Scag Power Equipment SCR manual BODY, DECK, Hopper and Upholstery, Fluid Level

Page 40

Section 7

FLUID LEVEL

SCR 2K DS

Figure 7-13 Fluid Level

B. Changing Lubricant

The lubricant in the power unit gearbox should be changed after every 500 hours of operation or yearly, whichever occurs first.

1.Beneath the power unit is an access hole to the gearbox drain plug. Clean the area thoroughly and place a suitable container under the drain plug.

2.Remove the drain plug and drain the lubricant into the container and properly discard.

3.Reinstall the drain plug and add EP-80/90 lubricant through the dipstick tube. Approximately 6 ounces of fluid will be needed to fill the gearbox. Follow the procedure in section 7.13 A. Checking Lubricant Level, to fill the gearbox to the proper level.

7.14BODY, DECK, HOPPER AND UPHOLSTERY

CAUTION:

Do not wash any portion of the equipment while it is hot. Do not wash the engine; use compressed air.

1.After each use, wash the mower, deck and hopper. Use cold water and automotive cleaners. Do not use pressure cleaners.

2.Do not spray electrical components.

3.Use a mild soap solution or a vinyl/rubber cleaner to clean the seat.

4.Repair damaged metal surfaces and use Scag touch- up paint available from your authorized Scag dealer. Wax or polish the mower for maximum paint protection.

36

Image 40

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd General Information IntroductionDirection Reference Servicing the Engine and Drive Train ComponentsSignal Words Safety InformationBefore Operation Considerations Operation Considerations Maintenance Considerations Do not turn sharply. Use care when backing upSafety and Instructional Decals Install Belt Cover Before Operating MachineSpecifications EngineElectrical TractorWeights and Dimensions Tractor ContdCutter Deck Grass Catching SystemOperating Instructions Controls and Instrument IdentificationSafety Interlock System Blower Belt ReleaseStarting the Engine Ground Travel and SteeringForward Travel Reverse TravelEngaging the Deck Drive Cutter Blades Hillside OperationParking the Mower HOPPER, Mulch or Side Discharge OperationAfter Operation Grass Catching Operation 10 Tailgate OperationMulching Operation Side Discharge OperationRemoving Clogged Material Moving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Tilting the Cutter Deck Deck Locking Pin Locking Pin HoleTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Scalloped Cut, or Rough ContourTroubleshooting Contd GroundAdjustments Parking Brake AdjustmentNeutral Adjustment Travel AdjustmentsStart the engine and disengage the parking brake Tracking Adjustment Steering Handle Adjustment Drive linkageThrottle Control and Choke Adjustments Belt AdjustmentCutter Deck Adjustments Belt AlignmentMaintenance Maintenance Chart Recommended Service IntervalsMaintenance Chart Recommended Service Intervals Contd Lubrication Grease Fitting Lubrication Chart see FigureLubrication Fitting Points Checking Engine Crankcase Oil Level Checking Hydraulic Oil LevelChanging Hydraulic Oil Changing Engine Crankcase Oil Changing Engine Oil FilterEngine Fuel System Filling the Fuel TankBattery Checking Electrolyte Level and Cleaning BatteryEngine AIR Cleaner Cleaning and/or Replacing Air Cleaner ElementCharging the Battery Jump StartingBlade Replacement Drive BeltsCutter Blades Blade InspectionTires HopperCutter Deck Gearbox Checking Lubricant LevelPower Unit Gearbox 10 Gearbox Drain PlugBODY, DECK, Hopper and Upholstery 13 Fluid LevelPage Cutter Deck Part Number Description Cutter Deck Support Components Cutter Deck Support Components Sheet Metal Sheet Metal Blower Assembly Blower Assembly Engine and Attaching Parts Engine and Attaching Parts Traction Drive Components Part Description Hydraulic Pump Housing Kit Includes Housing, Journal Bearing Cutter Deck Drive Gearbox Ref. Part No. No. Description Speed and Steering Controls Part Description Parking Brake Mechanism Parking Brake Mechanism Fuel and Hydraulic Components Ref. Part No. Number Description Electrical System Part Number Description Hopper Hopper Hopper Actuator Mechanism Ref. Part No. Number Description Replacement Decals and Information Plates Rotating Blades and BeltsSCR 2K RD2 Electrical Schematic Page Limited Warranty Commercial Equipment 1999