Scag Power Equipment STC operating instructions Maintenance Considerations

Page 11

2.Whenever possible, avoid operating the machine near ditches, embankments and steep inclines.

3.Reduce speed when turning, operating on slopes, slick or wet surfaces. Allow extra distance to stop.

4.Stay off of slopes too steep for safe operation. To check a slope, attempt to back up it (with the cutter deck down). If the machine cannot back up the slope without the wheels slipping, do not operate the machine on this slope.

5.Always travel up or down the slope whenever possible. Never across the slope.

6.Operate the machine smoothly, no sudden turns, starts or stops on a slope.

7.Never tow on slopes. The weight of the towed equipment may cause loss of traction and loss of control.

8.DO NOT permit untrained personnel to operate the machine.

2.6 MAINTENANCE CONSIDERATIONS

1.Never make adjustments to the machine with the engine running unless specifically instructed to do so. If the engine is running, keep hands, feet, and clothing away from moving parts.

2.Remove the key from the ignition switch to prevent accidental starting of the engine when servicing or adjusting the machine.

3.Keep all nuts, bolts and screws tight, to ensure the machine is in safe working condition. Check blade mounting bolts frequently to be sure they are tight.

4.Do not change the engine governor settings or overspeed the engine. See the engine operator's manual for information on engine settings.

5.To reduce fire hazard, keep the engine free of grass, leaves, excessive grease, oil and dirt.

CAUTION:

Hydraulic fluid is under high pressure. Keep body and hands away from pinholes or nozzles that eject hydraulic fluid under high pressure. Hydraulic fluid under high pressure may have sufficient force to penetrate skin and cause serious injury. If hydraulic fluid is injected into the skin, it must be surgically removed within a few hours by a doctor or gangrene may result. If you need service on your hydraulic system, please see your authorized Scag dealer.

7

Image 11

Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Servicing the Engine and Drive Train Components General InformationIntroduction Direction ReferenceISO Symbols CE Mark Fast Slow Before Operation Considerations Safety Information Signal Words Signal WordOperation Considerations Before Operation Considerations ContdRoll Over Protection System Optional Operation Considerations ContdMaintenance Considerations Safety and Instructional Decals Tractor SpecificationsEngine ElectricalProductivity Tractor ContdCutter Deck Hydraulic SystemControls and Instrument Identification Operating InstructionsDump Valve Control Safety Interlock SystemForward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse TravelParking the Mower Hillside OperationAfter Operation Removing Clogged MaterialRecommendations for Mowing Adjusting Cutting HeightMoving Mower with Engine Stopped Adjusting Cutting Height Towing Optional Hitch AccessoryCondition Cause Cure Troubleshooting Cutting ConditionsTroubleshooting Contd Condition Cause Cure Ground Parking Brake Adjustment AdjustmentsNeutral Adjustment Travel AdjustmentsBelt Alignment Tracking AdjustmentThrottle Control and Choke Adjustments Belt AdjustmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Cutter Deck Height Custom-Cut Baffle AdjustmentCustom-Cut Baffle Hours MaintenanceMaintenance Chart Recommended Service Intervals Break-In 100 200 500 Procedure Comments FirstProcedure Comments Break-In 100 200 500 First Maintenance Chart Recommended Service Intervals ContdLubrication Grease Fitting Lubrication Chart see Figure Lubrication Fitting Points Changing Hydraulic Oil Checking Hydraulic Oil LevelEngine Fuel System Engine OILReplacing In-Line Fuel Filter Element Engine AIR CleanerCleaning and/or Replacing Air Cleaner Element BatteryJump Starting Charging the BatteryBattery Electrolyte First AID Blade Inspection Blade ReplacementDrive Belts Cutter BladesBODY, DECK, and Upholstery Tires48A& 52A Cutter Decks Part Description Cutter Deck Controls Cutter Deck Controls Sheet Metal Components Sheet Metal Components Drive System Components Ref. Part No. No. Description Engine and Attaching Parts Kawasaki & Kohler Part Description 19KA 20CV 21KA 23KA Engine and Attaching Parts Honda Engine Oil Filter P/N 33A 29, 29A Steering Components Brake Components Brake Components Fuel and Hydraulic System Ref. Part Description Electrical System Part Description Hydraulic Pump Assembly Housing Kit Commercial 482166R STC 2003 RDP2 Electrical Schematic KAWASAKI, Kohler & Honda Limited Warranty Commercial Equipment Garantía Limitada Equipo Comercial Mientras equipo del parte ninguna lave No LlantasCuchilla la de Reemplazo 10-7 Figura Comprimido Aire use motor el lave No .caliente estáCuchilla la de Afilado 9-7 Figura Cuchillas las de Afiliado .BPara apropiada protección la lleve Siempre Cuchilla la de Reemplazo .CBatería DE Electrolito Para Auxilios Primeros Puente por Arranque .BBatería la de Carga .A Motor DEL Aire DE Filtro BateríaAire de filtro Línea en combustibleMotor DEL Aceite Combustible de tanque del Llenado .AMotor DEL Combustible DE Sistema Hidráulico Sistema Hidráulico aceite de Cambio .BHidráulico aceite de nivel el Verificar .A Lubricación DE Grasa DE Conexiones Observaciones Procedimiento 500 200 100 Accesorios DE Lubricación DE Tabla LubricaciónHoras MantenimientoRecomendados Servicio DE Intervalos Mantenimiento DE Tabla Observaciones Procedimiento 500 200 100 Inicial UsoPersonalizado Posiciones 3 tres en colocar puede se deflector El Corte de plataforma la de AlturaCorte DE Plataforma LA DE Ajustes Corte de plataforma la de NivelCorrea LA DE Alineación Correa LA DE AjusteEstrangulación Y Aceleración DE Controles LOS DE Ajustes Dirección de control de varillas de Ajuste .3-6 Figura Neutral AjusteDesplazamiento DE Ajustes Freno de Ajuste .1-6 Figura AjustesEstacionamiento DE Freno DEL Ajuste Freno de varilla la de Ajuste .2-6 FiguraSolución Causa Condición Solución Causa Condición Continuación Fallas DE Solución La en cortar sin césped Corte de trayectoriasEntre cortar sin césped De Franjas VetasOpcional Enganche DE Accesorio Remolque Detenido Motor EL CON Cortacésped DEL Desplazamiento Corte DE Altura LA DE AjusteCésped EL Cortar Para Recomendaciones Plataforma la de liberación de Palanca 4-4 FiguraDEL Estacionamiento Atascado Material DEL RetiroCortacésped Operación LA DE DespuésReversa en Desplazamiento Corte DE Cuchillas Plataforma DE Transmisión LA DE ConexiónArranque DE Procedimientos Motor DEL ArranqueHoras 10 aproximadamente Uso de día Primer Inicial De fusibles Dos 1-4 Figura Portafusibles Seguridad DE Bloqueo DE SistemaInstrumentos E Controles DE Identificación Operación DE InstruccionesContinuación Tractor ProductividadCorte DE Plataforma Motor EspecificacionesTractor Eléctrico SistemaSeguridad DE Y Instructivas Calcomanías Mantenimiento DE Consideraciones Operación DE Consideraciones ContinuaciónOpcional Vuelco Contra Protección DE Sistema El opere Nunca .accionado no estacionamiento Continuación Operación LA a Previas ConsideracionesSeñalización DE Palabras Seguridad DE InformaciónOperación Señalización de PalabraDescripción Símbolo ISO Símbolos Introducción General InformaciónInstrucciones DE Referencia Ajustes 6 Sección Continuación Contenido DE TablaRepuesto de Piezas 8 Sección Mantenimiento 7 SecciónGeneral Información 1 Sección Contenido DE TablaAdvertencia Manual