Scag Power Equipment SCR manual Changing Engine Crankcase Oil, Changing Engine Oil Filter

Page 34

Section 7

Engine Oil

Filler Cap

Engine Oil

Dip Stick

SCR 2K FCDS

Figure 7-3 Engine Fill Cap and Dip Stick

B. Changing Engine Crankcase Oil

After the first 5 hours of operation, change the engine crankcase oil and replace the oil filter. Thereafter, change the engine crankcase oil after every 100 hours of operation or bi-weekly, whichever occurs first. Refer to the Engine Operator’s Manual furnished with this mower for specific instructions.

Engine Oil

Drain Plug

SCR 2K EODP

Figure 7-4 Engine Oil Drain Plug

C. Changing Engine Oil Filter

After the first 5 hours of operation, replace the engine oil filter. Thereafter, replace the oil filter after every 200 hours of operation or every month, whichever occurs first. Refer to Engine Operator’s Manual for specific instructions.

7.5 ENGINE FUEL SYSTEM

To avoid injury from burns, allow the mower to cool before removing the fuel tank cap and refueling.

Engine Oil

Filter

SCR 2K EOF

Figure 7-5 Engine Oil Filter

A. Filling the Fuel Tank

Fill the fuel tank at the end of each operating day to within 1 inch below the filler neck. Do not overfill. Use clean, fresh unleaded gasoline with a minimum octane rating of 87.

B. Replacing In-Line Fuel Filter Element

The in-line fuel filter (Figure 7-6) should be replaced after every 500 hours of operation or annually, whichever occurs first.

1.Close the shutoff valve. Remove the two clamps securing the fuel filter to the fuel hose. Remove the fuel filter.

30

Image 34

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Direction Reference General InformationIntroduction Servicing the Engine and Drive Train ComponentsSignal Words Safety InformationBefore Operation Considerations Operation Considerations Maintenance Considerations Do not turn sharply. Use care when backing upSafety and Instructional Decals Install Belt Cover Before Operating MachineElectrical SpecificationsEngine TractorCutter Deck Weights and DimensionsTractor Contd Grass Catching SystemOperating Instructions Controls and Instrument IdentificationSafety Interlock System Blower Belt ReleaseStarting the Engine Ground Travel and SteeringForward Travel Reverse TravelEngaging the Deck Drive Cutter Blades Hillside OperationParking the Mower HOPPER, Mulch or Side Discharge OperationAfter Operation Grass Catching Operation 10 Tailgate OperationMulching Operation Side Discharge OperationRemoving Clogged Material Moving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Tilting the Cutter Deck Deck Locking Pin Locking Pin HoleTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundAdjustments Parking Brake AdjustmentNeutral Adjustment Travel AdjustmentsStart the engine and disengage the parking brake Tracking Adjustment Steering Handle Adjustment Drive linkageCutter Deck Adjustments Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentMaintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Checking Engine Crankcase Oil Level Checking Hydraulic Oil LevelChanging Hydraulic Oil Engine Fuel System Changing Engine Crankcase OilChanging Engine Oil Filter Filling the Fuel TankEngine AIR Cleaner BatteryChecking Electrolyte Level and Cleaning Battery Cleaning and/or Replacing Air Cleaner ElementCharging the Battery Jump StartingCutter Blades Blade ReplacementDrive Belts Blade InspectionCutter Deck Gearbox TiresHopper Checking Lubricant LevelPower Unit Gearbox 10 Gearbox Drain PlugBODY, DECK, Hopper and Upholstery 13 Fluid LevelPage Cutter Deck Part Number Description Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Engine and Attaching Parts Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Electrical System Part Number Description Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Replacement Decals and Information Plates Rotating Blades and BeltsSCR 2K RD2 Electrical Schematic Page Limited Warranty Commercial Equipment 1999