Remington ST3812B, ST4514B Important Safety Information, Servicing of Double-Insulated Tools

Page 6

2 Chapter 1: Important Safety Information

10.Provide Ground Fault Circuit Inter- rupter (GFCI) protection on the circuit or outlet to be used for trim- mer/edger. You may use receptacles with built-in GFCI protection for this safety measure.

WHILE OPERATING

TRIMMER/EDGER

1.Stay alert. Watch what you are doing. Use common sense.

2.Be aware of extension cord while operat- ing trimmer/edger.Be careful not to trip over extension cord.

3.Avoid unintentional starting. Do not carry plugged-in trimmer/edger with finger on switch. Be sure switch is OFF when plugging in trimmer/ edger.

4.Do not overreach. Keep proper foot- ing and balance at all times when operating trimmer/edger.

5.Disconnect the trimmer/edger from the power supply

when not in use

before servicing

6.Do not force trimmer/edger.It will do the job better and with less likelihood of a risk of injury at the rate for which it was designed.

7.Do not abuse power cord. Never pull or carry trimmer/edger by power cord. Never yank cord to disconnect from receptacle. Keep power cord from heat, oil, and sharp edges.

8.Keep hands and feet away from cut- ting area.

MAINTENANCE AND STORAGE OF TRIMMER/ EDGER

1.Maintain trimmer/edger with care.

Inspect trimmer/edger cord pe- riodically, and if damaged, have it repaired by a qualified service facility.

Inspect extension cords periodically and replace if damaged.

If trimmer/edger is not working properly, has been dropped, dam- aged, left outdoors, or dropped into water, have it repaired by a qualified service center.

Keep handles dry, clean, and free from oil and grease.

Keep guards in place and in work- ing order.

2.Check damaged parts.

If a part is damaged, carefully check the damaged part before using the trimmer/edger. Make sure the part will operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other condition that may affect its operation.

A guard or other part that is dam- aged should be properly repaired or replaced by a qualified service center unless indicated elsewhere in this manual.

Use only geniune Remington® replacement parts and accessories. These are available from your local dealer. Use of any non-Reming- ton® parts or accessories could lead to injury to the user, damage to the unit, and void you warranty.

3.Servicing of Double-Insulated Tools:

In a double-insulated tool, two systems of insulation are provided instead of grounding. No ground- ing means is provided on a double- insulated tool, nor should a means for grounding be added to the tool. Servicing a double-insulated tool requires extreme care and knowl- edge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated tool must be identical to the parts they replace.

4.Store idle trimmer/edger indoors. When not in use,store trimmer/edger and extension cord indoors in a dry location. Store trimmer/edger above the reach of children or in a locked area out of the reach of children.

This manual is your guide to safe and proper operation of the trimmer/edger.

SAVE THESE

INSTRUCTIONS.

118035

Image 6
Contents Electric TRIMMER/EDGER 118035 Table of contents Welcome Important safety information Dress properly when operating trim- mer/edgerAvoid Dangerous Environments Keep hands and feet away from cut- ting area Important Safety InformationStay alert. Watch what you are doing. Use common sense Servicing of Double-Insulated ToolsProduct identification SpecificationsAttaching Cutting Guard Edging Wheel Trimmer/edger assemblyAssembling Trimmer/Edger Screw hole at top of cutting guard seeAttaching Adjustable Front Handle Remove the knob and bolt from front handle see FigureExtension Cords Connecting Extension CordTrimmer/edger operation Inspect cord often. Replace if damagedStarting the Trimmer/Edger Adjusting Shaft LengthOperating Trimmer/Edger Keep bystanders away from work areaTrimming Advancing Trimmer Line Trimmer/Edger OperationRemoving the Spool 14 Removing spool cover and spool 20 Arranging line into spool 25 Replacing spool into spool housing Using Edger Converting to EdgerRelease the shaft rotation button Donotusechlorinatedcleaning Trimmer/edger maintenanceCleaning Maintenance Solvents,CarbonTetrachloride Kerosene, or GasolineTechnical Service TroubleshootingReplacement Spool Replacement SpoolWarranty information Remington Electric TRIMMER/EDGER Limited Warranty118035 PODADORA/RECORTABORDES Eléctrica Con doble aislamiento118035 Tabla de contenidos PODADORA/RECORTABORDES Eléctrica RemingtonSi tiene alguna pregunta o problema BienvenidoModelo Número Fecha de Compra Lugar de Compra Importante información sobre la seguridad SJTOW-AMantenga las manos y los pies lejos del área de corte Capítulo 1 Importante información sobre la seguridadCuando no la use Antes de darla servicio Mantenga las asas secas, limpias y sin aceite ni grasaIdentificación del producto EspecificacionesEnsamble de la podadora/recortabordes Ensamble de la podadora/recortabordesSujeción del asa frontal regulable Retire la perilla y el perno del asa frontal vea la FiguraOperación de la podadora/recortabordes Cordones de extensiónInspeccione a menudo el cordón.Cámbielo si está dañado Operación de la podadora/recortabordes Mantenga a los curiosos lejos del área de trabajoRegulación de la longitud del eje Arranque de la podadora/re- cortabordesCapítulo 4 Operación de la podadora/recortabordes Corte Retiro del carreteFigura 4-14 Retiro de la tapa y del carrete Figura 4-20 Colocación de la cuerda en el carrete Figura 4-26 Reposición de la tapa del carrete en la carcasa Conversión en recortabordes Uso como recortabordesMantenimiento de la podadora/recortabordes Limpieza y mantenimientoAnálisis de averías Carrete de repuestoServicio Técnico Información sobre la garantía 118035 118035 Électriques Double Isolation118035 Table des matières TAILLE-BORDURES / COUPE-BORDURES Électriques RemingtonmdNuméro de modèle Date d’achat Endroit d’achat 800 Service en anglais seulementBienvenue Pour toute question ou problèmeImportants renseignements sur la sécurité Évitez les endroits dangereuxGardez les mains et les pieds à l’écart de la zone de coupe Chapitre 1 Importants renseignements de sécuritéAvant d’en faire l’entretien Entretenez avec soin le taille-bordures / coupe-borduresIdentification du produit Fiche techniqueAssemblage du taille-bordures / coupe-bordures Assemblage du taille-bordures / coupe-borduresMise en place du protecteur et du disque de coupe Confortable, puis serrez fermement Mise en place de la poignée avant réglableSerrer voir la Figure Le bouton. Évitez toutefois de trop le SerrerUtilisation du taille-bordures / coupe-bordures Rallonges électriquesBranchement de la rallonge électrique Utilisez cet outil Portez une protection ocuLaire, des pantalons longs et Assurez-vous que personneRéglage de la longueur de l’arbre Chapitre 4 Utilisation du taille-bordures / coupe-borduresRallonge du fil de coupe Remplacement du filTaille des bordures Retrait de la bobine14 Retrait du couvercle de la bobine et de la bobine 22 Mise en place de la bague de retenue sur la bobine 25 Mise en place de la bobine dans le boîtier Utilisation du coupe-bordures Relâchez le bouton de rotation de l’arbreEntretien du taille-bordures / coupe-bordures Entretien et nettoyageDépannage Remplacement de la bobineService technique Bobine de remplaceRenseignements sur la garantie 118035 118035-01 Rev. a 12/05

ST3812B, ST4514B specifications

The Remington ST3812B and ST4514B are two innovative hair styling tools designed to cater to various hair types and styling preferences. These hair straighteners combine advanced technologies to ensure an efficient, safe, and stylish experience for users.

The Remington ST3812B, often celebrated for its compact design, features ceramic plates that provide even heat distribution, minimizing the chances of hot spots that can damage hair. With a fast heat-up time of just 30 seconds, this straightener is perfect for those with busy schedules who need a quick styling solution. The straightener offers multiple temperature settings, allowing users to choose the best heat level for their specific hair type, whether it be fine, thick, or somewhere in between. This feature not only promotes hair health but also enhances styling versatility.

In addition, the ST3812B is equipped with a safety lock feature that secures the plates together for easy storage and transportation. The ergonomic design ensures comfortable handling, making it easier to create those coveted sleek and straight styles without causing unnecessary strain on the wrists.

On the other hand, the Remington ST4514B caters to a broader audience with its larger plates, which are ideal for users with long or thick hair. This model integrates a unique Digital Heat Control technology, enabling precise temperature adjustments based on the specific needs of the hair. With a maximum heat setting of 230 degrees Celsius, the ST4514B is designed to tame even the most unruly locks while ensuring minimal damage.

Additionally, the ST4514B features a floating plate design, which adjusts to different hair sections for enhanced styling. This flexibility allows the straightener to glide effortlessly through the hair, reducing tugging and breakage. For users concerned about hair health, the inclusion of protective ceramic materials helps to smooth the hair cuticle, leaving a shiny and well-finished look.

Both models come with a 60-minute auto shut-off function, providing peace of mind to users who may forget to turn off their devices after use. This added safety feature is especially advantageous for those with hectic lifestyles.

In summary, both the Remington ST3812B and ST4514B are exceptional hair straighteners that boast a range of features aimed at delivering professional results at home. With their combination of innovative technologies, safety features, and user-friendly designs, they stand out as reliable choices for anyone looking to achieve salon-quality hair styling with ease.