Makita DCS 400 manual Cleaning the guide bar, lubricating the sprocket nose, Multi-purpose grease

Page 25

E

-All cutters must be sharpened to the same angle, 30°. Different angles result in a roughly, irregularly running chain, increase wear and tear and cause chain breakage.

-The 85° front rake of the cutter results from the cut depth of the round file. If the proper file is used in the right manner, the correct front rake will be obtained automatically.

F

Files and how to work with them

- Use a special round file for chains (dia. 4 mm) for sharpe- ning the chain. Normal round files are not appropriate for this work. See "Accessories" for the order number.

-The file should cut only when pushed forwards (arrow). Lift the file when leading it backwards.

-First sharpen the shortest cutter. The length of this cutter is then the standerd for all other cutters of the chain.

-Always guide the file horizontally (90o to the guide bar).

4/5

30°

G

-The file holder makes file guidance easier. It is marked for the correct 30° sharpening angle (keep the marks parallel with the chain when filing, see illustration) and limits the cut depth to the correct 4/5 of the file diameter. See "Accesso- ries" for the order number.

H

I

-After having sharpened the chain, the height of the depth limiter must be checked by means of a chain gauge. See "Accessories" for the order number.

-Correct even the smallest excess height with a special flat file (H). See "Accessories" for the order number.

-Round off the front of the depth limiter (I).

Cleaning the guide bar, lubricating the sprocket nose

CAUTION:

Protective gloves must be worn.

J

Regularly inspect the bearing surfaces of the guide bar for damage, and clean them with a suitable tool.

If the saw is used intensively it will be necessary to lubricate the return sprocket bearings regularly (once a week). To do this, first thoroughly clean the 2 mm hole at the tip of the guide bar, and then press in a small amount of multi-purpose grease.

Multi-purpose grease and grease guns are available as accessories.

Multi-purpose grease

(order no. 944 360 000)

Grease gun

(order no. 944 350 000)

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Owner’s Safety Manual RE Y Makita DCS 340, DCS 341, DCS 400, DCS ContentsDelivery inventory SymbolsFurther SeeAdditional safety precautions Safety precautions for chain saw operatorsDiscription of symbols used on chain saws General Safety PrecautionsAnsi B175.1-1991 45M6Saw Proper clothingUse of the saw Transporting the chain sawFeet Chain saw operating instructionsFueling Fueling instructionsWorking conditions Important adjustmentsCutting instructions Reactive forces during the cut, including kickback KickbackTo avoid kickback Saw chain cutter sharpnessSpeed of contact at which the cutter contacts the object Depth gaugesPushback Cutting techniquesTo avoid pushback To avoid pull-in= cutting down area Felling instructionsSectioning Method Plunge-Cut MethodBucking LimbingMaintaining and storing the saw Maintenance and Repair15 14 Denomination of components 13 12 Identification plateDCS Approved bar and chain combinations Technical data DCSLength Mounting the guide bar and saw chain StopChecking the chain tension Tightening the saw chainFuel / Refuelling Safety chain brakeFuel mixture Chain oilRefuelling Waste oilImportant note on bio-degradable chain oils Stopping the engine Starting the engineCold start Warm startAdjusting the carburetor Checking the safety chain brakeSpeed Checking the chain lubricationWorking in winter 65 mm 025Sharpening the saw chain MinFiles and how to work with them Cleaning the guide bar, lubricating the sprocket noseProtective gloves must be worn Multi-purpose greaseReplacing / cleaning the spark arrester screen Cleaning the brake band and sprocket interiorReplacing the suction head Replacing the saw chainReplacing the spark plug Cleaning the air filterInstructions for daily and periodic maintenance Service, spare parts and guaranteeMaintenance and repair Troubleshootig GuaranteeSpare parts Malfunction System Observation CauseDCS 400 / DCS Extract from the spare parts list DCS 340 / DCSMakita DCS 340, DCS 341, DCS 400, DCS Sommaire Etendue de la fourniture SymbolesAdditiounels VoirArrêtez le moteur avant de poser la tronçonneuse Mesures de sé curité supplé mentairesMesures gé né rales de sé curité Description des symboles figurant sur les tronç onneuses’utilisateur Condition physiqueLa tronç onneuse Quels vê tements porter?Utilisation de la tronç onneuse Transport de la tronç onneuseRavitaillement en carburant PiedsInstructions de ravitaillement Dé marrageConditions de travail Ré glages importantsInstructions de coupe Choc de recul Kickback Pour é viter le choc de recul Affû tage des plaquettes de coupe de la chaîneLes limiteurs de profondeurs Le recul Techniques de coupePour é viter le recul Pour é viter la traction= zone d’abattage Instructions d’abattageMé thode de coupe en plongé e Mé thode de sectionnementDé bitage EbranchageEntretien et stockage de la tronç onneuse Entretien et ré parationDé signation des piè ces 13 12 Plaque signatique Caractéristiques techniques Combinaisons autorisé es de guides et de chaînesGuide 3/8 Longueur Ré fé renceMontage du rail-guide et de la chaîne de sciage Mise EN RouteStop Carburants/ravitaillement Frein de chaîneMé lange carburant Huile de chaîne de sciageRemarque importante pour les huiles de chaîne de sciage bio Remplissage des ré servoirsHuile Usagé e Arrê ter le moteur Dé marrer le moteurDé marrage à froid RemarqueRé glage du carburateur Vé rifier le frein de chaîneVé rifier le graissage de la chaîne Affû tage de la chaîne Marche hivernaleDe sciage Critè res d’affû tagePorter impé rativement des gants de protection Lime et guidage de la limeNouvelle chaîne de sciage Remplacement de la cré pine d’aspirationChangement / nettoyage du pare-é tincelles Nettoyage du filtre d’air Remplacement de bougie StopNGK Bpmr 6F ou Vé rification de l’é tincelle d’allumageMaintenance et ré parations Service d’atelier, piè ces de rechange et garantieInstruction dentretien quotidien et pé riodique Garantie Piè ces de rechangeRecherche de pannes Panne Systè me Observation OrigineDCS 340 / DCS Extrait de la liste des piè ces de rechangeDCS 400 / DCS Makita U.S.A., INC Makita Canada INC

DCS 400, DCS 341, DCS 401, DCS 340 specifications

Makita has been an industry leader in power tools, consistently delivering high-performance products that meet the needs of professionals and DIY enthusiasts alike. Among their impressive lineup of tools, the Makita DCS 340, DCS 401, DCS 341, and DCS 400 chainsaws stand out for their innovation, reliability, and ease of use. Each model offers unique features that cater to different applications and requirements.

The Makita DCS 340 is designed for versatility and efficiency. Equipped with a powerful 34cc engine, it provides ample power for a variety of cutting tasks. The lightweight design enhances maneuverability, making it an excellent choice for both professionals and home users. One of the key features of the DCS 340 is its advanced anti-vibration system, which reduces fatigue during extended use. The easy-start mechanism further enhances user experience, allowing for quick and hassle-free operation.

Next in line is the DCS 401, which boasts a 40cc engine, offering elevated power for more demanding applications. This model is particularly effective for heavy-duty cutting tasks such as felling larger trees and processing timber. The DCS 401 features a chain brake for improved safety, as well as an ergonomic handle that ensures a comfortable grip and enhanced control. The automatic chain oiling system also ensures consistent lubrication for smoother operation and extends the lifespan of the saw.

The DCS 341 model is similar to the DCS 340 but offers added convenience with its 40cc engine and a slightly different configuration tailored for more intricate work. It includes a tool-less chain adjustment feature, enabling quick and easy chain tension adjustments without additional tools. This model's lightweight design is further enhanced by its compact build, making it ideal for a variety of outdoor jobs like pruning and trimming.

Lastly, the Makita DCS 400 features a robust 40cc engine as well but is specifically designed for professional-grade performance. It excels in demanding environments, thanks to its durable construction and advanced air filtration system. This model significantly reduces wear and tear and increases longevity. The DCS 400 also offers a fast idle for easier cold starts and a transparent fuel tank, allowing for quick visual checks on fuel levels.

Overall, whether you're a professional or a hobbyist, the DCS series from Makita provides reliable, powerful, and user-friendly options for all your cutting needs. Each model is designed with safety, comfort, and efficiency in mind, ensuring that you can tackle any project with confidence.
Top Page Image Contents