Scag Power Equipment SWZU manual Steering Control ROD Adjustment, Tracking Adjustment

Page 16

4.Starting on the left side of the machine, using the adjustment wrench located on the left side of the machine, rotate the tracking adjustment nut counter clockwise just until the LH wheel starts to creep forward. Make a note of the position of the adjust- ment nut. (See Figure 9)

5.Turn the adjustment nut clockwise just until the wheel turns rearward. Make a note of the position of the adjustment nut. To adjust neutral, split the difference between the two noted positions of the adjustment nut. Repeat on the right side as needed.

6.Place the wrench in the holder on the left side of the machine and turn the engine off.

T		TRACKING
	ADJUSTMENTOPERATU
SEE
FAS		N	AL	OR'S

		SLOW

390s0198-1

Figure 10. Control Rod Adjustment

3.Reinstall the speed control spring onto the swivel. Install the hair pin onto the swivel. (See Figure 10)

Figure 9. Neutral Adjustment

STEERING CONTROL ROD

ADJUSTMENT

-NOTE-

This adjustment is made to allow the steering control levers to be moved out of the neutral latch without engaging reverse.

Before making this adjustment be sure that the speed control bearing is just touching the speed control cam and that the bellcrank bearing is resting in the center groove of the neutral cam.

1.Remove the speed control spring. Remove the steering control rod swivel hair pin. Check the location of the swivel in the slotted hole in the bell crank.

2.Turn the swivel joint on the steering control rods until the swivel joint is centered in the slot in the bellcrank.

TRACKING ADJUSTMENT

-NOTE-

Before proceeding with this adjustment, be sure that the tire pressures are correct. (see page 7) and that the neutral adjustment and the steering control rod adjustment have been completed.

1.With the machine on a flat level surface, start the engine and place the speed adjustment lever into the speed that will most often be used.

2.Squeeze the steering control levers and release the neutral latch. Slowly release the steering control levers, allowing the machine to move forward.

WARNING:

BEFORE ATTEMPTING TO MAKE ANY TRACKING ADJUSTMENTS:

1.Move the speed adjustment lever to the neutral position.

2.Place the blade engagement switch in the OFF position.

3.Apply the parking brake.

4.Move the steering control levers into the neutral position.

12

Image 16

Contents Model Swzu 2003Remember Your Mower is only AS Safe AS the Operator Table of Contents Illustrated Parts List 44-45General Information IntroductionDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow General Safety Information Safety InformationBefore Operation Considerations Rotating Blades Before Operation Considerations ContdOperation Considerations Maintenance and Storage Mower Operation Use gasoline with an octane rating no less thanCutter Deck Belt Adjustments Cutter Deck AdjustmentsCustom-Cut Baffle Adjustment Cutter Deck Pitch AdjustmentsCutter Blades Neutral Adjustment To Adjust the Custom-Cut Baffle heightTracking Adjustment Steering Control ROD AdjustmentApply the parking brake Tracking Adjustment Parking BrakeLubrication & Maintenance Hydraulic System Checking Hydraulic Oil LevelChanging Hydraulic Oil Changing Hydraulic Oil Filter ElementEngine Air Cleaner Checking Electrolyte Level and Cleaning BatteryChecking Engine Crankcase Oil Level Changing Engine Crankcase OilCharging the Battery Jump StartingTroubleshooting Cutting Conditions Cause CureCondition Cause Cure Scalping Blades Hitting Dirt or Cutting Very Close toGround Step CutTechnical Specifications EnginesEngine Deck Drive SystemApproximate Dimensions SWZU36A SWZU48A SWZU52A SWZU61A Additional Specifications Optional ITEMS/ATTACHMENTSCutter Decks Page 36A Cutter Decks Ref. Part No. Number Description 48A, 52A & 61A Cutter Decks Part Description 36A Deck Frame 36A Deck Frame 48A and 52A Deck Frame Small Frame 48A and 52A Deck Frame *SMALL Frame Ref. Part Description52A & 61A Deck Frame Large Frame 52A & 61A Deck Frame *LARGE Frame Part Description 52A 61AEngine Deck Engine Deck Part DescriptionDrive and Brake Components 15KA 17KA 21KAE 18KH 18HN Handle Assembly Small Frame Handle Assembly *SMALL Frame Handle Assembly Large Frame SWZU-21KAE Part Description Hydraulic Assembly Hydraulic Assembly Part Number DescriptionHydraulic Pump Assembly BDP-10L117 Hydraulic Pump Assembly Wire Harness Handle Wire Harness Manual StartKohler 18 HP Ground Kawasaki 15 HP & 17 HPHandle Wiring Harness Kawasaki Electric Start Part no Wire Harness Adapter Replacement Decals & Information Heavy-DutySwzu 15KA, 17KA & 18HN Swzu 18KH Swzu 21 KAE Limited Warranty Commercial Equipment Comercial Equipo Limitada Garantía SWZU61A SWZU52A SWZU48A APROXIMADASSWZU36A Dimensiones Continuación Técnicas EspecificacionesOpcionales ARTÍCULOS/ACCESORIOS Adicionales EspecificacionesTécnicas Especificaciones Transmisión DE SistemaCorte DE Condiciones LAS EN Fallas DE Identificación Solución Causa CondiciónCorte de trayectoria La de ancho loInclinadas Salientes Irregular perfil oCorte de trayectorias Pasadas entre cortar sin céspedDe Franjas Vetas La en cortar sin céspedBatería la de Carga Puente por ArranqueCarga la durante producidos gases Batería de limpieza Electrolito de nivel del VerificaciónBaterías manipular de después manos Las y chispas las arcos, los Mantenga .bateríasAceite de filtro del elemento del Cambio HidráulicoHidráulico aceite de Cambio Hidráulico aceite de nivel el VerificarMantenimiento Y Lubricación Precaución Alineación de Ajuste .11 FiguraNeutral Ajuste .9 Figura CON DE Varilla LA DE AjusteVelocidad de ajuste de palanca la Mueva Neutral Ajuste Corte de deflector del 4 Posición .8 FiguraCuchillas las de Afiliado .4 Figure Corte DE CuchillasPlataforma la de inclinación la de Ajuste .3 Figura Corte DE Plataforma LA DE AjustesLA DE Correa LA DE Ajustes Corte de altura de Ajuste .2 FiguraCortacésped DEL Operación Chirrido un escuchar normal es desconectadoAlmacenamiento Y Mantenimiento Operación DE Consideraciones Giratorias CuchillasMáquina la Si .baja corte de plataforma la con Advertencia Seguridad DE Información Señalización de PalabraDescripción Símbolo ISO Símbolos General Información Instrucciones DE ReferenciaIlustrada partes de Lista Contenido DE TablaTema Página Tema 61A-SWMU 52A-SWMU21KAE-SWZU Operador EL Como Seguro TAN ES Cortacésped ¡SU RecuerdeManual DEL Operador No Parte 2003