Husqvarna 327HDA65X, 327HE3X, 327HE4X manual Maintenance schedule, Maintenance Daily Weekly Monthly

Page 23

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by an authorized service workshop.

Maintenance

Daily

 

Weekly

Monthly

maintenance

maintenance

maintenance

 

 

 

 

 

 

Clean the outside of the machine.

 

X

 

 

 

 

 

 

 

Make sure the throttle trigger lock and the throttle function correctly

 

X

 

 

from a safety point of view.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the stop switch works correctly.

 

X

 

 

 

 

 

 

 

Check that the blades do not move when the engine is idling or

 

X

 

 

when the choke is in the start throttle position.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the blades are undamaged and show no signs of

 

X

 

 

cracking or other damage. Replace the blades if necessary.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the blade guard is not damaged or distorted. Replace

 

X

 

 

the blade guard if it is bent or damaged. (327HDA65)

 

 

 

 

 

 

 

 

 

 

 

 

Clean the air filter. Replace if necessary.

 

X

 

 

 

 

 

 

 

Check that the hand guard is not damaged. Replace the guard if

 

X

 

 

damaged. (327HDA65, 327HE3)

 

 

 

 

 

 

 

 

 

 

 

 

Check that nuts and screws are tight.

 

X

 

 

 

 

 

 

 

Check that there are no fuel leaks from the engine, tank or fuel lines.

 

X

 

 

 

 

 

 

 

Check the starter and starter cord.

 

 

X

 

 

 

 

 

 

Check that the vibration damping elements are not damaged.

 

 

X

 

 

 

 

 

 

Clean the outside of the spark plug. Remove it and check the

 

 

 

 

electrode gap. Adjust the gap to 0.5 mm or replace the spark plug.

 

 

X

 

Check that the spark plug is fitted with a suppressor.

 

 

 

 

 

 

 

 

 

Clean the machine’s cooling system.

 

 

X

 

 

 

 

 

 

Clean or replace the spark arrestor mesh on the muffler (only

 

 

X

 

applies to mufflers without a catalytic converter).

 

 

 

 

 

 

 

 

 

 

 

 

Clean the outside of the carburettor and the space around it.

 

 

X

 

 

 

 

 

 

Fill the gear housing with grease. This should be carried out

 

 

X

 

approximately every 60 working hours.

 

 

 

 

 

 

 

 

 

 

 

 

Check that the screws that hold the blades together are correctly

 

 

X

 

tightened.

 

 

 

 

 

 

 

 

 

 

 

 

Clean the fuel tank.

 

 

 

X

 

 

 

 

 

Check the fuel filter from contamination and the fuel hose from

 

 

 

X

cracks or other defects. Replace if necessary.

 

 

 

 

 

 

 

 

 

 

 

 

Check all cables and connections.

 

 

 

X

 

 

 

 

 

Check the clutch, clutch springs and the clutch drum for wear.

 

 

 

X

Replace if necessary by an autorized service workshop.

 

 

 

 

 

 

 

 

 

 

 

 

Replace the spark plug. Check that the spark plug is fitted with a

 

 

 

X

suppressor.

 

 

 

 

 

 

 

 

 

 

 

 

Check and clean the spark arrestor mesh on the muffler (only

 

 

 

X

applies to mufflers fitted with a catalytic converter).

 

 

 

 

 

 

 

 

 

 

 

 

To reduce the fire hazard, clean dirt, leaves and surplus lubricant,

 

 

 

X

etc from the muffler and engine.

 

 

 

 

 

 

 

 

 

 

 

 

English – 23

Image 23
Contents English 327HDA65X-seriesSymbols KEY to SymbolsContents Dear Customer IntroductionWhat is what? What is WHAT?Personal protective equipment General Safety PrecautionsThrottle lockout Machine′s safety equipmentMuffler Stop switchHand guard Vibration damping system327HDA65 Gear housingBlades Blade guardFitting the cutting head AssemblyFitting the hand guard and loop handle Fitting the handle327HE4 Adjusting the harnessFitting the impact guard Fuel Fuel safetyFuel Handling Mixing FuellingStarting Starting and StoppingCheck before starting Starting and stoppingStopping General working instructions Safety instructions regarding the surroundingsSafety instructions while working Working TechniquesChanging the hedge trimmer angle Safety instructions after completing workBasic working techniques Transport position Muffler MaintenanceCarburettor Spark plug Cooling systemOiling the air filter Gear housingCleaning the air filter Air filterCleaning and lubrication Maintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataEC-declaration of conformity Applies to Europe only Page Page 1151377-26