Scag Power Equipment STC Operation Considerations Contd, Roll Over Protection System Optional

Page 10

Section 2

2.4OPERATION CONSIDERATIONS (CONT'D)

3.To prevent tipping or loss of control, start and stop smoothly, avoid unnecessary turns and travel at reduced speed.

4.When using any attachment, never direct the discharge of material toward bystanders or allow anyone near the machine while in operation.

5.Before attempting to start the engine, with the operator in the seat, disengage power to the cutter deck, place the steering control levers in the neutral position and engage the parking brake.

6.If the mower discharge ever plugs, shut off the engine, remove the ignition key, and wait for all movement to stop before removing the obstruction.

WARNING:

Do not use your hand to dislodge the clogged discharge chute. Use a stick or other device to remove clogged material.

7.Be alert for holes, rocks, roots and other hidden hazards in the terrain. Keep away from any dropoff. Beware of overhead obstructions (low limbs, etc.), underground obstacles (sprinklers, pipes, tree roots, etc.). Cautiously enter a new area. Be alert for hidden hazards.

8.Disengage power to cutter deck before backing up. Do not mow in reverse unless absolutely necessary and then only after observation of the entire area behind the mower.

9.DO NOT turn sharply. Use care when backing up.

10.Disengage power to cutter deck before crossing roads, walks or gravel drives.

11.Mow only in daylight or good artificial light.

12.Take all possible precautions when leaving the machine unattended, such as disengaging the mower, lowering

the attachments, setting the parking brake, stopping the engine, and removing the key.

13.Disengage power to the attachments when transporting or when not in use.

14.The machine and attachments should be stopped and inspected for damage after striking a foreign object, and damage should be repaired before restarting and operating the machine.

CAUTION:

DO NOT touch the engine or the muffler while the engine is running or immediately after stopping. These areas may be hot enough to cause a burn.

WARNING:

DO NOT run the engine inside a building or a confined area without proper ventilation. Exhaust fumes are hazardous and could cause death.

2.5ROLL OVER PROTECTION SYSTEM (OPTIONAL)

This mower has been designed for good traction and stability under normal mowing conditions. However, caution must be used when traveling on slopes, especially when the grass is wet. Wet grass reduces traction and steering control.

An optional Roll Over Protection System is available for this machine (see authorized dealer for details) and should be installed if the machine is to be operated on slopes or inclines to insure operator safety.

After initial installation by authorized dealer, any or all parts of the Roll Over Protection System MUST NOT be removed. Failure to adhere to this guideline could result in injury or death.

ROP's Operating Instructions.

1.Securely fasten seat belt during operation of the machine.

6

Image 10
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Direction Reference General InformationIntroduction Servicing the Engine and Drive Train ComponentsISO Symbols CE Mark Fast Slow Signal Word Safety InformationSignal Words Before Operation ConsiderationsBefore Operation Considerations Contd Operation ConsiderationsOperation Considerations Contd Roll Over Protection System OptionalMaintenance Considerations Safety and Instructional Decals Electrical SpecificationsEngine TractorHydraulic System Tractor ContdCutter Deck ProductivityOperating Instructions Controls and Instrument IdentificationSafety Interlock System Dump Valve ControlGround Travel and Steering Starting the EngineForward Travel Reverse Travel Engaging the Deck Drive Cutter BladesRemoving Clogged Material Hillside OperationAfter Operation Parking the MowerMoving Mower with Engine Stopped Adjusting Cutting HeightRecommendations for Mowing Towing Optional Hitch Accessory Adjusting Cutting HeightTroubleshooting Cutting Conditions Condition Cause CureTroubleshooting Contd Condition Cause Cure Ground Adjustments Parking Brake AdjustmentTravel Adjustments Neutral AdjustmentBelt Adjustment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AlignmentCutter Deck Level Cutter Deck AdjustmentsCutter Deck Pitch Custom-Cut Baffle Adjustment Cutter Deck HeightCustom-Cut Baffle Break-In 100 200 500 Procedure Comments First MaintenanceMaintenance Chart Recommended Service Intervals HoursLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdProcedure Comments Break-In 100 200 500 First Lubrication Fitting Points Checking Hydraulic Oil Level Changing Hydraulic OilEngine OIL Engine Fuel SystemBattery Engine AIR CleanerCleaning and/or Replacing Air Cleaner Element Replacing In-Line Fuel Filter ElementBattery Electrolyte First AID Charging the BatteryJump Starting Cutter Blades Blade ReplacementDrive Belts Blade InspectionTires BODY, DECK, and Upholstery48A& 52A Cutter Decks Part Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Sheet Metal Components Drive System Components Ref. Part No. No. Description Engine and Attaching Parts Kawasaki & Kohler Part Description 19KA 20CV 21KA 23KA Engine and Attaching Parts Honda Engine Oil Filter P/N 33A 29, 29A Steering Components Brake Components Brake Components Fuel and Hydraulic System Ref. Part Description Electrical System Part Description Hydraulic Pump Assembly Housing Kit Commercial 482166R STC 2003 RDP2 Electrical Schematic KAWASAKI, Kohler & Honda Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Comprimido Aire use motor el lave No .caliente está LlantasCuchilla la de Reemplazo 10-7 Figura Mientras equipo del parte ninguna lave NoCuchilla la de Reemplazo .C Cuchillas las de Afiliado .BPara apropiada protección la lleve Siempre Cuchilla la de Afilado 9-7 FiguraBatería la de Carga .A Puente por Arranque .BBatería DE Electrolito Para Auxilios Primeros Línea en combustible BateríaAire de filtro Motor DEL Aire DE FiltroMotor DEL Combustible DE Sistema Combustible de tanque del Llenado .AMotor DEL Aceite Hidráulico aceite de nivel el Verificar .A Hidráulico aceite de Cambio .BHidráulico Sistema Lubricación DE Grasa DE Conexiones Accesorios DE Lubricación DE Tabla Lubricación Observaciones Procedimiento 500 200 100Observaciones Procedimiento 500 200 100 Inicial Uso MantenimientoRecomendados Servicio DE Intervalos Mantenimiento DE Tabla HorasPersonalizado Corte de plataforma la de Altura Posiciones 3 tres en colocar puede se deflector ElCorte de plataforma la de Nivel Corte DE Plataforma LA DE AjustesEstrangulación Y Aceleración DE Controles LOS DE Ajustes Correa LA DE AjusteCorrea LA DE Alineación Desplazamiento DE Ajustes Neutral AjusteDirección de control de varillas de Ajuste .3-6 Figura Freno de varilla la de Ajuste .2-6 Figura AjustesEstacionamiento DE Freno DEL Ajuste Freno de Ajuste .1-6 FiguraSolución Causa Condición Solución Causa Condición Continuación Fallas DE Solución De Franjas Vetas Corte de trayectoriasEntre cortar sin césped La en cortar sin céspedOpcional Enganche DE Accesorio Remolque Plataforma la de liberación de Palanca 4-4 Figura Corte DE Altura LA DE AjusteCésped EL Cortar Para Recomendaciones Detenido Motor EL CON Cortacésped DEL DesplazamientoOperación LA DE Después Atascado Material DEL RetiroCortacésped DEL EstacionamientoCorte DE Cuchillas Plataforma DE Transmisión LA DE Conexión Reversa en DesplazamientoHoras 10 aproximadamente Uso de día Primer Inicial Motor DEL ArranqueArranque DE Procedimientos Seguridad DE Bloqueo DE Sistema De fusibles Dos 1-4 Figura PortafusiblesOperación DE Instrucciones Instrumentos E Controles DE IdentificaciónCorte DE Plataforma ProductividadContinuación Tractor Eléctrico Sistema EspecificacionesTractor MotorSeguridad DE Y Instructivas Calcomanías Mantenimiento DE Consideraciones Opcional Vuelco Contra Protección DE Sistema ContinuaciónOperación DE Consideraciones Continuación Operación LA a Previas Consideraciones El opere Nunca .accionado no estacionamientoSeñalización de Palabra Seguridad DE InformaciónOperación Señalización DE PalabrasDescripción Símbolo ISO Símbolos Instrucciones DE Referencia General InformaciónIntroducción Mantenimiento 7 Sección Continuación Contenido DE TablaRepuesto de Piezas 8 Sección Ajustes 6 SecciónContenido DE Tabla General Información 1 SecciónAdvertencia Manual