Scag Power Equipment SCR manual Safety and Instructional Decals

Page 9

Section 2

2.6 SAFETY AND INSTRUCTIONAL DECALS

DANGER

SPINNING BLADE

KEEP CLEAR

CONTACT CAN INJURE

48071

WARNING

ROTATING BLADES AND BELTS

KEEP HANDS, FEET & CLOTHING CLEAR

KEEP ALL GUARDS IN PLACE

SHUT OFF ENGINE & DISENGAGE BLADE CLUTCH BEFORE SERVICING

CLEAR AREA OF DEBRIS BEFORE MOWING

USE CAUTION IN DIRECTING DISCHARGE

KEEP BYSTANDERS, CHILDREN & PETS AWAY

READ INSTRUCTION MANUAL BEFORE OPERATING DO NOT OPERATE WITHOUT DISCHARGE CHUTE, MULCHING

KIT, OR ENTIRE GRASS CATCHER INSTALLED

481040

CAUTION

KEEP BYSTANDERS AWAY

CAUTION

BEFORE OPERATING

READ OPERATINGS

MANUAL AND SAFETY

INSTRUCTIONS

5

WARNING

INSTALL BELT COVER BEFORE

OPERATING MACHINE

READ OPERATOR'S MANUAL

481039

CAUTION

AVOID INJURY FROM

BURNS. SHUT OFF

ENGINE BEFORE

REMOVING FUEL
TANK CAP.	481272

Image 9

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Introduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsSafety Information Signal WordsBefore Operation Considerations Operation Considerations Do not turn sharply. Use care when backing up Maintenance ConsiderationsInstall Belt Cover Before Operating Machine Safety and Instructional DecalsEngine SpecificationsElectrical TractorTractor Contd Weights and DimensionsCutter Deck Grass Catching SystemControls and Instrument Identification Operating InstructionsBlower Belt Release Safety Interlock SystemGround Travel and Steering Starting the EngineReverse Travel Forward TravelHillside Operation Engaging the Deck Drive Cutter BladesHOPPER, Mulch or Side Discharge Operation Parking the MowerAfter Operation 10 Tailgate Operation Grass Catching OperationSide Discharge Operation Mulching OperationRemoving Clogged Material Adjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Deck Locking Pin Locking Pin Hole Tilting the Cutter DeckCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdParking Brake Adjustment AdjustmentsTravel Adjustments Neutral AdjustmentStart the engine and disengage the parking brake Drive linkage Tracking Adjustment Steering Handle AdjustmentBelt Adjustment Throttle Control and Choke AdjustmentsCutter Deck Adjustments Belt AlignmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Checking Hydraulic Oil Level Checking Engine Crankcase Oil LevelChanging Hydraulic Oil Changing Engine Oil Filter Changing Engine Crankcase OilEngine Fuel System Filling the Fuel TankChecking Electrolyte Level and Cleaning Battery BatteryEngine AIR Cleaner Cleaning and/or Replacing Air Cleaner ElementJump Starting Charging the BatteryDrive Belts Blade ReplacementCutter Blades Blade InspectionHopper TiresCutter Deck Gearbox Checking Lubricant Level10 Gearbox Drain Plug Power Unit Gearbox13 Fluid Level BODY, DECK, Hopper and UpholsteryPage Cutter Deck Part Number Description Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Engine and Attaching Parts Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Electrical System Part Number Description Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Rotating Blades and Belts Replacement Decals and Information PlatesSCR 2K RD2 Electrical Schematic Page Limited Warranty Commercial Equipment 1999