Assembly Information Weed, Weed Blade | Poulan 530164264 specification

ASSEMBLY INFORMATION - WEED	INSTALLATION OF THE METAL
BLADE	BLADE

WEED

BLADE

NOTE: Remove the trimmer head and plastic shield before attaching the metal shield and installing the weed blade. To remove the trimmer head, align hole in the dust cup with the hole in the side of the gearbox by rotating the dust cup. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loos- ening the trimmer head. Remove the trimmer head by turning clockwise. Remove the screw- driver. To remove the plastic shield, loosen and remove wing nut. Pivot shield to release bracket from slot. See INSTALLATION OF THE TRIM- MER HEAD and ATTACHING THE PLASTIC SHIELD for illustrations. Be sure to store all parts and instructions for future use. Never use the trimmer head with the metal blade installed.

ATTACHING THE METAL SHIELD

WARNING: The metal shield must be properly installed on the tool anytime the tool is used with a blade. The forward tip of the metal shield helps to reduce the occurrence of blade thrust which can cause serious injury such as amputation to the operator or by- standers. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the shaft.

1.Place the metal shield under the gearbox, and align the screw holes.

Gearbox

Shield

2.Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and secure- ly with the hex wrench provided.

WARNING: Wear protective gloves when handling or performing maintenance on the blade to avoid injury. The blade is sharp and can cut you even when it is not moving.

WARNING: Do not use any blades, or fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by Poulan/Weed Eater and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others.

NOTE: The dust cup and retaining washer are located on the gearbox shaft and not in the parts bag. All other fasteners mentioned in the follow- ing assembly steps are in the parts bag.

1.Remove the retaining washer from the threaded shaft of the gearbox. Leave the dust cup on the shaft.

2.Install the blade and the retaining washer over the threaded shaft.

3.Make sure the raised part of the retaining washer is facing the gearbox and the raised area fits into the hole in the center of the blade.

4.Slide the blade and retaining washer onto the shaft of the gearbox.

5.Place the cupped washer onto the shaft. Make sure the cupped side of the washer is toward the blade.

6.Install the blade nut by threading onto the shaft counterclockwise.

Gearbox

Shield

Dust Cup	Threaded Shaft
	Threaded Shaft
Retaining	Blade
Retaining
Washer
Cupped
Washer	Nut
	Nut

NOTE: Make sure all parts are in place as illus- trated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer.

7.Align hole in dust cup with hole in side of gearbox by rotating the blade.

8.Insert a small screwdriver into aligned holes. This will keep the shaft from turn- ing while tightening the blade nut.

530164264 specifications

The Poulan 530164264 is a high-quality replacement chain designed for professionals and enthusiasts in the field of forestry and landscaping. Renowned for its cutting efficiency and durability, this chain is a smart investment for maintaining chain saw performance and effectiveness.

One of the main features of the Poulan 530164264 is its design, which utilizes precision-engineered components to ensure optimal performance. The chain is built for compatibility with various models of Poulan chain saws, providing versatility for users with multiple tools. The design incorporates a .325-inch pitch and a gauge of .058 inches, which strikes a perfect balance between cutting speed and control, making it ideal for tackling both small and medium-sized trees.

The construction of the Poulan 530164264 chain includes high-quality steel links, which enhance the chain’s lifespan while improving its resistance to wear and tear. This durability is essential for users who depend on their equipment for daily tasks, as it minimizes the frequency of replacements and maintenance. Additionally, the chain features heat-treated components, which strengthen its resilience against the rigors of heavy use and extend its operational lifespan.

A notable technology integrated into the Poulan 530164264 is the low-vibration design. This feature reduces fatigue for users during prolonged operation, ensuring a more comfortable and efficient cutting experience. By minimizing vibration, the chain also promotes smoother cuts, improving overall efficiency and effectiveness.

Another key characteristic of the Poulan 530164264 is its easy-to-sharpen design. The chain can be re-sharpened quickly and conveniently, allowing users to maintain optimal cutting performance without significant downtime. This characteristic is particularly beneficial for professional users who require their equipment to remain operational throughout the workday.

In summary, the Poulan 530164264 replacement chain stands out with its precision design, durability, and user-friendly features. Built for efficiency, the chain’s low-vibration technology, heat-treated construction, and compatibility with multiple Poulan models make it a reliable choice for both professionals and hobbyists. Whether you are clearing brush, cutting firewood, or tackling larger tree jobs, the Poulan 530164264 is engineered to deliver exceptional performance, ensuring you can stay productive and comfortable in all your cutting endeavors.