Snapper RP217019BVE, RP2167519B Recycling Operation, Installation of Side Discharge Deflector

Page 9

Section 2 - OPERATING INSTRUCTIONS

2.Set all wheels at the same cutting height. The highest cutting position is Notch 7. The lowest cutting position is Notch 1. See Figures 2.8 & 2.9.

LATCH

POSITION

CUTTING HEIGHT SETTINGS

FIGURE 2.9

2.6 RECYCLING OPERATION

NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.

Set all wheels in the highest cutting position (Notch

7). Refer to Section “Cutting Height Adjustment”.

2.

Move engine speed control to “FAST” (Rabbit)

position.

3.

Move ground speed control to slowest speed

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

2.7INSTALLATION OF SIDE DISCHARGE DEFLECTOR

STEP 1: Raise recycling cover. Refer to Section “Recycling Operation”.

STEP 2: Install deflector to deck underneath raised

recycling cover, making sure that: 1) outside front edge of deflector slips behind recycling cover hinge bracket, 2) slot on inside front of deflector slips under restraining nut on top of deck (under right front corner of engine), and 3) slot on inside rear of deflector slips onto stud behind rear of discharge opening, where rear of recycling cover was originally secured. See Figure 2.11. Install internal/external tooth lock washer and knob nut onto stud and tighten securely. Release recycling cover and allow it to rest against side discharge deflector.

setting.

4. Proceed mowing slowly. If grass is very dense,

lower each rear wheel latch one notch lower than the

front wheel latches to improve recycling performance.

NOTE: The recycling cover is designed to remain on the machine at all times. When alternate discharge operations are desired, such as side discharging or bagging, recycling cover can be raised to accommodate alternate discharge components.

TO RAISE RECYCLING COVER:

Remove knob nut and internal/external tooth lock washer securing rear of recycling cover to mower deck. Pull rear of cover out from stud, and flip cover forward. See Figure 2.10.

FRONT

SLOT

REAR SLOT UNDER NUT OVER STUD ;

INSTALL LOCK WASHER & KNOB NUT

FIGURE 2.11

RECYCLING COVER (RAISED)

FRONT

EDGE

BEHIND

HINGE

BRACKET

PULL REAR OF

 

SPRING-

RECYCLING

 

LOADED

COVER OUT FROM

 

HINGE

STUD, AND FLIP

 

 

 

 

COVER FORWARD

 

 

 

 

 

REMOVE KNOB NUT & LOCK WASHER

FIGURE 2.10

2.8INSTALLATION OF GRASS BAG ADAPTER (Optional Accessory on Some Models)

STEP 1: Raise recycling cover. Refer to Section “Recycling Operation”.

STEP 2: Install grass bag adapter to deck in place of

raised recycling cover, making sure that: 1) outside front edge of adapter slips behind recycling cover hinge bracket, 2) slot on inside front of adapter slips under restraining nut on top of deck (under right front corner of engine), and 3) slot on bottom rear of adapter slips onto stud behind rear of discharge opening, where rear of recycling cover was originally secured. See Figure 2.12. Install internal/external tooth lock washer and knob nut onto stud and tighten securely. Release recycling cover and allow it to rest against adapter.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Engine Designation Engine OptionSeries Designation TP 100-5087-IR-WB-NImportant Safety Instructions From Previous Do not refuel the machine indoorsFrom Previous Column Important Safety Instructions Table of Contents Control Briggs Engine Speed KawasakiIntroduction NomenclaturePRE-START Check List Starting & OperationEngine & Blade Briggs Engine Cutting Height Adjustment Handle Height AdjustmentStopping Propelling MowerInstallation of Side Discharge Deflector Recycling OperationTo Raise Recycling Cover Installation of Grass BAG Door Type Bag Service After First 5 Hours 3.2.1. Change Engine OIL Dispose of drain oil properlyImportant Drain fuel tank before tipping mower Storage Procedure Service AnnuallyCheck Mower Blade Check Engine Drive BeltMower Blade Replacement Standard Blade Wear Limit Blade Sharpening1.A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Cleaning Drive Disc & Driven Disc Driven and Drive Disc ServiceDrive Spring Repair/Replacement Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments Belt Service Engine Drive Belt Replacement Stretch Type BeltsOn Next Pulley Position Reinstall blade hub and cutter bladeNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Testing Battery Service 1. Remove batteryCorrective Action Problem Probable CauseMAINTENANCE/REPLACEMENT Parts Service Performed Each100 USE HRS SeasonDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Page Page Page Steel Deck Recycling Walk Mowers Series

RP216019KWV, RP217019BV, RP217019BVE, RP2167519B specifications

The Snapper RP2167519B, RP217019BV, RP217019BVE, and RP216019KWV are standout models in Snapper's line of riding lawn mowers, designed for homeowners seeking efficiency, durability, and performance. Each model showcases a blend of innovative technologies and thoughtful engineering, making them suitable for various lawn care needs.

The RP2167519B features a robust 42-inch cutting deck powered by a reliable and efficient engine. This model comes equipped with a hydrostatic transmission, which allows for smooth acceleration and easy maneuverability, enabling users to tackle large lawns with ease. Its compact design makes it ideal for fitting into smaller spaces, while the adjustable cutting height gives users the flexibility to maintain their grass at the desired length.

The RP217019BV is another excellent option that boasts a powerful 19.5 HP engine. This model is equipped with a high-performance gear drive, providing users with enhanced control and responsiveness. The 42-inch deck is complemented by a side discharge feature, efficiently dispersing grass clippings while mowing. Furthermore, the ergonomic seating and user-friendly controls ensure comfort during extended use, making lawn care a more pleasant experience.

For those looking for added versatility, the RP217019BVE is a standout model with enhanced features. Similar in build to the RP217019BV, this variant introduces electric start technology, eliminating the need for manual pulling and simplifying the start-up process. The model incorporates a sturdy frame and premium materials, ensuring longevity and resilience over years of regular use. A mulching kit can also be easily added, offering users different options for maintaining their lawns.

Lastly, the RP216019KWV offers a unique combination of power and efficiency in a compact design. Featuring a 19 HP engine, this model is designed to operate quietly while delivering excellent cutting performance. Its easy-to-use controls and superior maneuverability make it a fantastic choice for homeowners with intricate landscaping. The model’s maintenance-free transmission is another highlight, as it requires less upkeep compared to traditional gear systems.

In summary, the Snapper RP2167519B, RP217019BV, RP217019BVE, and RP216019KWV provide users with reliable options tailored to various mowing needs. With their powerful engines, versatile features, and user-friendly designs, these riding mowers stand out as excellent investments for efficient lawn care. Whether for efficiency, comfort, or performance, Snapper consistently delivers quality in their riding lawn mowers.
Top Page Image Contents