Scag Power Equipment SCR manual HOPPER, Mulch or Side Discharge Operation, Parking the Mower

Page 17

Section 4

SCR 2K IOS

Figure 4-7 Improper Operation on a Slope

4.Fill the fuel tank with fresh, clean fuel at the end of every day of operation.

5.Check the tire pressure. Inflate tires if necessary.

4.10HOPPER, MULCH or SIDE DISCHARGE OPERATION

When mowing with the cutting deck setup for rear discharge into the hopper, the blower belt must be installed. A control lever located on the left side of the tractor (Figure 4-8) will release tension on the idler pulley to allow the belt to be installed (grass catching operation) or removed (mulching or side discharge operations). The cutter deck must also be adapted to the type of cutting that the operator is attempting to perform.

4.8 PARKING THE MOWER

1.Place the speed control in the neutral position.

2.Slow the engine to idle speed.

3.Engage the parking brake.

4.Turn the ignition key to the OFF position and remove the key.

4.9 AFTER OPERATION

1.Wash the entire mower after each use. Do not use high pressure spray or direct the spray onto electrical components.

-IMPORTANT-

Do not wash a hot or running engine. Cold water will damage the engine. Use compressed air to clean the engine if it is hot.

2.Keep the entire mower clean to inhibit serious heat damage to the engine or hydraulic oil circuit.

3.Check the drive belts for proper alignment, correct if necessary. Remove any debris build up.

Blower Belt

Blower Belt

Release Pedal

SCR 2K BBR

Figure 4-8 Blower Belt Release

Rear Discharge

Baffle

SCR 2K RD

Side Discharge

Shutoff Baffle

Figure 4-9 Baffles for Rear Discharge

13

Image 17

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Introduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsBefore Operation Considerations Safety InformationSignal Words Operation Considerations Do not turn sharply. Use care when backing up Maintenance ConsiderationsInstall Belt Cover Before Operating Machine Safety and Instructional DecalsEngine SpecificationsElectrical TractorTractor Contd Weights and DimensionsCutter Deck Grass Catching SystemControls and Instrument Identification Operating InstructionsBlower Belt Release Safety Interlock SystemGround Travel and Steering Starting the EngineReverse Travel Forward TravelHillside Operation Engaging the Deck Drive Cutter BladesAfter Operation HOPPER, Mulch or Side Discharge OperationParking the Mower 10 Tailgate Operation Grass Catching OperationRemoving Clogged Material Side Discharge OperationMulching Operation Recommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Deck Locking Pin Locking Pin Hole Tilting the Cutter DeckCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdParking Brake Adjustment AdjustmentsTravel Adjustments Neutral AdjustmentStart the engine and disengage the parking brake Drive linkage Tracking Adjustment Steering Handle AdjustmentBelt Adjustment Throttle Control and Choke AdjustmentsCutter Deck Adjustments Belt AlignmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelChecking Engine Crankcase Oil Level Changing Engine Oil Filter Changing Engine Crankcase OilEngine Fuel System Filling the Fuel TankChecking Electrolyte Level and Cleaning Battery BatteryEngine AIR Cleaner Cleaning and/or Replacing Air Cleaner ElementJump Starting Charging the BatteryDrive Belts Blade ReplacementCutter Blades Blade InspectionHopper TiresCutter Deck Gearbox Checking Lubricant Level10 Gearbox Drain Plug Power Unit Gearbox13 Fluid Level BODY, DECK, Hopper and UpholsteryPage Cutter Deck Part Number Description Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Engine and Attaching Parts Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Electrical System Part Number Description Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Rotating Blades and Belts Replacement Decals and Information PlatesSCR 2K RD2 Electrical Schematic Page Limited Warranty Commercial Equipment 1999