Scag Power Equipment SWZU manual Neutral Adjustment, To Adjust the Custom-Cut Baffle height

Page 15

C.4" Position - baffle is installed using the bottom set of holes on the front baffle welded inside the cutter deck. (See Figure 8). Placing the baffle in the 4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".

To Adjust the Custom-Cut Baffle height:

1.Remove the hardware securing the Custom-Cut Baffle to the cutter deck (See Figure 5).

-NOTE-

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on the cutter deck size.

	MOUNTING	MOUNTING
	HARDWARE
		HARDWARE

2004 CCB

Figure 5. Custom-Cut Baffle

2.Move the Custom-Cut Baffle to desired position. (See Figures 6 through 8 for position).

3.Reinstall the mounting hardware as shown. (See Figures 6 though 8). Torque hardware to 39ft.lbs.

	TOP SET OF HOLES	CARRIAGE BOLT
	FOR 3" SETTING	CARRIAGE BOLT
	FOR 3" SETTING

2004 CCB - 3" Setting

ELASTIC STOP

NUT

Figure 6. 3" Custom-Cut Baffle Position

	MIDDLE SET OF HOLES	CARRIAGE BOLT
	FOR 3-1/2" SETTING	CARRIAGE BOLT
	FOR 3-1/2" SETTING

2004 CCB - 3-1/2" Setting

ELASTIC STOP

NUT

Figure 7. 3-1/2" Custom-Cut Baffle Position

	BOTTOM SET OF HOLES	CARRIAGE BOLT
	FOR 4" SETTING	CARRIAGE BOLT
	FOR 4" SETTING

2004 CCB - 4" Setting

ELASTIC STOP

NUT

Figure 8. 4" Custom-Cut Baffle Position

NEUTRAL ADJUSTMENT

-NOTE-

Neutral has been set by your Scag dealer at the time of setup and normally does not need to be adjusted. If, however, you find that neutral has come out of adjustment, follow the procedure below.

1.Raise the drive wheels off the ground and block the caster wheels to prevent the machine from moving.

2.Make sure the speed control lever is in neutral, the steering control levers are in the neutral latch position, and the parking brake is on. Start the engine.

3.Release the parking brake and note if the tires are rotating.

11

Image 15

Contents 2003 Model SwzuRemember Your Mower is only AS Safe AS the Operator Table of Contents 44-45 Illustrated Parts ListServicing the Engine and Drive Train Components General InformationIntroduction Direction ReferenceISO Symbols CE Mark Fast Slow Safety Information General Safety InformationBefore Operation Considerations Before Operation Considerations Contd Rotating BladesOperation Considerations Maintenance and Storage Use gasoline with an octane rating no less than Mower OperationCutter Deck Adjustments Cutter Deck Belt AdjustmentsCutter Deck Pitch Adjustments Custom-Cut Baffle AdjustmentCutter Blades To Adjust the Custom-Cut Baffle height Neutral AdjustmentSteering Control ROD Adjustment Tracking AdjustmentApply the parking brake Parking Brake Tracking AdjustmentLubrication & Maintenance Changing Hydraulic Oil Filter Element Hydraulic SystemChecking Hydraulic Oil Level Changing Hydraulic OilChanging Engine Crankcase Oil Engine Air CleanerChecking Electrolyte Level and Cleaning Battery Checking Engine Crankcase Oil LevelJump Starting Charging the BatteryCause Cure Troubleshooting Cutting ConditionsCondition Cause Cure Step Cut Scalping BladesHitting Dirt or Cutting Very Close to GroundDrive System Technical SpecificationsEngines Engine DeckAdditional Specifications Optional ITEMS/ATTACHMENTS Approximate Dimensions SWZU36A SWZU48A SWZU52A SWZU61ACutter Decks Page 36A Cutter Decks Ref. Part No. Number Description 48A, 52A & 61A Cutter Decks Part Description 36A Deck Frame 36A Deck Frame 48A and 52A Deck Frame Small Frame Ref. Part Description 48A and 52A Deck Frame *SMALL Frame52A & 61A Deck Frame Large Frame Part Description 52A 61A 52A & 61A Deck Frame *LARGE FrameEngine Deck Part Description Engine DeckDrive and Brake Components 15KA 17KA 21KAE 18KH 18HN Handle Assembly Small Frame Handle Assembly *SMALL Frame Handle Assembly Large Frame SWZU-21KAE Part Description Hydraulic Assembly Part Number Description Hydraulic AssemblyHydraulic Pump Assembly BDP-10L117 Hydraulic Pump Assembly Ground Kawasaki 15 HP & 17 HP Wire HarnessHandle Wire Harness Manual Start Kohler 18 HPHandle Wiring Harness Kawasaki Electric Start Part no Wire Harness Adapter Heavy-Duty Replacement Decals & InformationSwzu 15KA, 17KA & 18HN Swzu 18KH Swzu 21 KAE Limited Warranty Commercial Equipment Comercial Equipo Limitada Garantía Adicionales Especificaciones SWZU61A SWZU52A SWZU48A APROXIMADASSWZU36A DimensionesContinuación Técnicas Especificaciones Opcionales ARTÍCULOS/ACCESORIOSTransmisión DE Sistema Técnicas EspecificacionesSolución Causa Condición Corte DE Condiciones LAS EN Fallas DE IdentificaciónIrregular perfil o Corte de trayectoriaLa de ancho lo Inclinadas SalientesLa en cortar sin césped Corte de trayectoriasPasadas entre cortar sin césped De Franjas VetasPuente por Arranque Batería la de CargaCarga la durante producidos gases Las y chispas las arcos, los Mantenga .baterías Batería de limpiezaElectrolito de nivel del Verificación Baterías manipular de después manosHidráulico aceite de nivel el Verificar Aceite de filtro del elemento del CambioHidráulico Hidráulico aceite de CambioMantenimiento Y Lubricación Alineación de Ajuste .11 Figura PrecauciónCON DE Varilla LA DE Ajuste Neutral Ajuste .9 FiguraVelocidad de ajuste de palanca la Mueva Corte de deflector del 4 Posición .8 Figura Neutral AjusteCorte DE Cuchillas Cuchillas las de Afiliado .4 FigurePlataforma la de inclinación la de Ajuste .3 Figura Corte de altura de Ajuste .2 Figura CorteDE Plataforma LA DE Ajustes LA DE Correa LA DE AjustesChirrido un escuchar normal es desconectado Cortacésped DEL OperaciónAlmacenamiento Y Mantenimiento Giratorias Cuchillas Operación DE ConsideracionesMáquina la Si .baja corte de plataforma la con Advertencia Señalización de Palabra Seguridad DE InformaciónDescripción Símbolo ISO Símbolos Instrucciones DE Referencia General InformaciónContenido DE Tabla Ilustrada partes de ListaTema Página Tema Operador EL Como Seguro TAN ES Cortacésped ¡SU Recuerde 61A-SWMU52A-SWMU 21KAE-SWZUNo Parte 2003 Manual DEL Operador