ResMed VPAP Adapt SV manual Glossary

Page 32

Problem

Possible cause

Solution

 

 

 

No LCD display

Power not connected or

Ensure the power cable is

 

switch at back is not on.

connected, and that the

 

 

switch at the back of the unit

 

 

is in the ’on’ position.

 

 

 

FAULT message displayed

Internal malfunction.

Return the device to your

on LCD

 

equipment supplier for

 

 

service.

System Error 7 message

Device power-on has been

 

interrupted by breathing into

 

the mask during warm up.

Turn the flow generator off and on again. Do not place mask on face during warm up (30 seconds). Select LEARN CIRCUIT (page 21). If the error is not cleared, contact your equipment supplier for service.

Internal malfunction.

Return the device to your

 

equipment supplier for

 

service.

 

 

Glossary

Alarms

When more than one alarm is activated at the one time, the highest priority alarm will be displayed.

Backlight

The backlight turns off if no button has been pressed for two minutes. It can also be kept permanently on by selecting On in the Backlight screen of the Options menu.

bpm

breaths per minute

L/min

liters per minute

Mean

The average value of the monitored parameter.

Minute ventilation

A measure of the respiratory rate x tidal volume.

Proximal cuff

A connector between the air tubing and the mask. The pressure sensor tub- ing attaches to the proximal cuff so that pressure at the mask can be detected and monitored.

SmartStart

A feature that starts the VPAP Adapt SV automatically when you breathe into the mask.

32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents Vpap Adapt SV Contents Introduction Vpap Adapt SVUser/Owner Responsibility DefinitionsVpap Adapt SV Quick Setup Guide Vpap Adapt SV System Vpap Adapt SV ComponentsMasks Connect this endConnect this end to To the mask Flow generatorConnect the power cord Assembling the Vpap Adapt SV SystemAttach the mask to the air tubing Front view of Vpap Adapt SVDo not tip the humidifier while it is connected to Connecting a HumidifierHumidifiers HumidAire HumidAire 2i attached to the Vpap Adapt SVHumidAire English ResLink Anti-bacterial FilterUsing DC Power to Run the Vpap Adapt SV Supplemental OxygenUsing the Vpap Adapt SV Standby ModeStarting Treatment Stopping TreatmentControl Panel Functions LCD screenStart/Stop key Up/Down keyAdjusting Settings Alarm LEDs and Alarm muteLeft key green Right key redYou wish to change the setting for the mask you are using ExampleMenus Navigating the Patient menuLearn Circuit Settings MenuMask Ramp Cpap mode only Results MenuSmartStop Leak AlertOptions Menu Treatment Screens Servicing MenuAlarms Low Mask Pressure AlarmIf a low pressure alarm sounds Triggered byPower Fail Alarm High Pressure / High Average Pressure AlarmsHigh Leak Alert Insufficient Pressure Support AlarmFlow Blocked Alarm Weekly Cleaning and MaintenanceDaily Air tubing assembly removed for cleaning PeriodicallyAir Filter ServicingHypoallergenic Air Filter Fitting the filterTroubleshooting Servicing Australia and New ZealandGlossary Technical Specifications IEC 601-1 classifications Alarm specificationsInspiratory Trigger Characteristics Glossary of symbols Mass flow sensorEmissions test Compliance Next Portable and mobile RF communications Separation distance according to frequency of transmitter Limited Warranty Index Index

VPAP Adapt SV specifications

The ResMed VPAP Adapt SV is a cutting-edge device designed to improve the quality of life for patients suffering from complex sleep apnea conditions, including central and obstructive sleep apnea. It combines advanced technology with user-friendly features to provide effective therapy while ensuring maximum comfort for users.

A standout feature of the VPAP Adapt SV is its Adaptive Servo-Ventilation (ASV) algorithm. This proprietary technology continuously monitors a patient’s breathing patterns and adjusts the airflow accordingly. By providing just the right amount of pressure support during inhalation and maintaining a minimal backup rate during exhalation, the device ensures optimal ventilation while minimizing the risk of over-ventilation. This responsiveness is crucial for patients who may experience fluctuating airway resistance and varying degrees of respiratory events.

The VPAP Adapt SV is equipped with a sophisticated data management system that tracks treatment progress in real time. It automatically collects information about usage, leak rates, and overall pressure settings, which can be easily accessed and reviewed by healthcare providers. This data-driven approach facilitates personalized treatment adjustments, empowering both patients and clinicians to make informed decisions.

Comfort is enhanced through various design features, including a quiet operation mechanism that minimizes noise disruption during sleep. The device offers a range of pressure settings that can be tailored to individual needs, allowing for a comfortable therapeutic experience. The VPAP Adapt SV is compatible with ResMed’s range of CPAP masks, which are ergonomically designed to fit securely without compromising comfort.

Another notable characteristic is its user-friendly interface, which simplifies the setup and adjustments needed for optimal therapy. Patients can easily navigate through various options on the bright display screen, making it accessible for users of all ages.

Additionally, the VPAP Adapt SV’s compact design makes it a portable option for those who travel frequently. It comes with a carrying case and can operate on both AC and DC power sources, ensuring that patients can maintain their therapy wherever they go.

In conclusion, the ResMed VPAP Adapt SV represents a significant advancement in respiratory therapy. With its Adaptive Servo-Ventilation technology, comprehensive data management, and focus on patient comfort, it provides a holistic approach to managing complex sleep apnea, making it a preferred choice for healthcare providers and patients alike.
Top Page Image Contents