceite Mantenimiento la siguienteCómo limpiar filtro de aire Cómo cambiar los hilos de la segadora Modelo de bujía Torch F6RTC Cómo revisar la bujíaCómo cambiar la banda del impulsor Cómo preparala para almacenamiento Servicio técnicoWildlife Way Long Grove, IL Conserve todas las instrucciones Problema Diagnóstico y resolución de problemasGarantía limitada de la Segadora Souhland Para Campo Abierto GarantíaCobertura de la garantía del fabricante Garantía la siguiente Conserve todas las instruccionesGarantía del sistema pro control de emisiones contaminantes Derechos y obligaciones al amparo de la garantíaLimitación de responsabilidad Cobertura de la garantíaCómo obtener servicio de garantía ExclusionesGarantía la siguiente California Air Resource Board Powermate Field TrimmerPara Cambiar EL Filtro DE Aire

P-WFT-16022 specifications

The Powermate P-WFT-16022 is a versatile and robust workbench tool designed to elevate the efficiency and convenience of various tasks around the workshop or home. This powerful workbench offers an array of features that cater to both professionals and DIY enthusiasts, making it an essential addition to any workspace.

One of the standout features of the Powermate P-WFT-16022 is its durable construction. Made from high-quality materials, the workbench is designed to withstand heavy use and resist wear and tear over time. The surface is engineered to be scratch-resistant, ensuring that it maintains its appearance and functionality even after extensive handling.

In terms of dimensions, the Powermate P-WFT-16022 provides a generous workspace, allowing users to work on multiple projects simultaneously. Its ample surface area is designed to accommodate a variety of tools and materials, making it ideal for woodworking, metalworking, and other crafting activities. The sturdy legs offer stability and support, ensuring that the workbench remains firmly in place during operation.

One of the technological highlights of the Powermate P-WFT-16022 is its integrated power strip. This feature comes equipped with multiple outlets, allowing users to plug in various tools and appliances without the need for additional extension cords. This not only enhances convenience but also ensures that everything needed for a project is within easy reach.

The P-WFT-16022 also incorporates adjustable height settings, making it customizable to suit the user's preferences or specific tasks. This ergonomic feature can help reduce strain and fatigue during prolonged use, contributing to a more comfortable working environment.

Another noteworthy characteristic of this workbench tool is its portability. The built-in wheels allow users to move the workbench effortlessly from one location to another. This ease of mobility makes it suitable for both workshop settings and on-site jobs, providing flexibility for various tasks.

Overall, the Powermate P-WFT-16022 is an exemplary workbench tool that combines sturdiness, functionality, and advanced features. Its practical design caters to a wide range of applications, ensuring users can tackle projects with confidence and efficiency. Whether for professional use or personal projects, this workbench is a reliable companion that meets the demands of any crafting or repair task.
Top Page Image Contents