Orbit Manufacturing p 801 295 9820, 91916 Using the Remote Control Device, To Water All Stations

Page 12

the current station to the next station in the cycle. This can be done during scheduled, manual, or remote actuated watering.

Section 4: Using the Remote

Control Device

NOTE: The timer will accept commands from the remote control device only when the selection dial is turned to AUTO or OFF. (If the selection dial is turned to any other setting, commands from the Remote Control Device will be stored in memory and executed when the selection dial is turned to AUTO).

Install a Battery in the Remote Control Device:

•Open the battery compartment door.

•Install a 9-volt battery in the battery compartment.

•Replace the battery compartment door.

To Synchronize the Remote Control Device with the Timer:

The remote device provided with your timer is already synchro- nized to your timer. If the remote is not functioning properly or if you are adding a new remote or RF sensor to your system do the following:

•With the remote device in your hand press the “RF Sync” button on the timer (this will activate a red light on

the timer).

07WTM002598 57926-24 rA.indd 11

•	Press the OFF button on the remote or depress the stem of	ENGLISH
•	Press the OFF button on the remote or depress the stem of
	the RF sensor (the red light should start blinking).
•	If the red light blinks you have successfully synchronized the
	devices. If the light does not blink check that the remote has a
	fresh 9V battery or that the RF sensor switch is not OFF and
	try the steps again.

To Water All Stations:

•Press and release the ALL button on the remote control device to select all stations for watering.

•Press and release the ON “X” MIN button to command the timer to water all the stations sequentially for the desired (“X”) number of minutes.

•If you wish to advance to the next station before a station's watering duration is complete, press NEXT.

To Water One Station:

•Press the number of the station you wish to water.

•Press ON "X" MIN to water the station for the desired ("X") number of minutes.

To Water More Than One Specific Station:

•Press the numbers of the stations you wish to water. (Example: 3, 7, 10, and 6. The timer will water in sequence from lowest to the highest. 3, 6, 7, 10.) (No matter which order you press the keys, the timer will water them sequentially from the lowest to the highest number.)

11

2/16/07 2:07:22 PM

Image 12

Contents Page ST2-RF Sprinklertimer Manual Table of Contents Commonly Used Controls Getting Started About This ManualReset the Timer Activating the BatteriesSelect the Preferred Language Set the Time of Day and DateProgramming Your Timer Determine a Watering PlanSet Start Times Set Station Watering DurationsSet the Timer to Automatically Run Your Programs Set Watering DaysTo Turn All Watering Off To Prevent Watering on a Particular Day To Prevent Watering During a Particular Period of the Day Set Water BudgetingTest All Stations Manual Watering All StationsManual Watering Program a Rain Delay Function Manual Watering Program BManual Watering Single Stations Manual Advance During WateringUsing the Remote Control Device To Synchronize the Remote Control Device with the TimerTo Water All Stations To Water One StationUsing the Optional Rain-Freeze Sensor Installing the Sprinkler Timer Five Easy StepsReturns control back to the timer Select a LocationDo not slide the timer back onto the docking port yet Two power leads from the transformer into eachWire the Electric Valves Mount the Docking PortConnecting Sprinkler Wire Mount the Sleeve for the Remote Control DeviceDiagnostics Circuit Breaker Smart-ScanDiagnostic Fault SensingFault Notification Correcting the FaultGlossary of Terms Term DefinitionPlants Trouble Shooting Symptom Possible Causes of Problems CorrectionOrbit Irrigation Limited Six-Year Warranty HelpListings Características y funciones importantes Instalación en interiores del temporizador delPC Programable Programas dobles Seis ciclos de horas de inicio por programaControles comúnmente utilizados Sobre este manual Programación de los botonesReiniciación pequeño agujero Esfera de selecciónSección 2 Primeros pasos Activación de las bateríasSeleccione el idioma Configure los horarios de comienzo Coloque la hora del día y la fechaDetermine un plan de riego Ver Pág para las instruccionesConfigure para regar días impares Configure para regar días paresColoque la duración del riego de la estación Establezca los días de riegoPara desactivar todo el riego Para impedir el riego en un día en particularEstablezca el intervalo de riego Gire la esfera de selección a DÍA/PERÍODO SIN RiegoEstablezca el presupuesto de riego Pruebe todas las estacionesRiego manual Todas las estaciones Presione el botón Ingresar . En el selector apareceRiego manual Programa a Riego manual Programa BPresione Siguiente Avanzar rápidamente de una estación a la siguiente presioneRiego manual Estaciones individuales Función de retardo por lluviaAvance manual durante el riego Coloque una batería en el dispositivo de control remotoPara regar todas las estaciones Para regar una estaciónPara regar más de una estación específica Sección 5 Uso del sensor Lluvia-helada opcional En un área interna y seca, donde la temperatura deMonte la base de acoplamiento Elija el lugarConecte el transformador Realice el cableado de las válvulas eléctricasMonte el estuche para el control remoto Válvulas de EstaciónSección 7 Interruptor de circuito con diagnóstico Detección y diagnóstico de fallas Smart-ScanAviso de falla Cómo corregir la fallaSección 8 Glosario de términos Término DefiniciónDetermine un plan de riego Plantas Sección 9 Solución de problemas Síntoma Posible causa del problema CorrecciónAsistencia Clasificación