RedMax BCZ3001SW-CA, BCZ3001S-CA manual Operation, OP1 OP2 Starting Engine, OP3, OP4

Page 28

English

8. Operation

OP1

OP2

(1)

 

■STARTING ENGINE

WARNING

The cutting head will start rotating upon the engine starts.

1.

Rest the unit on a flat, firm place. Keep the cutting

 

head off the ground and clear of surrounding objects

 

as it will start rotating upon starting of the engine.

2.

Push the primer pump several times until overflown

 

fuel flows out in the clear tube. (OP1)

3.

Move the choke lever to the closed position. (OP2)

4.

Set the stop switch to the “Start” position. While

 

pulling the throttle lever, push the throttle set button,

OP3

(2)

(3)

(5)

and release the throttle, then the throttle lever is in to

the “Start position”. (OP3)

5. While holding the unit firmly, pull out the starter rope

quickly until engine fires. (OP4)

(1) choke lever

(2) close

(3) open

(4) stop switch

(5) start

(6) stop

(7) Throttle set button

(6)

(4)

(7)

BCZ3001S BCZ3001S-CA

IMPORTANT

•Avoid pulling the rope to its end or returning it by releasing the knob. Such actions can cause starter failures.

(4)

(5)

BCZ3001SW(6) BCZ3001SW-CA

OP4

6.Move the choke lever downward to open the choke. And restart engine. (OP2)

7.Allow the engine to warm up for several minutes before starting operation.

NOTE

1.When restarting the engine immediately after stopping it, leave the choke open.

2.Overchoking can make the engine hard to start due to excess fuel. When the engine failed to start after several attempts, open the choke and repeat pulling the rope, or remove the spark plug and dry it.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual BCZ3001SW Parts locationBCZ3001S-CA BCZ3001SW-CA Emplacement des pieces Situación de las piezas BCZ3001S-CASpecifications Dry weightFiche technique EspecificaciohesSymbols on the machine PositionEmplacement PosiciónWorking Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheStarting the Engine Using the ProductCut only materials recommended by Arranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoFor use with the RedMax product Handling FuelRefill after cooling the engine TransportationManipulation DU Carburant Manipulación DEL CombustibleLlenar una vez que el motor se haya enfriado TransportSet up Assemblage Montaje Fuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation OP1 OP2 Starting EngineCutting head will start rotating upon the engine starts OP3Fonctionnement Uso Palanca del estrangulador 2 cerrarAdjusting Throttle Cable Adjusting Idling Speed OP6OP5 OP6 Stopping Engine OP3Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorReglage DU Ralenti OP6 Travail DE Coupe Utilisation DE LA Tete DE FILAdjusting the Line Length OP7Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 MA2 MA3 Refilling Trimming Line MA1AIR Filter Fuel FilterEntretien Mantenimiento Filtre a AIRFiltre a Carburant Filtro DE AireReplacement Plug is a NGK CMR7H MA4Spark Plug Tightening TorqueCouple DE Serrage SilencieuxPARE-ETINCELLES LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7HMA6 Angle Transmission MA6Intake AIR Cooling Vent MA7Transmission D’ANGLE MA6 Transmisión DEL Ángulo MA6 Cilindro Toma de aire de refrigeración posteriorProcedures to be Performed After Every 100 Hours of USE StorageDisposal MA8Rangement Almacenamiento Entretien MantenimientoMise au rebut Eliminación OPT1 OPT2 Optional blade usageBracket Handle Utilisation de la lame optionnelle Uso de hoja opcional Couple DE Serrage PAR Torsor26 43,5 pulg.-lbs Moyeu 3583-14101 Poignée en J 6367-14200OPT3 OPT4 OPT5 SET UP the BladeChoose the Blade Elija LA Hoja Choisir LA LameMise EN Place DE LA Lame Monte LA Hoja Cutting Method OPT6 OPT7 OPT8 OPT9Operation Methode DE Coupe FonctionnementMétodo DE Corte USOWhat causes blade thrust Controlling Blade ThrustHow you can reduce the chance of blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaMaintenance Blade OPT10How you can maintain the best control 22, 24-tooth blade Tooth blade Point OPT10Comment conserver le meilleur contrôle de la machine Cuál es la mejor forma de mantener el controlEntretien Lame Mantenimiento Hoja13. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Brushcutters NotaDrive Unit BCZ3001S/BCZ3001S-CA S/N 60100101 and up Optional Blade & Accessories Drive Unit BCZ3001SW/BCZ3001SW-CA S/N 60100101 and up Optional Blade Parts list Special Tools Part Number Description QtyManufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control BCZ3001S/BCZ3001SWMesures DE Lutte Contre LES Emissions Control DE Emisiones

BCZ3001SW-CA, BCZ3001S-CA, BCZ3001SW, BCZ3001S specifications

The RedMax BCZ3001S, BCZ3001SW, BCZ3001S-CA, and BCZ3001SW-CA are premium brushcutters designed for both professional landscapers and dedicated homeowners. Each model combines power, efficiency, and user comfort, making them ideal for tackling tough lawn care tasks.

One of the standout features of these models is their lightweight design. Weighing in at just under 10 pounds, they are highly maneuverable, allowing operators to handle extended jobs without experiencing excessive fatigue. The ergonomic design incorporates a comfortable handle system, which reduces strain on the user’s arms and back. This thoughtful engineering ensures that each machine can be used for extended periods with minimal discomfort.

All four models are powered by RedMax's advanced 30.5cc engine that delivers robust performance. The engine provides enough power to easily cut through dense vegetation, grasses, and brambles. The inclusion of a reliable ignition system ensures rapid starts and smooth operation, minimizing downtime during critical mowing or trimming sessions.

The RedMax BCZ3001 series is equipped with a cutting-edge dual-line trimmer head that offers greater efficiency. This head allows for faster cutting speeds and improved line durability, enabling users to mitigate frequent line replacement — a common frustration with traditional models. Additionally, the head's bump feed feature allows for easy line advancement, providing seamless operation.

Both the BCZ3001SW and BCZ3001SW-CA versions come with a coupled brush blade and a “Swinging Blade” cutting system. This feature allows users to utilize either a trimmer line or a blade for more versatility depending on the job's requirements. The ability to switch between cutting systems accommodates a range of tasks, from trimming delicate flower beds to clearing more robust weeds.

Safety is a paramount concern for RedMax, which is why these models include essential features such as anti-vibration technology. This technology minimizes vibrations generated during operation, enhancing comfort and control while decreasing the likelihood of operator fatigue.

In conclusion, the RedMax BCZ3001S, BCZ3001SW, BCZ3001S-CA, and BCZ3001SW-CA brushcutters represent a robust solution for anyone seeking a reliable, efficient, and powerful tool for lawn care. With their lightweight builds, advanced engine technology, versatile cutting systems, and user-centric designs, these models stand out in the competitive market of outdoor power equipment. Whether you are a homeowner or a professional, these brushcutters will undoubtedly exceed your landscaping expectations.
Top Page Image Contents