Scag Power Equipment STC52V-27CV-SS manual Custom-Cut Baffle Adjustment

Page 30

R

Section 6

3.Check the cutter deck cutting height by placing the lanyard pin in the 3" position on the cutting height index. Release the deck from the transport position and allow the deck to move to the 3" cutting height position.

4.Check the measurement from the floor to the cutter blade tip. If the measurement is not at 3", an adjustment can be made using the deck height control rod. See Figure 6-6.

- NOTE -

If an adjustment had to be made, be sure that the cutter deck can easily be locked into the transport position.

6.7 Custom-Cut Baffle Adjustment

The Custom-Cut Baffle is designed to deliver optimum airflow and superior cutting performance in any type of grass. The Custom-Cut Baffle can be raised or lowered to precisely tailor the deck's performance for the type of grass being cut.The baffle can be set in seven (7) different positions for optimum performance.

A.3-1/2" or 3-3/4" Position - (See Figure 6-9). For very tall, wiry or tough-to-cut grass.

B.4" (factory setting), 4-1/4" or 4-1/2" Position - (See Figure 6-9). For general purpose cutting.This gives the best mix of cutting performance in all types of grass.

C.4-3/4" or 5-1/4" Position - (See Figure 6-9). Placing the baffle in either the 4-3/4" or 5-1/4" setting will enhance fall cutting (leaf pickup) and reduce cutter deck "blowout".

To adjust the Custom-Cut Baffle height:

1.Place the cutter deck in the transport position.

2.Remove the hardware securing the Custom-Cut Baffle to the cutter deck.

- NOTE -

Hardware location used in the illustrations are for reference only. Location of hardware may vary depending on cutter deck size.

3.Move the Custom-Cut Baffle to desired position. See Figure 6-9.

4.Reinstall the mounting hardware. Torque hardware to 39 ft-lbs.

1 2 3 4

1 2

A

3 4

B

 

A

B

Custom-Cut Baffle Adjustment

 

 

Mounting Slot Selected

 

Mounting Hardware Location

Slot “A”

Hole 1

Hole 2

Hole 3

Hole 4

Height (inches)

3-3/4”

4-1/4”

4-3/4”

5-1/4”

Slot “B”

 

Hole 2

Hole 3

Hole 4

Height (inches)

 

3-1/2”

4”

4-1/2”

Figure 6-9. 7-Position Custom-Cut Baffle Adjustment

26

Image 30
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator STC48V-19KAISTC52V-27CV-SS Table of Contents Limited Warranty Commercial Equipment Following SectionIntroduction USE only Scag Approved Attachments and AccessoriesGeneral Information Direction ReferenceSymbols Symbol DescriptionSTT Models This symbol means Attention! Become Alert! Your Safety InformationSignal Words Signal WordOperation Considerations Section Roll-over protection system Foldable Roll-Over Protection SystemSeat Belt Inspection Maintenance Considerations & storage Using a spark arrestorSafety and Instructional Decals Install Belt COvER BeforeEngine ElectricalTractor Hydraulic System Weights and Dimensions 48V 52V 61VCutter Deck ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Initial RUN-IN ProceduresFirst Day of Use or Approximately 20 Hours Starting the Engine Ground Travel and SteeringForward Travel Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Rotating BladesHillside Operation After OperationAdjusting Cutting Height Moving Mower with Engine StoppedRecommendations for Mowing Towing optional hitch accessory Deck Release LeverTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Cutting Conditions Contd Step Cut Ridge in Center Scalping Blades HittingDirt or CuttingVery Close To the Ground Cutting pathAdjustments Parking Brake AdjustmentTravel Adjustments Neutral Adjustment Tracking AdjustmentCutter Deck Adjustments Throttle Control and Choke AdjustmentsBelt Adjustment Belt AlignmentCutter Deck Height Adjustment Cutter Deck Pitch Cutter Deck HeightCustom-Cut Baffle Adjustment Position Custom-Cut Baffle AdjustmentElectric clutch adjustment Clutch Air Gap AdjustmentProcedure Comments Break-In 100 200 500 First MaintenanceMaintenance Chart Recommended Service Intervals HoursLubrication Location Lubrication Interval Lubricant NO. PlacesLubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine Oil Engine Fuel SystemEngine Air Cleaner Cleaning and/or Replacing Air Cleaner ElementReplacing In-Line Fuel Filter Elements Battery Electrolyte First AID BatteryCharging the Battery Jump StartingCutter Blades Blade ReplacementDrive Belts Blade InspectionTires BODY, DECK, and UpholsteryIllustrated Parts List Scag Approved Attachments and Accessories48V & 52V Cutter Decks Description 61V Cutter Deck 424367 Dust Shield 483210 Idler Pulley, 5 Dia Cutter Deck Controls Cutter Deck Controls Sheet Metal Components 482619 Tire, 13 x 6.5-6 Smooth 483736 STC Foldable ROLL-OVER Protection System STC Foldable ROLL-OVER Protection System STC Suspension Seat Section Drive System Components 04019-04 Nut, Serr. Flange 3/8-16 04001-136 Engine & Attaching Parts Section Steering Components Damper orange colored print Damper blue colored print Brake Components Brake Components Wheel Motor Part Number Identification HYDRO-GEAR ParkerSection 33 47 Fuel and Hydraulic System Electrical System Battery, 350CCA Not Available Through Scag BDP-10A Hydraulic Pump Assembly Housing Kit Replacement Decals and Information Plates Manufactured Under ONE or More482166R STC 2009 RDP2 Electrical Schematic PTO Switch Diode KEYLimited Warranty Commercial Equipment Garantía Limitada Equipo Comercial RecauciónP Está mientras equipo del parte ninguna lave NoNota CuchillaNota Cuchilla la de Reemplazo .8-7 Figura Corte de cuchillas con trabajar al ojos yTransmisión DE Correas Afilado.BRranB Bater DE 7aterBater Deaíla Electrolito Para Auxilios PrimerosMotor Aire del Iltro7 Istema5.7del MotorCombustiblede Motor Ceite7Aceite De nivel Hidrulicoá ErificarV.A Hidrulicoá S istema3.7Aceite hidrulicoCáambio.B Hidráulico aceite de Depósito .2-7 FiguraConexión de puntos de Lubricación .1-7 Figura Observaciones Procedimiento Ubicaciones Lubricante Lubricación UbicaciónDE Intervalo HorasObservaciones Procedimiento Primeros Inicial USO Horas Sección Personalizado a 7juste.6ctorl Corte de plataforma la de Tope .7-6 FiguraCorte de plataforma la de nivel del Ajuste .5-6 Figura Corte de plataforma la de altura de Ajuste .6-6 FiguraAdvertencia Dirección de Control de varilla la de Ajuste .3-6 FiguraAjustes Solución Causa Condición Coninuaciónt ID E Enganche cional Remolque14.4orio Corte DE Altura LA DE Ajuste Descarga de válvula de Control .4-4 FigurePeligro RecauciónP Precaución Inicial Arranque DE Procedimientos Descarga de válvula de Control .2-4 FigureInstrumentos e Controles .1-4 Figure Interruptor El .1-4 Figura encendido de Interruptor61V 52V 48V PRO Especificaciones SE DE Yuridadas G Instructi CALCOMANÍAS.27 Ertenciaadv Ertenciaad Almacenamiento mantenimientoSeguridad de cinturón del Inspección .3-2 Figura Rops del Bisagra .2-2 FiguraVuelco contra protección de Sistema .1-2 Figura Uelcov ProteccióndeOsha POR Aprobadas Operaciones LAS CONDiferente posición una en dirección de control Defectuosamente Funcionando ni desconectado bloqueo deNo estacionamiento de freno el y neutral la de De freno el desconectada, esté plataforma deSeñalización DE Palabras SE DEInformación RidadgSTT Descripción SímboloINTRODUCCIÓN11 General InformaciónInstrucciones DE REFERENCIA12 Scag POR Aprobados Dispositivos USE SóloGarant StaliManten Ridad Advertencia Operador DEL Manual