Scag Power Equipment SWZU manual Parking Brake, Tracking Adjustment

Page 17

3.If the machine pulls to one side. Stop the mower by placing the steering control levers in the neutral position. Using the adjustment wrench located on the left side of the machine, turn the tracking adjustment nut on the slower side counter clockwise until the machine tracks straight. (See Figure 11)

4.Bring the steering control levers back to the neutral lock position and check to see that the machine does not creep forward on the adjusted wheel.

5.If the machine creeps in neutral you have moved out of the neutral band and will have to turn the tracking adjustment nut clockwise until the machine does not creep.

6.Repeat steps 1 and 2. If the machine continues to pull to one side, stop the mower by placing the steering control levers in the neutral position. Turn the tracking adjustment nut on the faster side clock- wise until the machine tracks straight.

7.If tracking cannot be achieved, contact your Scag servicing dealer.

PARKING BRAKE

1.Adjust the parking brake so that when the brake hand lever is against the stop on the handle bar, the brake levers on the brake shaft weldment are against the stops on the engine deck.

CAUTION:

Adjust the brake only enough to hold the machine. Excessive force may cause damage to the machine or brake components.

2.Adjust the brake actuator rod on either side of the machine to obtain proper brake adjustment.

Figure 11. Tracking Adjustment

13

Image 17

Contents 2003 Model SwzuRemember Your Mower is only AS Safe AS the Operator Table of Contents 44-45 Illustrated Parts ListIntroduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Before Operation Considerations Safety InformationGeneral Safety Information Before Operation Considerations Contd Rotating BladesOperation Considerations Maintenance and Storage Use gasoline with an octane rating no less than Mower OperationCutter Deck Adjustments Cutter Deck Belt Adjustments Cutter Blades Cutter Deck Pitch Adjustments Custom-Cut Baffle Adjustment To Adjust the Custom-Cut Baffle height Neutral AdjustmentApply the parking brake Steering Control ROD AdjustmentTracking Adjustment Parking Brake Tracking AdjustmentLubrication & Maintenance Checking Hydraulic Oil Level Hydraulic SystemChanging Hydraulic Oil Changing Hydraulic Oil Filter ElementChecking Electrolyte Level and Cleaning Battery Engine Air CleanerChecking Engine Crankcase Oil Level Changing Engine Crankcase OilJump Starting Charging the BatteryCause Cure Troubleshooting Cutting ConditionsCondition Cause Cure Hitting Dirt or Cutting Very Close to Scalping BladesGround Step CutEngines Technical SpecificationsEngine Deck Drive SystemCutter Decks Additional Specifications Optional ITEMS/ATTACHMENTSApproximate Dimensions SWZU36A SWZU48A SWZU52A SWZU61A Page 36A Cutter Decks Ref. Part No. Number Description 48A, 52A & 61A Cutter Decks Part Description 36A Deck Frame 36A Deck Frame 48A and 52A Deck Frame Small Frame Ref. Part Description 48A and 52A Deck Frame *SMALL Frame52A & 61A Deck Frame Large Frame Part Description 52A 61A 52A & 61A Deck Frame *LARGE FrameEngine Deck Part Description Engine DeckDrive and Brake Components 15KA 17KA 21KAE 18KH 18HN Handle Assembly Small Frame Handle Assembly *SMALL Frame Handle Assembly Large Frame SWZU-21KAE Part Description Hydraulic Assembly Part Number Description Hydraulic AssemblyHydraulic Pump Assembly BDP-10L117 Hydraulic Pump Assembly Handle Wire Harness Manual Start Wire HarnessKohler 18 HP Ground Kawasaki 15 HP & 17 HPHandle Wiring Harness Kawasaki Electric Start Part no Wire Harness Adapter Heavy-Duty Replacement Decals & InformationSwzu 15KA, 17KA & 18HN Swzu 18KH Swzu 21 KAE Limited Warranty Commercial Equipment Comercial Equipo Limitada Garantía Continuación Técnicas Especificaciones SWZU61A SWZU52A SWZU48A APROXIMADASSWZU36A DimensionesOpcionales ARTÍCULOS/ACCESORIOS Adicionales EspecificacionesTransmisión DE Sistema Técnicas EspecificacionesSolución Causa Condición Corte DE Condiciones LAS EN Fallas DE IdentificaciónLa de ancho lo Corte de trayectoriaInclinadas Salientes Irregular perfil oPasadas entre cortar sin césped Corte de trayectoriasDe Franjas Vetas La en cortar sin céspedCarga la durante producidos gases Puente por ArranqueBatería la de Carga Electrolito de nivel del Verificación Batería de limpiezaBaterías manipular de después manos Las y chispas las arcos, los Mantenga .bateríasHidráulico Aceite de filtro del elemento del CambioHidráulico aceite de Cambio Hidráulico aceite de nivel el VerificarMantenimiento Y Lubricación Alineación de Ajuste .11 Figura PrecauciónVelocidad de ajuste de palanca la Mueva CON DE Varilla LA DE AjusteNeutral Ajuste .9 Figura Corte de deflector del 4 Posición .8 Figura Neutral AjustePlataforma la de inclinación la de Ajuste .3 Figura Corte DE CuchillasCuchillas las de Afiliado .4 Figure DE Plataforma LA DE Ajustes CorteLA DE Correa LA DE Ajustes Corte de altura de Ajuste .2 FiguraChirrido un escuchar normal es desconectado Cortacésped DEL OperaciónAlmacenamiento Y Mantenimiento Máquina la Si .baja corte de plataforma la con Giratorias CuchillasOperación DE Consideraciones Advertencia Señalización de Palabra Seguridad DE InformaciónDescripción Símbolo ISO Símbolos Instrucciones DE Referencia General InformaciónTema Contenido DE TablaIlustrada partes de Lista Página Tema 52A-SWMU 61A-SWMU21KAE-SWZU Operador EL Como Seguro TAN ES Cortacésped ¡SU RecuerdeNo Parte 2003 Manual DEL Operador