Snapper RP216019KWV, RP2167519B, RP217019BVE Service After First 5 Hours 3.2.1. Change Engine OIL

Page 11

Section 3 – MAINTENANCE

3.1INTRODUCTION

To retain the quality of the mower, use genuine SNAPPER replacement parts only. Contact a local SNAPPER dealer for parts and service assistance. For the correct part or information for a particular mower, always mention model and serial number.

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

3.2SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OIL

IMPORTANT: Drain fuel tank before tipping machine. DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

1.Refer to Engine Manual for proper oil specifications, procedures and proper service intervals.

2.For simplest/cleanest oil change, loosen lower handle nuts and fold handles. Stand mower up on lower handle brackets as shown in Figure 3.1. Drain oil through dipstick tube into a container. Allow sufficient time for all oil to drain. NOTE: Drive control rod on self-propelled models prohibits handles from folding. Simply tip mower on its side to drain oil.

FIGURE 3.1

3.Dispose of drain oil properly.

4.Fill engine with oil as specified in Engine Manual. Do Not overfill.

NOTE: Check specific model engine owner’s manual for changing engine oil procedure and oil specifications.

3.2.2.CHECK GREASE LEVEL IN TRANSMISSION 1. Remove transmission fill plug. Roll machine forward or backward while looking down into plug hole.

2. If liquid grease IS NOT visible on the input gear (the small gear below the plug hole), add an amount, to cover gear, of Snapper “00” grease. See Figure 3.2.

FILL PLUG

FIGURE 3.2

NOTE: Snapper “00” Grease (Part No. 7029443) is available at your SNAPPER dealer.

NOTE: Do not spill grease or oil on surface of drive disc. See Figure 3.3.

3.Reinstall transmission plug.

4.Check grease level after each 25 hours of operation.

KEEP DRIVE DISC CLEAN !

FIGURE 3.3

IMPORTANT: Drain fuel tank before tipping mower.

DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents TP 100-5087-IR-WB-N Engine OptionEngine Designation Series DesignationImportant Safety Instructions From Previous Column From PreviousDo not refuel the machine indoors Important Safety Instructions Table of Contents Nomenclature Briggs Engine Speed KawasakiControl IntroductionEngine & Blade Briggs Engine PRE-START Check ListStarting & Operation Propelling Mower Handle Height AdjustmentCutting Height Adjustment StoppingTo Raise Recycling Cover Installation of Side Discharge DeflectorRecycling Operation Installation of Grass BAG Door Type Bag Important Drain fuel tank before tipping mower Service After First 5 Hours 3.2.1. Change Engine OILDispose of drain oil properly Check Engine Drive Belt Service AnnuallyStorage Procedure Check Mower Blade1.A. Ninja Blade Wear Limit Mower Blade Replacement Standard Blade Wear LimitBlade Sharpening Wheel Drive Control Adjustment Driven Disc Adjustment Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementOn Next Replacing Rubber Driven Disc Repair & Adjustments On Next Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Pulley Position Reinstall blade hub and cutter bladeBattery Service 1. Remove battery Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery TestingCorrective Action Problem Probable CauseUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts 100Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page Steel Deck Recycling Walk Mowers Series

RP216019KWV, RP217019BV, RP217019BVE, RP2167519B specifications

The Snapper RP2167519B, RP217019BV, RP217019BVE, and RP216019KWV are standout models in Snapper's line of riding lawn mowers, designed for homeowners seeking efficiency, durability, and performance. Each model showcases a blend of innovative technologies and thoughtful engineering, making them suitable for various lawn care needs.

The RP2167519B features a robust 42-inch cutting deck powered by a reliable and efficient engine. This model comes equipped with a hydrostatic transmission, which allows for smooth acceleration and easy maneuverability, enabling users to tackle large lawns with ease. Its compact design makes it ideal for fitting into smaller spaces, while the adjustable cutting height gives users the flexibility to maintain their grass at the desired length.

The RP217019BV is another excellent option that boasts a powerful 19.5 HP engine. This model is equipped with a high-performance gear drive, providing users with enhanced control and responsiveness. The 42-inch deck is complemented by a side discharge feature, efficiently dispersing grass clippings while mowing. Furthermore, the ergonomic seating and user-friendly controls ensure comfort during extended use, making lawn care a more pleasant experience.

For those looking for added versatility, the RP217019BVE is a standout model with enhanced features. Similar in build to the RP217019BV, this variant introduces electric start technology, eliminating the need for manual pulling and simplifying the start-up process. The model incorporates a sturdy frame and premium materials, ensuring longevity and resilience over years of regular use. A mulching kit can also be easily added, offering users different options for maintaining their lawns.

Lastly, the RP216019KWV offers a unique combination of power and efficiency in a compact design. Featuring a 19 HP engine, this model is designed to operate quietly while delivering excellent cutting performance. Its easy-to-use controls and superior maneuverability make it a fantastic choice for homeowners with intricate landscaping. The model’s maintenance-free transmission is another highlight, as it requires less upkeep compared to traditional gear systems.

In summary, the Snapper RP2167519B, RP217019BV, RP217019BVE, and RP216019KWV provide users with reliable options tailored to various mowing needs. With their powerful engines, versatile features, and user-friendly designs, these riding mowers stand out as excellent investments for efficient lawn care. Whether for efficiency, comfort, or performance, Snapper consistently delivers quality in their riding lawn mowers.
Top Page Image Contents