Scag Power Equipment STC48V-26BS, STC52V-23BV, STC61V-23BV General Information, Introduction

Page 5

Section 1

GENERAL INFORMATION

1.1 INTRODUCTION

Your mower was built to the highest standards in the industry. However, the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual.

If additional information or service is needed, contact your Scag Power Equipment Dealer.

We encourage you to contact your dealer for repairs. All Scag dealers are informed of the latest methods to service this equipment and provide prompt and efficient service in the field or at their service shop. They carry a full line of Scag service parts.

THE REPLACEMENT OF ANY PART ON THIS PRODUCT BY OTHER THAN THE MANUFACTURER'SAUTHORIZED REPLACEMENTPARTMAYADVERSELY AFFECTTHEPERFORMANCE,DURABILITYOR SAFETY OF THIS PRODUCT.

USE OF OTHER THAN ORIGINAL SCAG REPLACEMENT PARTS WILL VOID THE WARRANTY.

When ordering parts, always give the model and serial number of your mower. The serial number plate is located under the seat as shown in Figure 1-1.

SERIAL NUMBER

PLATE LOCATION

SCAG

Power Equipment

Model

Serial

STC 2001 SPL-1

Scag approved attachments and accessories: GC-STC-V, GC-STWC-61V (p/n 9057, p/n 9058) GC-STC-CSV, GC-STWC-CS61V (p/n 9061, p/n 9062) Mulch Plate (p/n 9286, 9287, 9288)

Hurricane Mulch (p/n 9283, 9284, 9285) STC Hitch (p/n 9241)

STC - Lights (p/n 9274)

Tiger Striper (p/n 9269) GC-4D (p/n 9054) GC-F4 (p/n 9055)

Soft Ride Seat (p/n 9291)

Suspension Seat (p/n/ 9292) Blade Buddy (p/n 9212)

WARNING:

For pictorial clarity, some illustrations and figures in this manual may show shields, guards or plates open or removed. Under no circumstances should your mower be operated without these devices in place.

All information is based upon product information available at the time of approval for printing. Scag Power Equipment reserves the right to make changes at any time without notice and without incurring any obligation.

1.2 DIRECTION REFERENCE

The “Right” and “Left”, “Front” and “Rear” of the machine are referenced from the operator’s right and left when seated in the normal operating position and facing the forward travel direction.

1.3SERVICING THE ENGINE AND DRIVE TRAIN COMPONENTS

Figure 1-1 Mower Serial Number Plate Location

USE ONLY SCAG APPROVED ATTACHMENTS AND ACCESSORIES.

Attachments and accessories manufactured by companies other than Scag Power Equipment are not approved for use on this machine.

The detail servicing and repair of the engine, hydraulic pumps and gearboxes are not covered in this manual; only routine maintenance and general service instructions are provided. For service of these components during the limited warranty period, it is important to contact your Scag dealer or find a local authorized servicing agent of the component manufacturer. Any unauthorized work done on these components during the warranty period may void your warranty.

1

Image 5
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Introduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsFalling Hazard Thrown Object Hazard Parking Brake Spinning BladeOn/Start Spring Tension on Idler Off/Stop Fast Slow Before Operation Considerations Safety InformationSignal Words Operation Considerations Know the function of all controls and how to stop quicklyOperation Considerations Contd Seat Belt Inspection ROLL-OVER Protection SystemMaintenance Considerations & Storage Safety and Instructional Decals Engine SpecificationsElectrical TractorCutter Deck Tractor ContdHydraulic System ProductivityControls and Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemForward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Check the tire pressure. Adjust pressure if necessaryHillside Operation Removing Clogged Material Adjusting Cutting HeightMoving Mower with Engine Stopped Recommendations for MowingDeck Release Lever Towing optional hitch accessoryCondition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Contd Condition Cause Cure Ground Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsThrottle Control and Choke Adjustments Tracking AdjustmentBelt Adjustment Belt AlignmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Cutter Deck Height Custom-Cut Baffle AdjustmentCustom-Cut Baffle Maintenance Chart Recommended Service Intervals MaintenanceBreak-In 100 200 500 Procedure Comments First HoursLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdProcedure Comments Break-In 100 200 500 First Shell Alvania #2 found at Shell Service StationsLubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelChanging Engine Oil Filter Changing Hydraulic Oil Filter ElementEngine OIL Checking Engine Crankcase Oil LevelCleaning and/or Replacing Air Cleaner Element Engine AIR CleanerEngine Fuel System Filling the Fuel TankCharging the Battery BatteryBattery Electrolyte First AID Jump StartingDrive Belts Blade ReplacementCutter Blades Blade InspectionBODY, DECK, and Upholstery Tires25 PSI 12 PSISection 52A 48V& 52V Cutter Decks 61V Cutter Deck 61V Cutter Deck Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Sheet Metal Components STC Fixed ROLL-OVER Protection System Ref. Part No. No. Description Drive System Components Drive System Components Engine and Attaching Parts Briggs & Stratton Part Description 33A 29, 29A Steering Components Brake Components Brake Components Fuel and Hydraulic System Ref. Part Description Electrical System Part Description Hydraulic Pump Assembly Housing Kit Commercial 482166R STC 2006 RDP2 Electrical Schematic Briggs & Stratton Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Motrices Ruedas Tapicería Y Plataforma CuerpoLocas Ruedas Cada de después llantas las de presiones las VerifiqueCuchillas las de Afiliado .B Cuchilla la de Reemplazo .CPara apropiada protección la lleve Siempre Cuchillas las de Afiliado 8-7 FiguraBatería la de Carga .A Puente por Arranque .BAdvertencia Batería Batería DE Electrolito Para Auxilios PrimerosCombustible de tanque del Llenado .A Aire de filtro Del elemento del reemplazo y/o Limpieza .AMotor DEL Motor DEL Aire DE FiltroHidráulico aceite de Filtro del elemento del Cambio .C Motor del aceite de filtro de Cambio .CCárter del aceite de Cambio .B Cárter del aceite de nivel del Verificación .AHidráulico Sistema Hidráulico aceite de Cambio .BHidráulico aceite de nivel el Verificar .A Conexión de puntos de Lubricación 1.7 Figura Accesorios DE Lubricación DE Tabla Lubricación Figura LA VEARecomendados Servicio DE Intervalos Mantenimiento DE Tabla MantenimientoPersonalizado corte de Deflector .8-6 Figura Personalizado corte deCorte de plataforma la de Altura Personalizado corte de deflector del AjusteCorte de plataforma la de Tope .7-6 Figura Plataforma la deCorte de plataforma la de Inclinación Corte de plataforma la de NivelCorte de plataforma la de Ajuste .4-6 Figura Corte DE Plataforma LA DE AjusteCorrea LA DE Ajuste Correa LA DE AlineaciónEstrangulación DE Ajuste Y Aceleración DE Control Alineación de AjusteDirección de control de varillas de Ajuste .3-6 Figura Neutral AjusteDesplazamiento DE Ajustes Estacionamiento DE Freno DEL Ajuste AjusteFreno de varilla la de Ajuste .2-6 Figura Freno de Ajuste .1-6 FiguraSolución Causa Condición Solución Causa Condición Continuación Fallas DE Solución Pasadas entre cortar sin césped Corte de trayectoriasDe Franjas Vetas En cortar sin céspedCorte de altura de Ajuste 5-4 Figura Opcional enganche de accesorio RemolquePlataforma Equipo del peso ElDetenido Motor EL CON Césped ELOperación LA DE Después CortacéspedesDEL Estacionamiento Cuesta UNA EN OperaciónCortador del Reversa en DesplazamientoAccionamiento de Interruptor 3-4 Figura Corte DE Cuchillas Plataforma DE Transmisión LA DE ConexiónDirección Terreno EL EN Desplazamiento Adelante hacia DesplazamientoHoras 20 aproximadamente Uso de día Primer Inicial Motor EL ArrancarDescarga de válvula de Control 2-4 Figura Seguridad DE Bloqueo DE SistemaIdentificación Instrumentos E Controles Operación DE InstruccionesInstrumentos e Controles 1-4 Figura Frío motor un arrancar para Usado .1-4 FiguraContinuación Tractor ProductividadCorte DE Plataforma Tractor EspecificacionesEléctrico Sistema MotorSeguridad DE Y Instructivas Calcomanías Reversa AdelanteAlmacenamiento Y Mantenimiento DE Consideraciones Contra Protección DE Sistema STC VuelcoOperación DE Consideraciones ContinuaciónOsha POR Aprobadas Raciones Inglés leer puede no mecánico o operador el SiSeñalización DE Palabra Seguridad DEIntroducción 1.2 Información Operación LA a Previas ConsideracionesDescripción Símbolo ISO Símbolos CE la de MarcaIntroducción General InformaciónInstrucciones DE Referencia Página Tema Continuación Contenido DE TablaAjustes 6 Sección Operación de Instrucciones 4 Sección Contenido DE TablaEspecificaciones 3 Sección Seguridad de Información 2 SecciónAdvertencia Manual