Makita UC 3000, UC 3500, UC 4000 Replacing the saw chain, Malfunction System Observation Cause

Page 16

Replacing the saw chain

CAUTION: Use only chains and guide bars designed for this saw (see the Extract from the spare parts list)!

A

1

B

Check the sprocket (A/1) before mounting a new chain.

The sprocket is located underneath the clutch drum (I/2).

CAUTION:

Worn out sprockets (B) may damage the new chain and must therefore be replaced.

Do not attempt to replace the sprocket yourself. Sprocket replacement requires special training and tools and must be done at a MAKITA service center.

Inspecting and replacing the carbon brushes

IMPORTANT:

Inspect the carbon brushes at regular intervals! A notch on the brush shows the limit of wear.

 

 

2

3

 

C

 

 

 

 

 

 

 

 

NOTE:

The carbon brush is very delicate, so be careful not to let it drop.

When taking it out, be sure to note the position it was installed in, since each brush is run in with the rotor.

-Use the combination wrench to unscrew the cover (C/2), and then pull out the brush (C/3).

-If the wear limit has not yet been reached, put the brush back in the same position and screw the cover (C/2) back on.

-Run the saw briefly (about a minute) so the brushes can run in again.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by MAKITA Authorized or Factory Service Centers, always using MAKITA replacement parts.

Troubleshooting

Malfunction

System

Observation

Cause

 

 

 

 

Chain saw does not work

total

electric motor does not function

no power supply,

 

 

 

cable defective

 

 

 

chain brake actuated

 

 

 

Mains fuse blown

insufficient performance

Carbon brushes

low pulling power

Carbon brushes worn down

no chain lubrication

Oil tank, oil pump

no oil on the saw chain

oil tank empty,

 

 

 

oil guide groove dirty

Chain brake

Brake

Saw chain does not stop instantly

Brake band worn down

 

 

 

 

16

Image 16
Contents Owner’s Safety Manual Thank you for your trust in our product Table of contentsPacking Symbols Delivery inventoryImportant Safety Instructions Read ALL Instructions Disconnect Chain Saw Outdoor Use Extension CordsStay Alert Check Damaged Parts Guard Against KickbackPower Supply Replacement PartsUse of Extension Cord Polarized PlugsChain Saw Nomenclature Mounting the guide bar and saw chain Putting Into OperationTightening the saw chain Chain brake maintenance Checking the chain tensionChain brake HintRefilling the oil tank Saw chain oilWaste oil Switching on the motor Holding the chain sawUsing the chain saw Checking the chain brakeChecking the chain lubrication Felling a treeFelling back cut Limbing a treeBucking a log Carrying toolMaintenance Files and how to work with themSharpening the saw chain 65 mm 025 MinCleaning the guide bar lubricating the sprocket nose Protective gloves must be wornInspecting and replacing the carbon brushes Replacing the saw chainMalfunction System Observation Cause Service, spare parts and guarantee Instructions for periodic maintenanceMaintenance and repair Spare partsExtract from the spare parts list GuaranteeAccessories Included in the delivery inventoryTechnical data Space for notesTravaux DE Maintenance Nous vous remercions pour votre confianceTable de matiè res EmballageLivraison complè te SymbolesAvertissement Utilisez les outils convenables Maintenez la zone de travail propre et rangé eTenez compte de l’environnement de travail Pré servez-vous des chocs é lectriquesDé branchez la tronç onneuse Vé rifiez les piè ces endommagé esUtilisation du cordon prolongateur Conservez Avec Soin CES InstructionsAlimentation é lectrique Piè ces dé taché esNomenclature des piè ces Dé taché es Tendre la chaîne de sciage Mise EN RouteMontage du guide-chaîne et de la chaîne Contrô le de la tension de la chaîne Frein de chaîneEntretien du frein de chaine et du frein de ralentissement Conseil PratiqueHuile de chaîne Huile Usagé eRemplir le ré servoir d’huile Mettre le moteur en marche Maintien de la tronç onneuseUtilisation de la tronç onneuse Encoche d’abattageRepli Longueurs d’arbreCoupe d’abattage EbranchageDé bitage Transport de l’outilAffû tage de la chaîne Travaux DE MaintenanceLime et guidage de la lime Nettoyer le guide-chaîne Regraisser l’é toile de dé viation Porter impé rativement des gants de protectionNouvelle chaîne de sciage Vé rifier / remplacer les balais de charbonRecherche de pannes Voir extrait de la liste de piè ces de rechangeEntretien et ré parations Instructions d’entretien et de maintenance pé riodiquesPiè ces de rechange Accessoires Extrait de la liste de piè ces de rechangeGarantie Livraison complè teCaracté ristiques techniques Ré servé e aux notesMakita U.S.A., Inc Makita Canada Inc

UC 3000, UC 3500, UC 4000 specifications

Makita, a leader in power tools, has developed a range of electric chainsaws designed for efficiency, power, and user comfort. Among these, the UC 3000, UC 3500, and UC 4000 models stand out, each offering unique features tailored to different cutting needs.

The Makita UC 3000 is an excellent choice for light to medium-duty tasks. It sports a 3000-watt motor, providing ample power for trimming branches, cutting firewood, and general garden maintenance. One of its key features is the tool-less chain tensioning system, which allows users to adjust the chain quickly and safely without the need for additional tools. The UC 3000 is equipped with an automatic chain lubrication system that ensures the chain runs smoothly and maintains optimal performance. Weighing relatively light, this model promotes user comfort and reduces fatigue during prolonged use.

Moving up in power, the Makita UC 3500 delivers a robust 3500-watt motor. This model is well-suited for more demanding jobs, such as cutting larger trees or heavy-duty landscaping tasks. The UC 3500 also features the tool-less chain tensioning system, providing an efficient and hassle-free experience. The automatic oiling mechanism continues to support the chain’s health, ensuring longevity and consistent performance. Additionally, the UC 3500 includes an ergonomic design with a comfortable grip to minimize vibrations, enhancing user control during operation and improving overall safety.

The UC 4000 takes power and performance to the next level, boasting a strong 4000-watt motor. This model is ideal for professional landscapers and those who regularly undertake heavy-duty cutting tasks. The UC 4000 combines the convenient tool-less chain tensioning system and automatic lubrication features found in its smaller counterparts but also incorporates advanced safety features such as a kickback brake. This ensures immediate chain stoppage if the chainsaw is used improperly, increasing user safety significantly. The lightweight design paired with an ergonomic handle makes this model manageable for extended periods while providing excellent balance.

In summary, the Makita UC 3000, UC 3500, and UC 4000 offer a versatile range of electric chainsaws suitable for various applications. Each model combines effective motors with user-friendly features and innovative technologies, ensuring that users can tackle cutting jobs with confidence and efficiency. Whether for casual gardening or professional landscaping, Makita's chainsaws are built to meet the demands of users at any skill level.