Makita DCS 340, DCS 401, DCS 400, DCS 341 manual Stop, Mounting the guide bar and saw chain

Page 18

PUTTING INTO OPERATION

STOP

Mounting the guide bar and saw chain

Use the universal wrench delivered with the chain saw for the following work.

Put the chain saw on a stable surface and carry out the following steps for mounting the guide bar and chain:

CAUTION: Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Always wear protective gloves!

CAUTION: Start the chain saw only after having assem- bled it completely and inspected!

2

1

A

-Release the chain brake by pulling the hand guard (A/1) towards the tubular handle (A/2) until you feel it catch.

4

3

B

-Unscrew retaining nut (B/3).

-Pull off the sprocket guard (B/4).

6

C

7

 

- Turn the chain adjusting screw (C/6) to the left (counter- clockwise) until the pin (C/7) is at the left stop.

8

9

D

-Position the guide bar (D/8). Make sure that the pin (D/9) of the chain tightener is in the hole (circled) on the guide bar.

E

10 8

11

10 12

F

-Lift the chain (E/10) over the clutch drum and onto the sprocket (E/11). Using your right hand, guide the chain into the top guide groove on the guide bar (E/8).

NOTE: The cutting edges along the top of the chain must point in the direction of the arrow!

-Lead the chain (F/10) around the sprocket nose (F/12) of the guide bar.

NOTE: The chain should be easy to pull in the direction of the arrow. The clutch drum (E/11) should turn with the chain (the sprocket engages the chain).

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Owner’s Safety Manual Makita DCS 340, DCS 341, DCS 400, DCS Contents RE YFurther SymbolsDelivery inventory SeeSafety precautions for chain saw operators Additional safety precautionsAnsi B175.1-1991 General Safety PrecautionsDiscription of symbols used on chain saws 45M6Use of the saw Proper clothingSaw Transporting the chain sawFueling Chain saw operating instructionsFeet Fueling instructionsImportant adjustments Working conditionsCutting instructions Kickback Reactive forces during the cut, including kickbackSpeed of contact at which the cutter contacts the object Saw chain cutter sharpnessTo avoid kickback Depth gaugesTo avoid pushback Cutting techniquesPushback To avoid pull-inFelling instructions = cutting down areaPlunge-Cut Method Sectioning MethodLimbing BuckingMaintenance and Repair Maintaining and storing the sawDenomination of components 13 12 Identification plate 15 14DCS Technical data DCS Approved bar and chain combinationsLength Stop Mounting the guide bar and saw chainTightening the saw chain Checking the chain tensionFuel mixture Safety chain brakeFuel / Refuelling Chain oilWaste oil RefuellingImportant note on bio-degradable chain oils Cold start Starting the engineStopping the engine Warm startSpeed Checking the safety chain brakeAdjusting the carburetor Checking the chain lubricationSharpening the saw chain 65 mm 025Working in winter MinProtective gloves must be worn Cleaning the guide bar, lubricating the sprocket noseFiles and how to work with them Multi-purpose greaseReplacing the suction head Cleaning the brake band and sprocket interiorReplacing / cleaning the spark arrester screen Replacing the saw chainCleaning the air filter Replacing the spark plugService, spare parts and guarantee Instructions for daily and periodic maintenanceMaintenance and repair Spare parts GuaranteeTroubleshootig Malfunction System Observation CauseExtract from the spare parts list DCS 340 / DCS DCS 400 / DCSMakita DCS 340, DCS 341, DCS 400, DCS Sommaire Additiounels SymbolesEtendue de la fourniture VoirMesures de sé curité supplé mentaires Arrêtez le moteur avant de poser la tronçonneuse’utilisateur Description des symboles figurant sur les tronç onneusesMesures gé né rales de sé curité Condition physiqueUtilisation de la tronç onneuse Quels vê tements porter?La tronç onneuse Transport de la tronç onneuseInstructions de ravitaillement PiedsRavitaillement en carburant Dé marrageRé glages importants Conditions de travailInstructions de coupe Choc de recul Kickback Affû tage des plaquettes de coupe de la chaîne Pour é viter le choc de reculLes limiteurs de profondeurs Pour é viter le recul Techniques de coupeLe recul Pour é viter la tractionInstructions d’abattage = zone d’abattageMé thode de sectionnement Mé thode de coupe en plongé eEbranchage Dé bitageEntretien et ré paration Entretien et stockage de la tronç onneuseDé signation des piè ces 13 12 Plaque signatique Guide 3/8 Combinaisons autorisé es de guides et de chaînesCaractéristiques techniques Longueur Ré fé renceMise EN Route Montage du rail-guide et de la chaîne de sciageStop Mé lange carburant Frein de chaîneCarburants/ravitaillement Huile de chaîne de sciageRemplissage des ré servoirs Remarque importante pour les huiles de chaîne de sciage bioHuile Usagé e Dé marrage à froid Dé marrer le moteurArrê ter le moteur RemarqueVé rifier le frein de chaîne Ré glage du carburateurVé rifier le graissage de la chaîne De sciage Marche hivernaleAffû tage de la chaîne Critè res d’affû tageLime et guidage de la lime Porter impé rativement des gants de protectionRemplacement de la cré pine d’aspiration Nouvelle chaîne de sciageChangement / nettoyage du pare-é tincelles NGK Bpmr 6F ou Remplacement de bougie StopNettoyage du filtre d’air Vé rification de l’é tincelle d’allumageService d’atelier, piè ces de rechange et garantie Maintenance et ré parationsInstruction dentretien quotidien et pé riodique Recherche de pannes Piè ces de rechangeGarantie Panne Systè me Observation OrigineExtrait de la liste des piè ces de rechange DCS 340 / DCSDCS 400 / DCS Makita U.S.A., INC Makita Canada INC

DCS 400, DCS 341, DCS 401, DCS 340 specifications

Makita has been an industry leader in power tools, consistently delivering high-performance products that meet the needs of professionals and DIY enthusiasts alike. Among their impressive lineup of tools, the Makita DCS 340, DCS 401, DCS 341, and DCS 400 chainsaws stand out for their innovation, reliability, and ease of use. Each model offers unique features that cater to different applications and requirements.

The Makita DCS 340 is designed for versatility and efficiency. Equipped with a powerful 34cc engine, it provides ample power for a variety of cutting tasks. The lightweight design enhances maneuverability, making it an excellent choice for both professionals and home users. One of the key features of the DCS 340 is its advanced anti-vibration system, which reduces fatigue during extended use. The easy-start mechanism further enhances user experience, allowing for quick and hassle-free operation.

Next in line is the DCS 401, which boasts a 40cc engine, offering elevated power for more demanding applications. This model is particularly effective for heavy-duty cutting tasks such as felling larger trees and processing timber. The DCS 401 features a chain brake for improved safety, as well as an ergonomic handle that ensures a comfortable grip and enhanced control. The automatic chain oiling system also ensures consistent lubrication for smoother operation and extends the lifespan of the saw.

The DCS 341 model is similar to the DCS 340 but offers added convenience with its 40cc engine and a slightly different configuration tailored for more intricate work. It includes a tool-less chain adjustment feature, enabling quick and easy chain tension adjustments without additional tools. This model's lightweight design is further enhanced by its compact build, making it ideal for a variety of outdoor jobs like pruning and trimming.

Lastly, the Makita DCS 400 features a robust 40cc engine as well but is specifically designed for professional-grade performance. It excels in demanding environments, thanks to its durable construction and advanced air filtration system. This model significantly reduces wear and tear and increases longevity. The DCS 400 also offers a fast idle for easier cold starts and a transparent fuel tank, allowing for quick visual checks on fuel levels.

Overall, whether you're a professional or a hobbyist, the DCS series from Makita provides reliable, powerful, and user-friendly options for all your cutting needs. Each model is designed with safety, comfort, and efficiency in mind, ensuring that you can tackle any project with confidence.
Top Page Image Contents