RedMax BCZ3001SW-CA manual MA1 MA2 MA3, Refilling Trimming Line MA1, AIR Filter, Fuel Filter

Page 36

MA1

MA2

(1)

MA3

(1)

English

9.Maintenance

REFILLING TRIMMING LINE (MA1)

1.For replacement line, use a diameter of .095in (2.4mm). The spool is capable for a line upto 20ft (6m) on the 4” head. Avoid using a larger line as it may cut down the trimming performance.

WARNING

For safety reasons, do not use metalreinforced line.

2.Pinch the slotted area on the both sides of the spool housing to unhook the bottom cap.

3.Take out the spool and pull off the old line. Fold new line so that one half line is 4.7in.(12cm) shorter than another half. And then, hook bended end in the slot of the spool.

4.Wind up the line in the correct direction as indicated on the spool.

5.Hook each end of the line in the slot on the edge of the spool, and then put the ends through the eyelets on the housing. Make sure that the spring and the washers are in place.

6.While holding the spool against the housing, pull the line ends to release them from the slot.

7.Line up the slot on the bottom cap with the hook on the housing, press the cap against the housing until it clicks.

WARNING

Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury.

AIR FILTER

The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace with a new one. (MA2)

(1) air filter

FUEL FILTER

When the engine runs short of fuel supply, check the fuel cap and the fuel filter for blockage. (MA3)

(1) fuel filter

36

Image 36
Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Parts location BCZ3001SWBCZ3001S-CA BCZ3001SW-CA Emplacement des pieces Situación de las piezas BCZ3001S-CASpecifications Dry weightFiche technique EspecificaciohesSymbols on the machine PositionEmplacement PosiciónFor safe operation Working ConditionWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondiciones DE Trabajo PrecaucionesWorking Plan Before Starting the EnginePlan DE Travail Plan DE TrabajoDE LA Machine Avant DE Mettre LE Moteur EN MarcheUsing the Product Starting the EngineCut only materials recommended by Demarrage DU Moteur Arranque DEL MotorUtilisation DE LA Machine USO DEL Producto Maintenance If Someone ComesSI QUELQU’UN S’APPROCHE EntretienSI Alguien SE Aproxima MantenimientoFor use with the RedMax product Handling FuelRefill after cooling the engine TransportationManipulation DU Carburant Manipulación DEL CombustibleLlenar una vez que el motor se haya enfriado TransportSet up Assemblage Montaje When using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile RedMax/ZENOAH Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Combustible SIN Aceite Gasolina Cruda Operation OP1 OP2 Starting EngineCutting head will start rotating upon the engine starts OP3Fonctionnement Uso Palanca del estrangulador 2 cerrarAdjusting Throttle Cable Adjusting Idling Speed OP6OP5 OP6 Stopping Engine OP3Reglage Câble D’ACCÉLÉRATEUR Ajuste Cable DEL AceleradorReglage DU Ralenti OP6 Travail DE Coupe Utilisation DE LA Tete DE FILAdjusting the Line Length OP7Reglage DE LA Longeur DU FIL DE Coupe Ajuste DE LA Longitud DE LA LíneaMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoMA1 MA2 MA3 Refilling Trimming Line MA1AIR Filter Fuel FilterEntretien Mantenimiento Filtre a AIRFiltre a Carburant Filtro DE AireReplacement Plug is a NGK CMR7H MA4Spark Plug Tightening TorqueCouple DE Serrage SilencieuxPARE-ETINCELLES LA Bujía DE Recambio Debe SER UNA Bujía NGK CMR7HMA6 Angle Transmission MA6Intake AIR Cooling Vent MA7Transmission D’ANGLE MA6 Transmisión DEL Ángulo MA6 Cilindro Toma de aire de refrigeración posteriorProcedures to be Performed After Every 100 Hours of USE StorageDisposal MA8Entretien Mantenimiento Rangement AlmacenamientoMise au rebut Eliminación Optional blade usage OPT1 OPT2Bracket Handle Utilisation de la lame optionnelle Uso de hoja opcional Couple DE Serrage PAR Torsor26 43,5 pulg.-lbs Moyeu 3583-14101 Poignée en J 6367-14200SET UP the Blade OPT3 OPT4 OPT5Choose the Blade Choisir LA Lame Elija LA HojaMise EN Place DE LA Lame Monte LA Hoja OPT6 OPT7 OPT8 OPT9 Cutting MethodOperation Methode DE Coupe FonctionnementMétodo DE Corte USOControlling Blade Thrust What causes blade thrustHow you can reduce the chance of blade thrust Controle DES Coups DE Recul Control DEL Contragolpe DE LA HojaMaintenance Blade OPT10How you can maintain the best control 22, 24-tooth blade Tooth blade Point OPT10Comment conserver le meilleur contrôle de la machine Cuál es la mejor forma de mantener el controlEntretien Lame Mantenimiento HojaTroubleshooting guide 13. Guía de localización y solución de problemasGuide de localisation des pannes Brushcutters NotaDrive Unit BCZ3001S/BCZ3001S-CA S/N 60100101 and up Optional Blade & Accessories Drive Unit BCZ3001SW/BCZ3001SW-CA S/N 60100101 and up Optional Blade Parts list Special Tools Part Number Description QtyManufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control BCZ3001S/BCZ3001SWMesures DE Lutte Contre LES Emissions Control DE Emisiones

BCZ3001SW-CA, BCZ3001S-CA, BCZ3001SW, BCZ3001S specifications

The RedMax BCZ3001S, BCZ3001SW, BCZ3001S-CA, and BCZ3001SW-CA are premium brushcutters designed for both professional landscapers and dedicated homeowners. Each model combines power, efficiency, and user comfort, making them ideal for tackling tough lawn care tasks.

One of the standout features of these models is their lightweight design. Weighing in at just under 10 pounds, they are highly maneuverable, allowing operators to handle extended jobs without experiencing excessive fatigue. The ergonomic design incorporates a comfortable handle system, which reduces strain on the user’s arms and back. This thoughtful engineering ensures that each machine can be used for extended periods with minimal discomfort.

All four models are powered by RedMax's advanced 30.5cc engine that delivers robust performance. The engine provides enough power to easily cut through dense vegetation, grasses, and brambles. The inclusion of a reliable ignition system ensures rapid starts and smooth operation, minimizing downtime during critical mowing or trimming sessions.

The RedMax BCZ3001 series is equipped with a cutting-edge dual-line trimmer head that offers greater efficiency. This head allows for faster cutting speeds and improved line durability, enabling users to mitigate frequent line replacement — a common frustration with traditional models. Additionally, the head's bump feed feature allows for easy line advancement, providing seamless operation.

Both the BCZ3001SW and BCZ3001SW-CA versions come with a coupled brush blade and a “Swinging Blade” cutting system. This feature allows users to utilize either a trimmer line or a blade for more versatility depending on the job's requirements. The ability to switch between cutting systems accommodates a range of tasks, from trimming delicate flower beds to clearing more robust weeds.

Safety is a paramount concern for RedMax, which is why these models include essential features such as anti-vibration technology. This technology minimizes vibrations generated during operation, enhancing comfort and control while decreasing the likelihood of operator fatigue.

In conclusion, the RedMax BCZ3001S, BCZ3001SW, BCZ3001S-CA, and BCZ3001SW-CA brushcutters represent a robust solution for anyone seeking a reliable, efficient, and powerful tool for lawn care. With their lightweight builds, advanced engine technology, versatile cutting systems, and user-centric designs, these models stand out in the competitive market of outdoor power equipment. Whether you are a homeowner or a professional, these brushcutters will undoubtedly exceed your landscaping expectations.