OPT10, How you can maintain the best control

RedMax BCZ3001SW-CA, BCZ3001S-CA OPT10, How you can maintain the best control, Maintenance Blade

Page 52

OPT10

English

12. Optional blade usage

3.How you can maintain the best control:

a.Keep a good, firm grip on the unit with both hands. A firm grip can help neutralize bounce. Keep your right and left hands completely around the respective handles.

b.Keep both feet spread apart in a comfortable stance and yet braced for the possibility that the unit could bounce. Do not overreach. Keep firm footing and balance.

■MAINTENANCE BLADE

• Check the blade and the fasteners for looseness, cracking, or bending.

• Check the cutting edges and reform with a flat file.

(A)22, 24-tooth blade

(B)8-tooth blade

Point (OPT10) :

1.Keep the end corner sharp.

2.Round the root of the edge, using round file.

3.Do not use water when using a grinder.

IMPORTANT

•It is recommended that filing should be done by professionals.

•Especially regarding filing the 22,24-tooth blade, Leave it to the professionals.

■TRANSPORTING THE UNIT

•When you finish cutting in one location and wish to continue work in another spot, turn off the engine, and lift up the unit and carry it paying attention for the blade.

•Never forget to place the protective cover over the blades.

•When transporting the unit over long distances, detach the blade fix the unit by ropes.

Image 52

Contents

OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual BCZ3001SW Parts locationBCZ3001S-CA BCZ3001SW-CA Emplacement des pieces Situación de las piezas BCZ3001S-CASpecifications Dry weightFiche technique EspecificaciohesSymbols on the machine PositionEmplacement PosiciónWorking Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheStarting the Engine Using the ProductCut only materials recommended by Arranque DEL Motor Demarrage DU MoteurUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoFor use with the RedMax product Handling FuelRefill after cooling the engine TransportationManipulation DU Carburant Manipulación DEL CombustibleLlenar una vez que el motor se haya enfriado TransportSet up Assemblage Montaje Fuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation OP1 OP2 Starting EngineCutting head will start rotating upon the engine starts OP3Fonctionnement Uso Palanca del estrangulador 2 cerrarAdjusting Throttle Cable Adjusting Idling Speed OP6OP5 OP6 Stopping Engine OP3Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorReglage DU Ralenti OP6 Travail DE Coupe Utilisation DE LA Tete DE FILAdjusting the Line Length OP7Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 MA2 MA3 Refilling Trimming Line MA1AIR Filter Fuel FilterEntretien Mantenimiento Filtre a AIRFiltre a Carburant Filtro DE AireReplacement Plug is a NGK CMR7H MA4Spark Plug Tightening TorqueCouple DE Serrage SilencieuxPARE-ETINCELLES LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7HMA6 Angle Transmission MA6Intake AIR Cooling Vent MA7Transmission D’ANGLE MA6 Transmisión DEL Ángulo MA6 Cilindro Toma de aire de refrigeración posteriorProcedures to be Performed After Every 100 Hours of USE StorageDisposal MA8Rangement Almacenamiento Entretien MantenimientoMise au rebut Eliminación OPT1 OPT2 Optional blade usageBracket Handle Utilisation de la lame optionnelle Uso de hoja opcional Couple DE Serrage PAR Torsor26 43,5 pulg.-lbs Moyeu 3583-14101 Poignée en J 6367-14200OPT3 OPT4 OPT5 SET UP the BladeChoose the Blade Elija LA Hoja Choisir LA LameMise EN Place DE LA Lame Monte LA Hoja Cutting Method OPT6 OPT7 OPT8 OPT9 Operation Methode DE Coupe FonctionnementMétodo DE Corte USOWhat causes blade thrust Controlling Blade ThrustHow you can reduce the chance of blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaMaintenance Blade OPT10How you can maintain the best control 22, 24-tooth blade Tooth blade Point OPT10Comment conserver le meilleur contrôle de la machine Cuál es la mejor forma de mantener el controlEntretien Lame Mantenimiento Hoja13. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Brushcutters NotaDrive Unit BCZ3001S/BCZ3001S-CA S/N 60100101 and up Optional Blade & Accessories Drive Unit BCZ3001SW/BCZ3001SW-CA S/N 60100101 and up Optional Blade Parts list Special Tools Part Number Description QtyManufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control BCZ3001S/BCZ3001SWMesures DE Lutte Contre LES Emissions Control DE Emisiones

RedMax BCZ3001SW-CA, BCZ3001S-CA OPT10, How you can maintain the best control, Maintenance Blade