Makita DCS 400, DCS 401 manual Waste oil, Refuelling, Important note on bio-degradable chain oils

Page 21

We recommend the use of chain oil which is bio-degradable in order to protect the environment. The use of bio-degradable oil may even be required by local regulations.

The chain oil BIOTOP sold by MAKITA is made of special vegetable oils and is 100% bio-degradable. BIOTOP has been granted the "blue angel" (Blauer Umweltschutz-Engel) for being particularly environment-friendly (RAL UZ 48).

BIOTOP chain oil is available in the following sizes:

1 l order number 980 008 610

5 l order number 980 008 611

20 l order number 980 008 613

Bio-degradable oil is stable only for a limited period of time. It should be used within 2 years from the date of manufacture (printed on the container).

Important note on bio-degradable chain oils

If you are not planning to use the saw again for an extended period of time (longer than the expiration date of the chain oil), empty the oil tank and put in a small amount of regular engine oil (SAE 30),and then run the saw for a time. This is necessary to flush out all remaining bio-degradable oil from the oil tank, oil-feed system, chain and guide bar, as many such oils tend to leave sticky residues over time, which can cause damage to the oil pump or other parts.

The next time you use the saw, fill the tank with BIOTOP chain oil again.

waste oil

E

NEVER USE WASTE OIL

Waste oil is very dangerous for the environment.

Waste oil contains high amounts of carcinogenic substances.

Residues in waste oil result in a high degree of wear and tear at the oil pump and the sawing device.

In case of damage caused by using waste oil or unappropriate chain oil the product guarantee will be null and void.

Your salesman will inform you about the use of chain oil.

F

AVOID SKIN AND EYE CONTACT

Mineral oil products degrease your skin. If your skin comes in contact with these substances repeatedly and for an extended period of time, it will desiccate. Various skin deseases may result. In addition, allergic reactions are known to occur.

Eyes can be irritated by contact with oil. If oil comes into your eyes, immediately wash them with clear water.

If your eyes are still irritated, see a doctor immediately!

Refuelling

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

G

 

chain oil

 

 

fuel

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STOP

FOLLOW THE SAFETY PRECAUTIONS ON PAGE 7!

Be careful and cautious when handling fuels.

The engine must be switched off!

-Thoroughly clean the area around the plugs, to prevent dirt from getting into the fuel or oil tank.

-Unscrew the plug and fill the tank with fuel (fuel/oil mixture) or chain oil as the case may be. Fill up to the bottom edge of the filler neck. Be careful not to spill fuel or chain oil!

-Tightly screw on the plug.

Clean screw plug and tank after refuelling.

Lubricating the chain

During operation there must always be sufficient chain oil in the chain-oil tank to provide good chain lubrication. One filling is sufficient for about one half-hour of continuous operation.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Owner’s Safety Manual RE Y Makita DCS 340, DCS 341, DCS 400, DCS ContentsDelivery inventory SymbolsFurther SeeAdditional safety precautions Safety precautions for chain saw operatorsDiscription of symbols used on chain saws General Safety PrecautionsAnsi B175.1-1991 45M6Saw Proper clothingUse of the saw Transporting the chain sawFeet Chain saw operating instructionsFueling Fueling instructionsImportant adjustments Working conditionsCutting instructions Reactive forces during the cut, including kickback KickbackTo avoid kickback Saw chain cutter sharpnessSpeed of contact at which the cutter contacts the object Depth gaugesPushback Cutting techniquesTo avoid pushback To avoid pull-in= cutting down area Felling instructionsSectioning Method Plunge-Cut MethodBucking LimbingMaintaining and storing the saw Maintenance and RepairDenomination of components 13 12 Identification plate 15 14DCS Technical data DCS Approved bar and chain combinationsLength Mounting the guide bar and saw chain StopChecking the chain tension Tightening the saw chainFuel / Refuelling Safety chain brakeFuel mixture Chain oilWaste oil RefuellingImportant note on bio-degradable chain oils Stopping the engine Starting the engineCold start Warm startAdjusting the carburetor Checking the safety chain brakeSpeed Checking the chain lubricationWorking in winter 65 mm 025Sharpening the saw chain MinFiles and how to work with them Cleaning the guide bar, lubricating the sprocket noseProtective gloves must be worn Multi-purpose greaseReplacing / cleaning the spark arrester screen Cleaning the brake band and sprocket interiorReplacing the suction head Replacing the saw chainReplacing the spark plug Cleaning the air filterService, spare parts and guarantee Instructions for daily and periodic maintenanceMaintenance and repair Troubleshootig GuaranteeSpare parts Malfunction System Observation CauseDCS 400 / DCS Extract from the spare parts list DCS 340 / DCSMakita DCS 340, DCS 341, DCS 400, DCS Sommaire Etendue de la fourniture SymbolesAdditiounels VoirArrêtez le moteur avant de poser la tronçonneuse Mesures de sé curité supplé mentairesMesures gé né rales de sé curité Description des symboles figurant sur les tronç onneuses’utilisateur Condition physiqueLa tronç onneuse Quels vê tements porter?Utilisation de la tronç onneuse Transport de la tronç onneuseRavitaillement en carburant PiedsInstructions de ravitaillement Dé marrageRé glages importants Conditions de travailInstructions de coupe Choc de recul Kickback Affû tage des plaquettes de coupe de la chaîne Pour é viter le choc de reculLes limiteurs de profondeurs Le recul Techniques de coupePour é viter le recul Pour é viter la traction= zone d’abattage Instructions d’abattageMé thode de coupe en plongé e Mé thode de sectionnementDé bitage EbranchageEntretien et stockage de la tronç onneuse Entretien et ré parationDé signation des piè ces 13 12 Plaque signatique Caractéristiques techniques Combinaisons autorisé es de guides et de chaînesGuide 3/8 Longueur Ré fé renceMontage du rail-guide et de la chaîne de sciage Mise EN RouteStop Carburants/ravitaillement Frein de chaîneMé lange carburant Huile de chaîne de sciageRemplissage des ré servoirs Remarque importante pour les huiles de chaîne de sciage bioHuile Usagé e Arrê ter le moteur Dé marrer le moteurDé marrage à froid RemarqueVé rifier le frein de chaîne Ré glage du carburateurVé rifier le graissage de la chaîne Affû tage de la chaîne Marche hivernaleDe sciage Critè res d’affû tagePorter impé rativement des gants de protection Lime et guidage de la limeRemplacement de la cré pine d’aspiration Nouvelle chaîne de sciageChangement / nettoyage du pare-é tincelles Nettoyage du filtre d’air Remplacement de bougie StopNGK Bpmr 6F ou Vé rification de l’é tincelle d’allumageService d’atelier, piè ces de rechange et garantie Maintenance et ré parationsInstruction dentretien quotidien et pé riodique Garantie Piè ces de rechangeRecherche de pannes Panne Systè me Observation OrigineExtrait de la liste des piè ces de rechange DCS 340 / DCSDCS 400 / DCS Makita U.S.A., INC Makita Canada INC

DCS 400, DCS 341, DCS 401, DCS 340 specifications

Makita has been an industry leader in power tools, consistently delivering high-performance products that meet the needs of professionals and DIY enthusiasts alike. Among their impressive lineup of tools, the Makita DCS 340, DCS 401, DCS 341, and DCS 400 chainsaws stand out for their innovation, reliability, and ease of use. Each model offers unique features that cater to different applications and requirements.

The Makita DCS 340 is designed for versatility and efficiency. Equipped with a powerful 34cc engine, it provides ample power for a variety of cutting tasks. The lightweight design enhances maneuverability, making it an excellent choice for both professionals and home users. One of the key features of the DCS 340 is its advanced anti-vibration system, which reduces fatigue during extended use. The easy-start mechanism further enhances user experience, allowing for quick and hassle-free operation.

Next in line is the DCS 401, which boasts a 40cc engine, offering elevated power for more demanding applications. This model is particularly effective for heavy-duty cutting tasks such as felling larger trees and processing timber. The DCS 401 features a chain brake for improved safety, as well as an ergonomic handle that ensures a comfortable grip and enhanced control. The automatic chain oiling system also ensures consistent lubrication for smoother operation and extends the lifespan of the saw.

The DCS 341 model is similar to the DCS 340 but offers added convenience with its 40cc engine and a slightly different configuration tailored for more intricate work. It includes a tool-less chain adjustment feature, enabling quick and easy chain tension adjustments without additional tools. This model's lightweight design is further enhanced by its compact build, making it ideal for a variety of outdoor jobs like pruning and trimming.

Lastly, the Makita DCS 400 features a robust 40cc engine as well but is specifically designed for professional-grade performance. It excels in demanding environments, thanks to its durable construction and advanced air filtration system. This model significantly reduces wear and tear and increases longevity. The DCS 400 also offers a fast idle for easier cold starts and a transparent fuel tank, allowing for quick visual checks on fuel levels.

Overall, whether you're a professional or a hobbyist, the DCS series from Makita provides reliable, powerful, and user-friendly options for all your cutting needs. Each model is designed with safety, comfort, and efficiency in mind, ensuring that you can tackle any project with confidence.
Top Page Image Contents