Poulan XT185H42LT To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 6)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a fl at level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

"ENGAGED" POSITION ATTACHMENT LIFT LEVER HIGH POSITION

LOW

POSITION

DEFLECTOR

SHIELD

ATTACHMENT

CLUTCH LEVER "DISENGAGED" PO-

SITION

FIG. 7

GAUGE

WHEEL

MOUNTING

BRACKET

 

014

 

2

3/8-16

3

 

LOCKNUT

 

3/8 WASHER

SHOULDER

BOLT

 

 

GAUGE WHEEL

FIG. 6

TO OPERATE MOWER (See Fig. 7)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Move motion control lever to neutral (N) position.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before and while backing.

•Slowly move motion control lever to reverse (R) position to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

ROS "ON" POSITION

ENGINE "ON" POSITION

 

(NORMAL OPERATING)

02828

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

12• Avoid stopping or changing speed on hills.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents XT185H42LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig Using the Reverse Operation SystemTo Operate Mower See Fig Reverse Operation System ROSBefore Starting the Engine To Transport See FigsCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Maintenance Lubrication ChartTractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal To Check and Adjust Brake See Fig Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Brake To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

XT185H42LT specifications

The Poulan XT185H42LT is a robust riding lawn mower designed for homeowners seeking efficiency and reliability in their lawn care routine. With its powerful engine and user-friendly features, the XT185H42LT is an excellent choice for maintaining medium to large-sized lawns.

At the heart of the XT185H42LT is its high-performance 18.5 horsepower Briggs & Stratton engine. This engine provides ample power to tackle thick grass and uneven terrain, ensuring a clean and even cut every time. The engine is designed for durability and easy maintenance, with features that simplify oil changes and filter replacements.

The mower boasts a 42-inch steel cutting deck, which allows for wider cutting paths, reducing the number of passes needed to mow the lawn. This feature not only saves time but also enhances efficiency. The cutting deck offers a range of cutting heights, which can be easily adjusted to suit different grass types and conditions, ensuring optimal performance throughout the mowing season.

One of the standout technologies included in the XT185H42LT is its infinitely variable speed transmission. This allows users to control the mowing speed seamlessly, adapting to varying lawn conditions and ensuring that even challenging areas can be mowed effectively. The raceway steering makes maneuverability effortless, allowing the user to navigate around obstacles like flower beds, trees, and garden ornaments with ease.

Comfort and convenience are key aspects of the XT185H42LT. The mower features an ergonomic seating position, with a plush high-back seat designed to reduce fatigue during longer mowing sessions. Easy-access controls are strategically placed to allow for smooth operation, and the built-in cup holder adds a touch of convenience for extended use on warm days.

Additional features include a quick-release deck for easy cleaning and maintenance, as well as a mulching capability that finely chops clippings, returning vital nutrients to the lawn. Overall, the Poulan XT185H42LT combines power, efficiency, and user comfort, making it a versatile choice for homeowners looking to optimize their lawn maintenance efforts. Whether tackling daily mowing tasks or handling larger projects, the XT185H42LT delivers performance and reliability every time.
Top Page Image Contents