RedMax BCZ3001SW-CA manual Manufacturer’s warranty coverage, Owner’s warranty responsibilities

Page 62

CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resources Board and ZENOAH AMERICA, INC. are pleased to explain the emission control system warranty on your 2007 and later small off-road engine. In California, new small off-road engines must be designed, built and equipped to meet the state’s stringent anti-smog standards. ZENOAH AMERICA, INC. must warrant the emission control system on your small off-road engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carburetor, fuel tank and the ignition system.

Where a warrantable condition exists, ZENOAH AMERICA, INC. will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

Manufacturer’s warranty coverage:

The 2007 and later small off-road engines are warranted for two years. If any emission- related part on your engine is defective, the part will be repaired or replaced by ZENOAH AMERICA, INC.

Owner’s warranty responsibilities:

–As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your owner’s manual. ZENOAH AMERICA, INC. recommends that you retain all receipts covering maintenance on your small off-road engine, but ZENOAH AMERICA, INC. can not deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

–As the small off-road engine owner, you should be aware, however, that ZENOAH AMERICA, INC. may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modification.

–You are responsible for presenting your small off-road engine to a ZENOAH AMERICA, INC. distribution center as soon as a problem exists. The warranty repairs should be completed in e reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact ZENOAH AMERICA, INC. at (770)-381-5147 or you can write to

ZENOAH AMERICA, INC.

1100 Laval Blvd. Suite 110

Lawrenceville, Georgia 30043

BCZ3001S-CA, BCZ3001SW-CA only

Page 61 Page 63
Image 62
Page 61 Page 63
Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido BCZ3001S-CA BCZ3001SW-CA Parts locationBCZ3001SW Emplacement des pieces Situación de las piezas BCZ3001S-CASpecifications Dry weightFiche technique EspecificaciohesSymbols on the machine PositionEmplacement PosiciónWorking Circumstance For safe operationWorking Condition Condiciones DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail PrecaucionesWorking Plan Before Starting the EngineDE LA Machine Plan DE TravailPlan DE Trabajo Avant DE Mettre LE Moteur EN MarcheCut only materials recommended by Using the ProductStarting the Engine Utilisation DE LA Machine USO DEL Producto Demarrage DU MoteurArranque DEL Motor Maintenance If Someone ComesSI Alguien SE Aproxima SI QUELQU’UN S’APPROCHEEntretien MantenimientoRefill after cooling the engine For use with the RedMax productHandling Fuel TransportationLlenar una vez que el motor se haya enfriado Manipulation DU CarburantManipulación DEL Combustible TransportSet up Assemblage Montaje Recommended Mixing Ratio Gasoline 50OIL When using RedMax/ZENOAH genuine oilFuel Lors de l’utilisation de la véritable huile RedMax/ZENOAH Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Cutting head will start rotating upon the engine starts OperationOP1 OP2 Starting Engine OP3Fonctionnement Uso Palanca del estrangulador 2 cerrarOP5 Adjusting Throttle CableAdjusting Idling Speed OP6 OP6 Stopping Engine OP3Reglage DU Ralenti OP6 Reglage Câble D’ACCÉLÉRATEURAjuste Cable DEL Acelerador Travail DE Coupe Utilisation DE LA Tete DE FILAdjusting the Line Length OP7Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoAIR Filter MA1 MA2 MA3Refilling Trimming Line MA1 Fuel FilterFiltre a Carburant Entretien MantenimientoFiltre a AIR Filtro DE AireSpark Plug Replacement Plug is a NGK CMR7HMA4 Tightening TorquePARE-ETINCELLES Couple DE SerrageSilencieux LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7HIntake AIR Cooling Vent MA6Angle Transmission MA6 MA7Transmission D’ANGLE MA6 Transmisión DEL Ángulo MA6 Cilindro Toma de aire de refrigeración posteriorDisposal Procedures to be Performed After Every 100 Hours of USEStorage MA8Mise au rebut Eliminación Entretien MantenimientoRangement Almacenamiento Bracket Handle Optional blade usageOPT1 OPT2 26 43,5 pulg.-lbs Utilisation de la lame optionnelle Uso de hoja opcionalCouple DE Serrage PAR Torsor Moyeu 3583-14101 Poignée en J 6367-14200Choose the Blade SET UP the BladeOPT3 OPT4 OPT5 Mise EN Place DE LA Lame Monte LA Hoja Choisir LA LameElija LA Hoja Operation OPT6 OPT7 OPT8 OPT9Cutting Method Método DE Corte Methode DE CoupeFonctionnement USOHow you can reduce the chance of blade thrust Controlling Blade ThrustWhat causes blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaHow you can maintain the best control Maintenance BladeOPT10 22, 24-tooth blade Tooth blade Point OPT10Entretien Lame Comment conserver le meilleur contrôle de la machineCuál es la mejor forma de mantener el control Mantenimiento HojaGuide de localisation des pannes Troubleshooting guide13. Guía de localización y solución de problemas Brushcutters NotaDrive Unit BCZ3001S/BCZ3001S-CA S/N 60100101 and up Optional Blade & Accessories Drive Unit BCZ3001SW/BCZ3001SW-CA S/N 60100101 and up Optional Blade Parts list Special Tools Part Number Description QtyManufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Mesures DE Lutte Contre LES Emissions Emission ControlBCZ3001S/BCZ3001SW Control DE Emisiones

BCZ3001SW-CA, BCZ3001S-CA, BCZ3001SW, BCZ3001S specifications

The RedMax BCZ3001S, BCZ3001SW, BCZ3001S-CA, and BCZ3001SW-CA are premium brushcutters designed for both professional landscapers and dedicated homeowners. Each model combines power, efficiency, and user comfort, making them ideal for tackling tough lawn care tasks.

One of the standout features of these models is their lightweight design. Weighing in at just under 10 pounds, they are highly maneuverable, allowing operators to handle extended jobs without experiencing excessive fatigue. The ergonomic design incorporates a comfortable handle system, which reduces strain on the user’s arms and back. This thoughtful engineering ensures that each machine can be used for extended periods with minimal discomfort.

All four models are powered by RedMax's advanced 30.5cc engine that delivers robust performance. The engine provides enough power to easily cut through dense vegetation, grasses, and brambles. The inclusion of a reliable ignition system ensures rapid starts and smooth operation, minimizing downtime during critical mowing or trimming sessions.

The RedMax BCZ3001 series is equipped with a cutting-edge dual-line trimmer head that offers greater efficiency. This head allows for faster cutting speeds and improved line durability, enabling users to mitigate frequent line replacement — a common frustration with traditional models. Additionally, the head's bump feed feature allows for easy line advancement, providing seamless operation.

Both the BCZ3001SW and BCZ3001SW-CA versions come with a coupled brush blade and a “Swinging Blade” cutting system. This feature allows users to utilize either a trimmer line or a blade for more versatility depending on the job's requirements. The ability to switch between cutting systems accommodates a range of tasks, from trimming delicate flower beds to clearing more robust weeds.

Safety is a paramount concern for RedMax, which is why these models include essential features such as anti-vibration technology. This technology minimizes vibrations generated during operation, enhancing comfort and control while decreasing the likelihood of operator fatigue.

In conclusion, the RedMax BCZ3001S, BCZ3001SW, BCZ3001S-CA, and BCZ3001SW-CA brushcutters represent a robust solution for anyone seeking a reliable, efficient, and powerful tool for lawn care. With their lightweight builds, advanced engine technology, versatile cutting systems, and user-centric designs, these models stand out in the competitive market of outdoor power equipment. Whether you are a homeowner or a professional, these brushcutters will undoubtedly exceed your landscaping expectations.
Top Page Image Contents