Makita EM5250CA Cleaning of AIR Cleaner, Points on OIL, Points in Handling Air Cleaner Element

Page 19

3) Place waste or paper near the oil refill port.

4)Detach the oil gauge, and drain oil, tilting the main unit toward the oil refill port.

Drain oil in a container.

5)Keep the engine level, and feed new oil up to the edge of the oil refill port. In refill, use a lubricant refill container.

6)After refill, securely tighten the oil gauge. Insufficient tightening of the oil gauge will lead to oil leakage.

Waste or paper

POINTS ON OIL

–Never discard replaced engine oil in garbage, earth or sewage ditch. Disposal of oil is regulated by law. In disposal, always follow the relevant laws and regulations. For any points remaining unknown, contact Authorized Service Agent.

–Oil will deteriorate even when it is kept unused. Perform inspection and replacement at regular intervals (replace with new oil every 6 months).

CLEANING OF AIR CLEANER

DANGER:

Interval of Cleaning and Inspection: Daily (every 10 operating hours)

–Turn the choke lever to the full close side, and keep the carburetor off from dust or dirt.

–Remove the air cleaner cover-fixing bolts.

–Pull the cover lower side and detach the air cleaner cover.

–If oil adheres to the element (sponge), squeeze it firmly.

–For heavy contamination:

Element (sponge)

Air cleaner cover

Plate

Breather Part

neutral detergent, and dry it completely.

2) Clean the element (felt) with gasoline, and dry it completely.

–Before attaching the element, be sure to dry it completely. Insufficient drying of the element may lead to difficult startup.

–Wipe out with waste cloth, oil adhering around the air cleaner cover and plate breather.

–Immediately after cleaning is finished, attach the cleaner cover and tighten it with fixing bolts. (In remounting, first place the upper claw, and then the lower claw.)

Points in Handling Air Cleaner Element

–Clean the element several times a day, if excessive dust adheres to it.

–If operation continues with the element remaining not cleared of oil, oil in the air cleaner may fall outside, resulting in oil contamination.

Element (felt)

Fixing bolt

Pick this part and remove the element (felt).

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents EM4250CA EM4251CA English SymbolsPersonal protective equipment Safety InstructionsGeneral Instructions Intended use of the machineRefuelling Kickback prevention Maintenance instructionsMethod of operation KickbackPackaging When asking for help, please give the following informationNever straighten or weld damaged cutting tools First AidEM4251/EM4251CA EM4250/EM4250CA Model Technical Data EM4250, EM4251EM4250/EM4250CA Brush Cutter EM4251/EM4251CA String trimmer Designation of PartsFor machines with U Handle models Mounting of HandleFor machines with Loop Handle models Mounting of Protector For EM4250/EM4250CA with the hex wrench still in place Mounting of Cutter Blade or Nylon Cutter HeadMounting of nylon cutting head Before Start of Operation Point 1 in Replacement of Oil Oil GaugeInspection and Refill of Engine Oil Storage Ofmachineandrefilltank RefuelingCorrect Handling of Machine Points in Operation and HOW to StopStarting Open For machine with U Handle or Loop HandleStartup after warm-up operation Adjustment of LOW-SPEED Rotation IdlingResharpening the Cutting Tool StoppingOperation Nylon Cutting HeadReplacing the nylon cord Daily checkup and maintenance Replacement of Engine OILServicing Instructions Points in Handling Air Cleaner Element Cleaning of AIR CleanerPoints on OIL Replacement of Gaskets and Packings Cleaning of Fuel FilterReplacement of Fuel Pipe Cleaning of PartsStorage Fault locationOperating time Troubleshooting Emission Compliance Period MANUFACTURER’S Warranty Coverage Page Every 8 hours daily Every 8 hours daily ProcedureFederal Emission Component Defect Warranty Obtaining Warranty Service HOW to Make a Claim Français SymbolesÉquipement personnel de protection Consignes DE SécuritéInstructions générales Utilisation spéciale de la machineMètres RavitaillementOutils de coupe Instructions de maintenanceMéthode dutilisation Effet de retourEmballage Premier secoursCaracteristiques Techniques EM4250/EM4250CA, EM4251/EM4251CA Nomenclature DES Pièces Pour les modèles à polgnée en U Montage DE LA PoignéeMachines à poignée simple Montage DU Dispositif DE Protection Montage du dispositif de coupe à fil Montage DE LA Lame DE Coupe OU DE LA Téte DE Coupe À FILControle ET Ravitaillement DE L’HUILE Moteur Avant Mise EN MarcheENTREPÔSAGEDEL’APPAREILETDURÉSERVOIRDERAVITALLEMENT RavitaillementRetrait Manipulation Correcte DE LA MachineConsignes DE Mise EN Marche ET Arrêt DE LA Machine Fixation du harnaisConsignes de sécurité lors du fonctionnement Pour les machines à poignée en U ou en BoucleVerification DE Larotation Apetite Vitesse Réaffûtage DE Loutil DE CoupeReglage DE LA Marche a Petite Vitesse AU Ralenti Démarrage après réchauffageTête de coupe à fil en nylon Remplacement du fil en nylonFonctionnement Contrôle et opérations de maintenance réguliers Remplacement DE L’HUILE a MoteurInstructions Relatives AUX Réparations ESSENTIELSPOURL’HUILE Nettoyage DU Filtre a AIRGraissage DU Carter D’ENGRENAGE Remplacement DU Tuyau a CarburantRemplacement DES Joints ET Garnitures Contôle DE LA Bougie DallumageLocalisation des défauts RemisageDurée de marche Depannage Lista de contenidos Página SimbolosEquipo Personal de Protección Instrucciones DE SeguridadInstrucciones generales Uso intentado de la máquinaReabastecimiento Cabezal de Nylon Método de trabajoContragolpe Herramientas de CortePrimeros Auxilios Nunca rectificar o soldar las herramientas de corte dañadasEmbalaje EM4251/EM4251CA EM4250/EM4250CA Modelo Datos Técnicos EM4250/EM4250CA, EM4251/EM4251CAEM4250/EM4250CA Desbrozadora EM4251/EM4251CA Cortabordes Denominación DE PartesPara máquinas con manillar en U Montaje DEL ManillarPara máquinas con manillar cerrado USO DE Protector Para Hojas METALICAS/CORTADOR DE Cuerda Montaje DEL ProtectorPara EM4250/EM4250CA Para EM4250/EM4250CA, EM4251/EM4251CAPara EM4250/EM4250CA con la llave hexagonal todavía puesuta Montaje DE LA Hoja DE Corte O Cabezal DE Corte DE NylonMontaje de la cabeza de corte de nylon Inspección Y Reabastecimiento DE Aceite DE Motor Antes DE Empezar EL TrabajoPunto 1 de reabastecimiento de aceite bayoneta de aceite Almacenaje DE Lamáquinay Deltanque DE Reabastecimiento Reabastecimiento DE CombustiblePuntos Relacionados CON EL Manejo Y LA Parada USO Correcto DE LA MáquinaArranque Precauciones durante la operación Máquina con manillar U ó cerradoCuidado Afilar LA Herramienta DE CorteAjuste DEL Giro a Baja Velocidad Ralentí Arrancar después de la operación de calentamientoSustitución del cabezal de Nylon CabezaldenylonCambio DEL Aceite DEL Motor Instrucciones DE ServicioComprobación y mantenimiento diarios Puntos Relacionados CON EL Aceite Limpieza DEL Depurador DE AireManipulación del elemento del filtro de aire Cambio DE LA Tubería DE Combustible Comprobación DE LA BujiaSuministro DE Grasa a LA Caja DE Engranajes Limpieza DEL Filtro DE CombustibleAtención después de almacenamiento de largo tirmpo AlmacenamientoLocalizacion de averias Tiempo de Después Diaria-m Funcionamiento Iinvestigación DE Averías Page 11-8, Sumiyoshi-cho, Anjo, Aichi 446-8502, Japan
Related manuals
Manual 76 pages 44.63 Kb

EM5250CA, EM4250 specifications

The Makita EM4251CA and EM4250CA models are the latest additions to Makita's robust range of outdoor power equipment, specifically designed for professional landscapers and gardening enthusiasts. These brushcutters are known for their powerful performance, ease of use, and advanced technologies that enhance efficiency and durability.

The Makita EM4251CA features a displacement of 25.4cc, while the EM4250CA is slightly larger, with a 30.5cc engine. Both models are equipped with a high-performance 2-stroke engine that delivers impressive power and torque for tackling thick grass, weeds, and underbrush. The engines are designed for low emissions and fuel consumption, contributing to environmentally friendly operation while maintaining compliance with the latest regulatory standards.

One of the standout features of these brushcutters is the Easy Start System, which significantly reduces the effort required to start the engine. This system incorporates a spring-assisted starter that provides a smooth and reliable start every time. Additionally, the models offer a semi-automatic choke system that adjusts fuel flow for optimal performance in varying conditions.

For user comfort, the EM4251CA and EM4250CA are designed ergonomically, with a lightweight construction that enhances maneuverability without compromising strength. The adjustable bike handle provides solid control during operation, minimizing user fatigue during lengthy tasks. Both models also feature anti-vibration technology that reduces vibrations transmitted to the user, ensuring a more comfortable experience.

A robust and durable design is another hallmark of Makita's brushcutters. The fuel tank is constructed from high-quality materials to resist impacts and environmental factors, while the shaft is reinforced to withstand rigorous use. The inclusion of a reinforced cutter head allows for versatile cutting options, accommodating both trimmer line and metal blades for various applications.

For added convenience, these models are equipped with a soft grip handle that provides comfort during extended use, alongside a quick-release harness that allows for swift transitions between tasks. Overall, the Makita EM4251CA and EM4250CA brushcutters represent a blend of power, efficiency, and user-oriented design, making them ideal tools for anyone serious about maintaining their outdoor spaces.

With their mix of advanced technology and practical features, the EM4251 and EM4250 models ensure that users can tackle tough landscaping jobs with confidence and ease, making them invaluable assets for both professionals and hobbyists alike.
Top Page Image Contents