Snapper RP2167519B, RP217019BVE, RP216019KWV Wheel Drive Control Adjustment

Page 14

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.Sharpen blade on a grinding wheel at an angle of

22to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.4.

DO NOT SHARPEN

 

BEYOND ORIGINAL

 

CUTTING EDGE

22-28º

 

BLADE TIP

END VIEW OF

BLADE ASSEMBLY

ORIGINAL CUTTING EDGE

FIGURE 4.4

5.Check blade for balance. If necessary, correct balance by grinding heavy end of blade.

6.Reinstall blade. See Figure 4.3. Check torque of blade retaining cap screw. Recommended torque should be 40 ft. lbs.

NOTE: The following sections 4.2 through 4.4 are for self-propelled models only.

4.2WHEEL DRIVE CONTROL ADJUSTMENT

1. The wheel drive control is properly adjusted when there is 1/16” to 1/8” clearance between the inside of the spring hook and the inside of the clutch cable eye with the wheel drive control released. See Figure 4.5.

CLUTCH CABLE

 

VINYL SPRING

 

1/16” TO 1/8”

CLUTCH CABLE

CLEARANCE

EYE

UPPER

 

SPRING

SPRING HOOK

 

LOWER

 

SPRING

 

CABLE

CLUTCH CABLE EYE

SPRING

FIGURE 4.5

2.To adjust, unhook upper spring from cable eye and rotate spring in direction required to extend or shorten spring length.

3.Rehook upper spring to cable eye and check clearance. Repeat procedure if required.

NOTE: The vinyl spring cover should be kept over the spring at all times except for adjustments.

4.If the wheel drive control fails to return quickly to the “OFF” position when released, check for binding at the cable holdings located on the side of the right handle. The upper clip should be located 2” below the upper knob; the lower clip should be 4” above the lower knob. The cable should slide freely with the clips installed at these locations.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Series Designation Engine OptionEngine Designation TP 100-5087-IR-WB-NImportant Safety Instructions From Previous Column From PreviousDo not refuel the machine indoors Important Safety Instructions Table of Contents Introduction Briggs Engine Speed KawasakiControl NomenclatureEngine & Blade Briggs Engine PRE-START Check ListStarting & Operation Stopping Handle Height AdjustmentCutting Height Adjustment Propelling MowerTo Raise Recycling Cover Installation of Side Discharge DeflectorRecycling Operation Installation of Grass BAG Door Type Bag Important Drain fuel tank before tipping mower Service After First 5 Hours 3.2.1. Change Engine OILDispose of drain oil properly Check Mower Blade Service AnnuallyStorage Procedure Check Engine Drive Belt1.A. Ninja Blade Wear Limit Mower Blade Replacement Standard Blade Wear LimitBlade Sharpening Wheel Drive Control Adjustment Drive Spring Repair/Replacement Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments On Next Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Reinstall blade hub and cutter blade Pulley PositionBattery Testing Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery Service 1. Remove batteryProblem Probable Cause Corrective Action100 Service Performed EachMAINTENANCE/REPLACEMENT Parts USE HRS SeasonYear Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page Steel Deck Recycling Walk Mowers Series

RP216019KWV, RP217019BV, RP217019BVE, RP2167519B specifications

The Snapper RP2167519B, RP217019BV, RP217019BVE, and RP216019KWV are standout models in Snapper's line of riding lawn mowers, designed for homeowners seeking efficiency, durability, and performance. Each model showcases a blend of innovative technologies and thoughtful engineering, making them suitable for various lawn care needs.

The RP2167519B features a robust 42-inch cutting deck powered by a reliable and efficient engine. This model comes equipped with a hydrostatic transmission, which allows for smooth acceleration and easy maneuverability, enabling users to tackle large lawns with ease. Its compact design makes it ideal for fitting into smaller spaces, while the adjustable cutting height gives users the flexibility to maintain their grass at the desired length.

The RP217019BV is another excellent option that boasts a powerful 19.5 HP engine. This model is equipped with a high-performance gear drive, providing users with enhanced control and responsiveness. The 42-inch deck is complemented by a side discharge feature, efficiently dispersing grass clippings while mowing. Furthermore, the ergonomic seating and user-friendly controls ensure comfort during extended use, making lawn care a more pleasant experience.

For those looking for added versatility, the RP217019BVE is a standout model with enhanced features. Similar in build to the RP217019BV, this variant introduces electric start technology, eliminating the need for manual pulling and simplifying the start-up process. The model incorporates a sturdy frame and premium materials, ensuring longevity and resilience over years of regular use. A mulching kit can also be easily added, offering users different options for maintaining their lawns.

Lastly, the RP216019KWV offers a unique combination of power and efficiency in a compact design. Featuring a 19 HP engine, this model is designed to operate quietly while delivering excellent cutting performance. Its easy-to-use controls and superior maneuverability make it a fantastic choice for homeowners with intricate landscaping. The model’s maintenance-free transmission is another highlight, as it requires less upkeep compared to traditional gear systems.

In summary, the Snapper RP2167519B, RP217019BV, RP217019BVE, and RP216019KWV provide users with reliable options tailored to various mowing needs. With their powerful engines, versatile features, and user-friendly designs, these riding mowers stand out as excellent investments for efficient lawn care. Whether for efficiency, comfort, or performance, Snapper consistently delivers quality in their riding lawn mowers.
Top Page Image Contents